Line 6 POD X3 Family manual Effects Loop POD X3 Live & POD X3 Pro only, Mix

Page 73

Reference:Tweaking Tones

Effects Loop (POD X3 Live & POD X3 Pro only)

 

EFFECT LOOP

1

-58dB

+24dB

100%

 

 

 

 

POST

SEND

RETURN

MIX

CONFIG

75%

75%

75%

 

TYPE

TYPE

BYP VOL

 

This lets you tweak the settings related to the Effects Loop. Note that the Loop can only

be on for one Tone at a time, and turning the Loop on for one Tone automatically forces 5•17 it off for the other.

Send – adjusts the gain of the send output from -80 to 0 dB.

Return – adjusts the gain of the return inputs from 0 to +24 dB.

Mix – 0-100%: set this to 100% for parallel-style operation.

Config – allows you to place the Effect Loop in two different locations in the POD X3 Live and POD X3 Pro’s signal chain:

Pre – after the Stomp block, before the Mod and Delay blocks.

Post – before the Mod, Delay and Reverb blocks.

If nothing is connected to the loop, POD X3 Live and POD X3 Pro are smart enough to disable the loop so you still get sound.

Image 73
Contents POD X3 Family Serial no Please Note Table of Contents Example Setups Reference Configuration & SetupAppendix a Signal Flow USB & Computer SoftwarePage Tutorial POD X3 Live for Guitar Tweak the Amp Tone Controls Pick a Stomp Model and tweak it Show the Delay settings Tweak the EQ Turn both Tones on at once Select and Tweak Tone 1/Tone Tweak combined volume of Tone 1 + Tone Save For Guitar Tutorial POD X3 & POD X3 ProTurn on the Amp Model DOUBLE-PRESS to Adjust Tap delay tempo Press down To select Lower row Tap is set to Preset loads into Tone These knobs and buttons control only one Tone at a time POD Controls & ConnectionsControls & Connections Controls & Connections Tempo that you’ve tapped Input 2/Microphone In and Trim plug in your microphone here Controls & Connections Join the Club POD X3 Live Controls & Connections 310 Controls & Connections Controls & Connections 313 314 315 316 POD X3 ProControls & Connections 318 319 320 321 322 323 Page Home Getting Around, Tones & TunerBlock not selectedBlock selected Turn to tweak lower row settings Dual Tone Concept Hold Tone Volume Controls Preset Folders You can also choose to recall only Tone Recalling PresetsOr only Tone Recalling User Presets on POD X3 LiveSaving Tones Locking Tone410 440HZ Tuner411 Page Amp + Cab Reference Tweaking TonesGuitar Amp Model Tone Controls Tone ControlsBass Amp Model Tone Controls Distortion Stomp Boxes Stomp BoxesDynamics Stomp Boxes ReferenceTweaking Tones Modulation Effects ReferenceTweaking Tones Delay 510 Reverb Gate 513 Compressor514 515 Wah516 Volume PedalMIX Effects Loop POD X3 Live & POD X3 Pro onlyPage Inputs Reference Configuration & SetupOutputs Reference Configuration & Setup Outputs Page 2 Studio/Direct Mix System System Page 1 Pedal and other settingsSystem Page 2 Pedal and other settings Commands Page Mono or Stereo Recording or Direct to Mixer/PA Example SetupsRecording Tone 1 & 2 to Separate Mono Tracks Feed Two Guitar Amps, One for Tone 1 and One for Tone Feed One Guitar AmpFeed Two Guitar Amps, One Wet and One Dry Example Setups Example Setups Example Setups Page Updating POD X3, POD X3 Live or POD X3 Pro’s Firmware USB & Computer SoftwareSetting Up For USB Recording USB Sends When Operating In Stereo Tone Mode Page Ignal PpendixFlow POD X3 Live POD X3 Pro