Pioneer VSX-53TX manual Specifications

Page 106

Techno Tidbits and Problem-solving

Specifications

Amplifier Section

Continuous average power output of 100 watts* per channel, min., at 8 ohms, from 20 Hz to 20,000 Hz with no more than 0.09%** total harmonic distortion (front).

Continuous Power Output

Front

100 W +100

W (20

Hz – 20 kHz, 0.09%,

8 Ω)

Center

100

W (20

Hz – 20 kHz, 0.09%, 8

Ω)

Surround

100 W +100 W (20 Hz – 20 kHz, 0.09%, 8

Ω)

Surround Back

 

 

 

 

...............

100 W +100 W (20 Hz – 20 kHz, 0.09%,

8

Ω)

Audio Section

Input (Sensitivity/Impedance)

 

LINE

335 mV/47 kΩ

Frequency Response

 

LINE

5 Hz to 100,000 Hz +–30dB

Output (Level/Impedance)

 

LINE

335 mV/2.2 kΩ

Tone Control

 

BASS

± 6 dB (100 Hz)

TREBLE

± 6 dB (10 kHz)

LOUDNESS

+4/+2 dB (100Hz/10 kHz)

 

(at volume position –40dB)

Signal-to-Noise Ratio (IHF, short circuited, A network)

LINE

101 dB

Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]

LINE

83 dB

*Measured pursuant to the Federal Trade Commission’s Trade Regulation rule on Power Output Claims for Amplifiers.

**Measured by Audio Spectrum Analyzer.

Video Section (S jack)

Input (Sensitivity/Impedance)

............................... 1 Vp-p/75 Ω

Output (Level/Impedance)

1 Vp-p/75 Ω

Frequency Response

5 Hz to 10 MHz +–30dB

Signal-to-Noise Ratio

65 dB

Video Section (Composite)

Input (Sensitivity/Impedance)

 

LINE

1 Vp-p/75 Ω

Output (Level/Impedance)

 

LINE

1 Vp-p/75 Ω

Frequency Response

 

LINE

5 Hz to 10 MHz +–03dB

Signal-to-Noise Ratio

65 dB

FM Tuner Section

Frequency Range

87.5 MHz to 108 MHz

Usable Sensitivity

Mono: 13.2 dBf, IHF (1.3 µV/75 Ω)

50 dB Quieting Sensitivity

Mono: 20.2 dBf

 

 

Stereo: 38.6 dBf

Signal-to-Noise Ratio

Mono: 73 dB (at 85 dBf)

 

 

Stereo: 70 dB (at 85 dBf)

Distortion

Stereo: 0.5 % (1 kHz)

Alternate Channel Selectivity

.........................60 dB (400 kHz)

Stereo Separation

40 dB (1 kHz)

Frequency Response

30 Hz to 15 kHz (± 1) dB

Antenna Input

75 Ω unbalanced

AM Tuner Section

Frequency Range

530 kHz to 1,700 kHz

Sensitivity (IHF, Loop antenna)

350 µV/m

Selectivity

25 dB

Signal-to-Noise Ratio

50 dB

Antenna

Loop antenna

Miscellaneous

Power Requirements

AC 120 V, 60 Hz

Power Consumption

600 W

Power Consumption in Standby mode

...........................0.8 W

AC Outlet SWITCHED

100 W (0.8 A) MAX

Dimensions

420 (W) × 188 (H) × 464 (D) mm

(16-9/16 (W) × 7-7/16 (H) × 18-5/16 (D) in.)

Weight (without package)

17.4 kg (38.6 lbs)

Component Video Section

Input (Sensitivity)

1 Vp-p/75 Ω

Output (Level/Impedance)

1 Vp-p/75 Ω

Frequency Response

5 Hz to 40 MHz +–03dB

Signal-to-Noise Ratio

65 dB

Furnished Parts

 

FM wire Antenna

1

AM loop Antenna

1

“AA” IEC LR6 batteries

2

Remote Control Unit

1

Microphone for Auto Surround Sound Setup

1

Microphone Stand for Auto Surround Sound Setup

1

Operating Instructions

1

NOTE:

Specifications and the design are subject to possible modifi- cations without notice, due to improvements.

106

Page 105 Page 107
Image 106
Page 105 Page 107
Contents Page Page Page Table of Contents Easy Setup Guide Preparation Surround Setup Basic Expert 12V Trigger FeaturesB fore You StartMultichannel Acoustic Calibration EQ System Mcacc Audio Scaler HI BIT/HI SamplingBefore You Start Checking the Supplied AccessoriesPreparing the Remote Control Loading the batteriesOpening the Front Panel Installing the ReceiverOperating range of remote control unit Inches 20 cm ReceiverEasDi playsSetup& ControlsGuidePart Home Theater The BasicsHooking Up Your DVD Player and TV Digital ConnectionsSpeaker Connections  Speaker terminalsSetting up the Main Unit Assigning the Digital InputsEasy Setup Guide Part Auto Surround Sound SetupCheck the speaker settings on the OSD For loud test tonesPlaying a DVD with Surround Sound Normal useVideo Connecting your TVComponent Video Input Default Settings Component videoConnecting Video Components Connecting a DVD playerConnecting VCRs or DVRs Connecting a Video Component to the Front PanelConnecting Satellite TV SAT Components Satellite tunerConnecting Analog Audio Components  Audio cordsPreparation Connecting Digital Audio Components Not a PCM-only outputDigital Input Default Settings  Coaxial cords/Optical cablesUsing outdoor antennas Connecting the Radio Antennas AM loop antenna Connecting Speakers Bi-wiring your speakers Speaker impedanceSpeaker placement Power Connections AC OutletsPlacing Your Speakers Displays& Controlsand Controls Front PanelSB CH Mode button see Master Volume dialSignal Select button see Setup MIC jack seeRemote Control +/- buttons Signal SEL button seeBASS/TREBLE buttons see Multi Operation button EFFECT/CH SEL buttonTOP MENU/GUIDE button Master Volume +/- buttonsRemote Setup button 16 ////ENTER buttonsDisplay Back Panel Speakers terminals see AC Outlet switched, 100 W maxMULTI-ROOM & Source Remote in terminal see Digital in terminals seeTurn on the receiver and your TV. Press Through the menus. When you haveSetting you want in a particular menu TrolIf it isn’t use the  buttons to select it Surround Back SystemExit should be selected. Press the Enter button When you have the setting you want Normal SetupThrough the Normal setup menus Use the  buttons to select NormalCenter default setting is Small Speaker SettingFront default setting is Small Surround default setting is SmallNumber YES or NO, X1 or X2 With the  buttons chooseUse the  buttons to choose Size Large or Small for each setIsn’t use the  buttons to select Setting mode with the  buttonsChannel Level Level Manual or AUTO. Select aSelect it. Press the Enter button Speaker DistanceSpeaker Distance should be Select each speaker channel withBasic Operation Choose a Listening Mode one of two waysIndicator Stereo and Multichannel PlaybackSelecting the Input Signal Listening Modes Stereo modesMovie modes Surround mode THX Cinema 2PL II Movie 2PRO Logic II MovieMusic modes Surround mode 2PL II Music 2PRO Logic II MusicAdjusting the Effect of a Listening Mode Adding/Adjusting the Effect in Dolby Pro Logic II Music ModeDigital Noise Reduction Digital NR Function Press Receiver Press the DNR button on the remote controlListening with Acoustic CAL EQ Press the Acoustic EQ buttonListening in Loudness Mode Listening in Midnight ModePress the Midnight button on the remote control Adjusting Bass and Treble Listening with Sound DelayListening in Audio Scaler mode This mode cannot be used with Multi CH in modeMulti Channel In Playback Virtual Surround Back Mode Surround Back Channel ModePress the SB CH Mode button on the remote control Press the SB CH Mode button onPlug headphones into the Phones Dual Mono setting and playbackUsing Headphones Jack on the front of the receiverAdjusting the Brightness of the Display Dimmer Video SelectMPX Mode Using the TunerUsing the TunerAutomatic and Manual Tuning Press the Tuner buttonPress the Band button to select the band FM or AM Direct Access TuningTo cancel before inputting the frequency ExampleTune in the station you want Memorizing Frequently Used StationsPress the Enter button to input your choice Naming Memorized Stations Use the number buttons to select the channel you want Recalling Memorized StationsTo step through each channel in order Recalling Settings Stored in the Remote Control Setting Up the Remote Control to Control Other ComponentsRemoteDisplays & Controlontrols of Other Components Programming Signals from Other Remote Controls Learning Mode Press the button to be programmedUsing Remote Control with Other Components CD/MD/CD-R/VCR/DVD/LD/DVD Recorder/Cassette Deck operationsCable TV/Satellite TV/Digital TV/TV operations ReturnSetting up the Direct Function Turn on the receiver Using Other FunctionsUsing Other FunctionsRecording from Audio/Video Components Start recording tape deck, CD Recorder, VCR, etcSecond Zone Speaker System B Setup Connecting Additional Amplifiers Multi Room function Setup exampleMulti Room connections ROOM. Press Enter Using Other FunctionsUse the  buttons to select Multi It isnt use the  buttons to selectYou can adjust the volume level in the following range Press the Control button to enter the control modeAdjust the volume Select the source with the Multi JOGControlling the Multi Room system from the sub room Press Volume +/- to adjustVolume From the sub room, point the remotePioneer SR System Operating other Pioneer components Multi Operations Select a Multi Control button for this multi operationPerforming Multi Operations Press the Receiver button Using System OFFSystem Off Select a Multi Control button forResetting the Remote Control When OK appears in the display all the settings Resetting the Main UnitWhen you see RESET? appear Press the STANDBY/ON button forTHX Cinema Setup DIGITAL-IN Select should be When youre finished use the Input ASSIGN. Press the Enter Selected, if not use the  buttons toReassign. Press the Enter button Assigning the Component Video InputsComponent video input you want to Use the  buttons to assign a receiver functionFunction Rename 12V Trigger function Expert System Settings Expert SetupCrossover Network should be Crossover NetworkTo select and press Enter Fine Channel Level Use the  buttons to adjustAdjust the level of the channel using Fine Channel Level should beAdjust the distance of each channel using the  buttons Fine Channel DelayFine Channel Delay should be Distance of the left channel. PressWhen done select Exit if it’s not EQ Auto Setting should beStart EQ Auto Setting Acoustic Calibration EQUse the  buttons to select CUS Use the  buttons to select DataCOPY. Press Enter TOM 1 or Custom 2 as the destinaFor explanation purposes Illustrations use ALL CH Adjust This explanation is for Custom 1 or CustomUse the  buttons to adjust Trim and press Enter To use the Data Check feature follow the steps here Bass Peak Level Start or Setting CANCEL. PressUse the buttons to adjust the test Tone and specify the bass peak levelOFF, MID or MAX. Press Enter Dynamic Range ControlRange Control should be  buttons to select it, pressDolby Digital Chart Comparing Dolby Pro Logic and Dolby Pro LogicDolby Dolby Pro LogicDTS Neo6 DTS 96/24Power Power does not turn on TroubleshootingOverheat blinks in the display and no sound is output To be something wrong with Setup Setup screen doesnt appearNo audio No sound is output when a SoundNo sound output from the subwoofer No sound output from one set of speakersOther audio problems Considerable noise in radio broadcastsVideo jacks Cant record video Video No image is output when aThere is no image coming Input/displayOther components cant be operated with the system remote Remote controlShow 96kHz MiscellaneousPreset Code Brands DVDMaintenance of External Surfaces EIASpecifications TNMWF/03C00001 Printed
Top Page Image Contents