Line 6 POD X3 Family manual Tone Volume Controls

Page 50

Getting Around,Tones & Tuner

Tone Volume Controls

The Tone Volume knob adjusts the volume of the Tone that is currently selected. Use this control to set the correct balance between Tone 1 and Tone 2.

From the Home Page, the rightmost Multi-functionknob lets you adjust the volume of Tone 1 + Tone 2. Back off on this control if you’re seeing the Clip light turn on. This level is saved and recalled with each preset.

4•6

Tone Volume adjusts the volume of the currently selected Tone.

Multifunction Knob 4 adjusts the volume of both Tones at once.

You probably want all of your favorite sounds as loud as possible, while also having the right difference in volume between your lead and rhythm sounds, clean and dirty sounds, etc. Right? OK, then, to get this happy balance, start with your favorite ‘clean’ sounds.

Turn up their volume as high as you can without getting the Clip indicator to light when you strum hard, and save them that way. Then switch amongst them to see if some are too loud, and turn them down a bit to match well with the others.

Next, move on to select your ‘dirtier’ crunch and lead tones, comparing them to the clean sounds and saving them with lower volume settings to match well with those clean sounds.

Now, each time you use your POD X3, POD X3 Live or POD X3 Pro, you just have to set a Master Volume level you like, and you can switch amongst your various sounds without unhappy volume differences.

Image 50
Contents POD X3 Family Serial no Please Note Table of Contents Appendix a Signal Flow Reference Configuration & SetupExample Setups USB & Computer SoftwarePage Tutorial POD X3 Live for Guitar Tweak the Amp Tone Controls Pick a Stomp Model and tweak it Show the Delay settings Tweak the EQ Turn both Tones on at once Select and Tweak Tone 1/Tone Tweak combined volume of Tone 1 + Tone Save Tutorial POD X3 & POD X3 Pro For GuitarTurn on the Amp Model DOUBLE-PRESS to Adjust Tap delay tempo Press down To select Lower row Tap is set to Preset loads into Tone These knobs and buttons control only one Tone at a time Controls & Connections PODControls & Connections Controls & Connections Tempo that you’ve tapped Input 2/Microphone In and Trim plug in your microphone here Controls & Connections Join the Club POD X3 Live Controls & Connections 310 Controls & Connections Controls & Connections 313 314 315 POD X3 Pro 316Controls & Connections 318 319 320 321 322 323 Page Getting Around, Tones & Tuner HomeBlock not selectedBlock selected Turn to tweak lower row settings Dual Tone Concept Hold Tone Volume Controls Preset Folders Recalling Presets You can also choose to recall only ToneRecalling User Presets on POD X3 Live Or only Tone410 Locking ToneSaving Tones 411 Tuner440HZ Page Reference Tweaking Tones Amp + CabTone Controls Guitar Amp Model Tone ControlsBass Amp Model Tone Controls Stomp Boxes Distortion Stomp BoxesDynamics Stomp Boxes ReferenceTweaking Tones Modulation Effects ReferenceTweaking Tones Delay 510 Reverb Gate Compressor 513514 Wah 515Volume Pedal 516Effects Loop POD X3 Live & POD X3 Pro only MIXPage Reference Configuration & Setup InputsOutputs Reference Configuration & Setup Outputs Page 2 Studio/Direct Mix System Page 1 Pedal and other settings SystemSystem Page 2 Pedal and other settings Commands Page Example Setups Mono or Stereo Recording or Direct to Mixer/PARecording Tone 1 & 2 to Separate Mono Tracks Feed One Guitar Amp Feed Two Guitar Amps, One for Tone 1 and One for ToneFeed Two Guitar Amps, One Wet and One Dry Example Setups Example Setups Example Setups Page USB & Computer Software Updating POD X3, POD X3 Live or POD X3 Pro’s FirmwareSetting Up For USB Recording USB Sends When Operating In Stereo Tone Mode Page Flow PpendixIgnal POD X3 Live POD X3 Pro