Line 6 POD X3 Family manual Recording Tone 1 & 2 to Separate Mono Tracks

Page 84

Example Setups

Recording Tone 1 & 2 to Separate Mono Tracks

1.	Connect outputs to your recorder:
	• POD X3: connect the 1/4-inch outs.
	• POD X3 Live & POD X3 Pro: the XLR outputs are recommended for live sound
	systems, to provide a level that approximately matches a mic’ed up amp. You can
	also use them for recording into mic preamps, or use the 1/4-inch outputs to get
	hotter, line level outputs.
2.	Set the second OUTPUTS page (Studio/Direct Mix):
	• Tone 1: On
	• Tone 1 Pan: pan left
	• Tone 2: On
	• Tone 2 Pan: pan right
3.	When using the 1/4-inch jacks, also set the first OUTPUTS page (1/4-inch):
7•2	• Mode: MATCH STUDIO/DIRECT

4. In your recording system, assign those outputs to separate recording tracks.

Recording Tone 1 & 2 to Separate Stereo Tracks (POD X3 Live & POD X3 Pro only)

1.Connect the 1/4-inch left/right outputs to your recorder as the source for the first track, and the XLR left/right outputs as the source for the second track.

2.Set the second OUTPUTS page (Studio/Direct Mixer):

•Mode: Studio/Direct

•Tone 1: Off

•Tone 2: On (the XLRs will output Tone 2 only)

•Tone 2 Pan: Center

Image 84

Contents POD X3 Family Serial no Please Note Table of Contents Reference Configuration & Setup Example SetupsAppendix a Signal Flow USB & Computer SoftwarePage Tutorial POD X3 Live for Guitar Tweak the Amp Tone Controls Pick a Stomp Model and tweak it Show the Delay settings Tweak the EQ Turn both Tones on at once Select and Tweak Tone 1/Tone Tweak combined volume of Tone 1 + Tone Save Tutorial POD X3 & POD X3 Pro For GuitarTurn on the Amp Model DOUBLE-PRESS to Adjust Tap delay tempo Press down To select Lower row Tap is set to Preset loads into Tone These knobs and buttons control only one Tone at a time Controls & Connections PODControls & Connections Controls & Connections Tempo that you’ve tapped Input 2/Microphone In and Trim plug in your microphone here Controls & Connections Join the Club POD X3 Live Controls & Connections 310 Controls & Connections Controls & Connections 313 314 315 POD X3 Pro 316Controls & Connections 318 319 320 321 322 323 Page Getting Around, Tones & Tuner HomeBlock not selectedBlock selected Turn to tweak lower row settings Dual Tone Concept Hold Tone Volume Controls Preset Folders Recalling Presets You can also choose to recall only ToneRecalling User Presets on POD X3 Live Or only ToneLocking Tone Saving Tones410 Tuner 440HZ411 Page Reference Tweaking Tones Amp + CabTone Controls Guitar Amp Model Tone ControlsBass Amp Model Tone Controls Stomp Boxes Distortion Stomp BoxesDynamics Stomp Boxes ReferenceTweaking Tones Modulation Effects ReferenceTweaking Tones Delay 510 Reverb Gate Compressor 513514 Wah 515Volume Pedal 516Effects Loop POD X3 Live & POD X3 Pro only MIXPage Reference Configuration & Setup InputsOutputs Reference Configuration & Setup Outputs Page 2 Studio/Direct Mix System Page 1 Pedal and other settings SystemSystem Page 2 Pedal and other settings Commands Page Example Setups Mono or Stereo Recording or Direct to Mixer/PARecording Tone 1 & 2 to Separate Mono Tracks Feed One Guitar Amp Feed Two Guitar Amps, One for Tone 1 and One for ToneFeed Two Guitar Amps, One Wet and One Dry Example Setups Example Setups Example Setups Page USB & Computer Software Updating POD X3, POD X3 Live or POD X3 Pro’s FirmwareSetting Up For USB Recording USB Sends When Operating In Stereo Tone Mode Page Ppendix IgnalFlow POD X3 Live POD X3 Pro