Pioneer VSX-53TX manual Second Zone Speaker System B Setup

Page 68

Using Other Functions

SECOND ZONE (Speaker System B) Setup

Stereo playback in another room

This setup enables you to listen to a pair of stereo speakers independently of the main speaker system (A speakers) hooked up to the receiver. The VSX-53TX has two possibilities for playback in another room. You can choose SECOND ZONE, and use the speakers hooked up to the surround back terminals as a B speaker system, that is, playing the same source as the main speaker system but from independent stereo speakers. Or, you can choose MR&S and use the speakers hooked up to the surround back terminals for MULTI-ROOM playback (see pages page 70 for more on MULTI-ROOM).

1Connect a pair of speakers to the surround back speaker terminals.

2Select SECOND ZONE or MR&S (MULTI-ROOM) in the SURRBACK SYSTEM setup (see page 37).

Memo:

Please use speakers with a nominal impedance rated 8 Ω-16 Ω.

SPEAKERS Button

If you selected NORMAL SYSTEM in the SURRBACK SYSTEM setup (see page 37) your surround back speakers will be used as part of your A speakers (main speaker system) and this button will simply switch it off or on. If you selected MR&S in the SURRBACK SYSTEM setup (see page 37) the surround back speakers will be used for the MULTI-ROOM and this button will simply switch A speakers (main speaker system) on or off. If you selected SECOND ZONE in the SURRBACK SYSTEM setup (see page 37) this button will cycle through the A (main) speaker system, the B speaker system (the surround back speakers acting as a separate second zone), both speaker systems, and off.

1

Press the SPEAKERS button (on the

 

front panel) to switch speakers on/

 

off or cycle through the different

 

speaker systems if SECOND ZONE has

1

been selected in the SURRBACK SYS-

TEM setup (see page 37).

A(SPA):

Sound is output from speaker system A and the same signal is output from the pre out

 

terminals.

B(SPB):

Sound is output from the two speakers in speaker system B (the surround back speakers).

 

Multichannel sources won't be heard from these speakers.

A&B(SPAB):Sound is output from speaker system A and the B speakers. Multichannel sources will be downmixed to two channels.

OFF(SP): No sound is output from the speakers. Depending on the input signal and settings in SPEAKER SETTING sound may be output from the subwoofer. The same sound is output from the pre out terminals as when selecting speaker system A (above).

Memo:

•What is output from the subwoofer depends on the SPEAKER SETTING settings and the type of source.

•Depending on the settings in SPEAKER SETTING and the MULTI CH IN SELECT, output from the SURROUND BACK pre out terminals may change.

•When using headphones the speakers are switched off.

•Please use speakers with a nominal impedance rated 8 Ω-16 Ω.

68

Page 67 Page 69
Image 68
Page 67 Page 69
Contents Page Page Page Table of Contents Easy Setup Guide Preparation Surround Setup Basic Expert FeaturesB fore You Start Multichannel Acoustic Calibration EQ System Mcacc12V Trigger Audio Scaler HI BIT/HI SamplingChecking the Supplied Accessories Preparing the Remote ControlBefore You Start Loading the batteriesInstalling the Receiver Operating range of remote control unitOpening the Front Panel Inches 20 cm ReceiverEasDi playsSetup& ControlsGuidePart Home Theater The BasicsHooking Up Your DVD Player and TV Digital ConnectionsSpeaker Connections  Speaker terminalsSetting up the Main Unit Assigning the Digital InputsEasy Setup Guide Part Auto Surround Sound SetupCheck the speaker settings on the OSD For loud test tonesPlaying a DVD with Surround Sound Normal useConnecting your TV Component Video Input Default SettingsVideo Component videoConnecting Video Components Connecting a DVD playerConnecting VCRs or DVRs Connecting a Video Component to the Front PanelConnecting Satellite TV SAT Components Satellite tunerConnecting Analog Audio Components  Audio cordsPreparation Connecting Digital Audio Components Not a PCM-only outputDigital Input Default Settings  Coaxial cords/Optical cables AM loop antenna Connecting the Radio AntennasUsing outdoor antennas Connecting Speakers Bi-wiring your speakers Speaker impedancePlacing Your Speakers Power Connections AC OutletsSpeaker placement Displays& Controlsand Controls Front PanelMaster Volume dial Signal Select button seeSB CH Mode button see Setup MIC jack seeRemote Control Signal SEL button see BASS/TREBLE buttons see Multi Operation button+/- buttons EFFECT/CH SEL buttonMaster Volume +/- buttons Remote Setup buttonTOP MENU/GUIDE button 16 ////ENTER buttonsDisplay Back Panel AC Outlet switched, 100 W max MULTI-ROOM & Source Remote in terminal seeSpeakers terminals see Digital in terminals seeThrough the menus. When you have Setting you want in a particular menuTurn on the receiver and your TV. Press TrolExit should be selected. Press the Enter button Surround Back SystemIf it isn’t use the  buttons to select it Normal Setup Through the Normal setup menusWhen you have the setting you want Use the  buttons to select NormalSpeaker Setting Front default setting is SmallCenter default setting is Small Surround default setting is SmallWith the  buttons choose Use the  buttons to chooseNumber YES or NO, X1 or X2 Size Large or Small for each setSetting mode with the  buttons Channel LevelIsn’t use the  buttons to select Level Manual or AUTO. Select aSpeaker Distance Speaker Distance should beSelect it. Press the Enter button Select each speaker channel withChoose a Listening Mode one of two ways IndicatorBasic Operation Stereo and Multichannel PlaybackSelecting the Input Signal Listening Modes Stereo modesMovie modes Surround mode THX Cinema 2PL II Movie 2PRO Logic II MovieMusic modes Surround mode 2PL II Music 2PRO Logic II MusicAdjusting the Effect of a Listening Mode Adding/Adjusting the Effect in Dolby Pro Logic II Music ModePress Receiver Press the DNR button on the remote control Listening with Acoustic CAL EQDigital Noise Reduction Digital NR Function Press the Acoustic EQ buttonPress the Midnight button on the remote control Listening in Midnight ModeListening in Loudness Mode Adjusting Bass and Treble Listening with Sound DelayListening in Audio Scaler mode This mode cannot be used with Multi CH in modeMulti Channel In Playback Surround Back Channel Mode Press the SB CH Mode button on the remote controlVirtual Surround Back Mode Press the SB CH Mode button onDual Mono setting and playback Using HeadphonesPlug headphones into the Phones Jack on the front of the receiverAdjusting the Brightness of the Display Dimmer Video SelectUsing the TunerUsing the Tuner Automatic and Manual TuningMPX Mode Press the Tuner buttonDirect Access Tuning To cancel before inputting the frequencyPress the Band button to select the band FM or AM ExamplePress the Enter button to input your choice Memorizing Frequently Used StationsTune in the station you want Naming Memorized Stations To step through each channel in order Recalling Memorized StationsUse the number buttons to select the channel you want RemoteDisplays & Controlontrols of Other Components Setting Up the Remote Control to Control Other ComponentsRecalling Settings Stored in the Remote Control Programming Signals from Other Remote Controls Learning Mode Press the button to be programmedUsing Remote Control with Other Components CD/MD/CD-R/VCR/DVD/LD/DVD Recorder/Cassette Deck operationsCable TV/Satellite TV/Digital TV/TV operations ReturnSetting up the Direct Function Using Other FunctionsUsing Other Functions Recording from Audio/Video ComponentsTurn on the receiver Start recording tape deck, CD Recorder, VCR, etcSecond Zone Speaker System B Setup Connecting Additional Amplifiers Multi Room connections Setup exampleMulti Room function Using Other Functions Use the  buttons to select MultiROOM. Press Enter It isnt use the  buttons to selectPress the Control button to enter the control mode Adjust the volumeYou can adjust the volume level in the following range Select the source with the Multi JOGPress Volume +/- to adjust VolumeControlling the Multi Room system from the sub room From the sub room, point the remotePioneer SR System Operating other Pioneer components Multi Operations Select a Multi Control button for this multi operationPerforming Multi Operations Using System OFF System OffPress the Receiver button Select a Multi Control button forResetting the Remote Control Resetting the Main Unit When you see RESET? appearWhen OK appears in the display all the settings Press the STANDBY/ON button forTHX Cinema Setup When youre finished use the  Input ASSIGN. Press the EnterDIGITAL-IN Select should be Selected, if not use the  buttons toAssigning the Component Video Inputs Component video input you want toReassign. Press the Enter button Use the  buttons to assign a receiver functionFunction Rename 12V Trigger function Expert System Settings Expert SetupTo select and press Enter Crossover NetworkCrossover Network should be Use the  buttons to adjust Adjust the level of the channel usingFine Channel Level Fine Channel Level should beFine Channel Delay Fine Channel Delay should beAdjust the distance of each channel using the  buttons Distance of the left channel. PressEQ Auto Setting should be Start EQ Auto SettingWhen done select Exit if it’s not Acoustic Calibration EQUse the  buttons to select Data COPY. Press EnterUse the  buttons to select CUS TOM 1 or Custom 2 as the destinaFor explanation purposes Illustrations use ALL CH Adjust This explanation is for Custom 1 or CustomUse the  buttons to adjust Trim and press Enter To use the Data Check feature follow the steps here Start or Setting CANCEL. Press Use the buttons to adjust the testBass Peak Level Tone and specify the bass peak levelDynamic Range Control Range Control should beOFF, MID or MAX. Press Enter  buttons to select it, pressChart Comparing Dolby Pro Logic and Dolby Pro Logic DolbyDolby Digital Dolby Pro LogicDTS Neo6 DTS 96/24Overheat blinks in the display and no sound is output TroubleshootingPower Power does not turn on Setup Setup screen doesnt appear No audio No sound is output when aTo be something wrong with SoundNo sound output from the subwoofer No sound output from one set of speakersOther audio problems Considerable noise in radio broadcastsVideo No image is output when a There is no image comingVideo jacks Cant record video Input/displayRemote control Show 96kHzOther components cant be operated with the system remote MiscellaneousPreset Code Brands DVDMaintenance of External Surfaces EIASpecifications TNMWF/03C00001 Printed
Top Page Image Contents