Alesis 60 Storing effects programs, Copying effects programs from one location to another

Page 9

ROUTE

The order of the effects chain can be changed here.

This is the default order.

This one is the default order with FX2 and FX3 swapped to put the delay effects in the middle of the modulation effects.

This order places the cabinet simulator at the end.

This one is order 2 with FX2 and FX3 swapped.

This order is the default order with the compressor/limiter placed at the end, making this one ideal for recording.

This one is order 4 with FX2 and FX3 swapped.

This is the one to go for if you’re recording and want to sound like you’re running several effects pedals into an amp.

This configuration is order 6 with FX2 and FX3 swapped.

Storing effects programs

After you’ve created a configuration that you like, you can store it for future recall. To store your changes, press the VALUE knob and then turn the knob to select a store location. Press the VALUE knob again to store the program.

Copying effects programs from one location to another

Copying programs is easy. Just call up the program that you want to copy. Then, press the VALUE knob, twist it until you find the location where you want to store your copy, and press VALUE again to store the program in its new location.

Restoring factory defaults for the effect settings

Once you have saved changes to a preset program, you can still recall the original settings. To enter the RESTORE FACTORY PRESETS mode, simply hold down the VALUE knob as you turn the unit on and then select the program to be restored (or AL for all programs). Press the VALUE knob to confirm your selection. The display will blink rapidly several times to indicate the restore was successful. Any program changes you have made will be lost, so you might want to copy the program to another location first.

To exit the RESTORE FACTORY PRESETS mode, just turn the EFFECTS knob. You can also turn the Bassfire off and then on again, without holding down any knobs or buttons, to exit the RESTORE FACTORY PRESETS mode.

7

Image 9

Contents Manual de inicio rápido para el usuario Español This page intentionally left blank Quick Setup for the Bassfire Rear panel operation Front panel operationExploring the Bassfire’s effects Modifying effects programsCOMP/LIMIT Compressor/Limiter Drive increases or decreases the Dist level Dist DistortionEQ Equalizer NR Noise ReductionClassic Effects FX1, FX2, and FX3 Powerful lows that can damage certain equipmentSample Rate Decimation. Creates low-fi effects Digfx Digital Sampling EffectsRestoring factory defaults for the effect settings Storing effects programsCopying effects programs from one location to another Using the built-in tuner Deferred program changeBypassing the effects Tuning to a pitch other than A=440 This page intentionally left blank Instalación rápida del Bassfire Manual de inicio rápido para el usuario EspañolCómo operar el panel posterior Cómo operar el panel frontalCómo modificar los programas de efectos Cómo explorar los efectos del BassfireDist Distorsión COMP/LIMIT Compresión del compresor/limitadorDrive aumenta o disminuye el nivel de la distorsión EQ EcualizadorNR Reducción de ruido CAB Cabinet Simulator Simulador de caja acústicaEfectos clásicos FX1, FX2 y FX3 Efectos clásicos FX1, FX2 y FX3. Continuación Digfx Efectos digitales de muestreo o sampling Cómo guardar efectos de programasCómo copiar programas de efectos de un lugar a otro Cambio de programa diferidoDesviación de los efectos Afinar a un pitch diferente de A=440 Cómo usar el afinador tuner integradoThis page intentionally left blank Guide d’utilisation simplifié Français Guide d’installation rapide pour le BassfireFonctionnement du panneau arrière Fonctionnement du panneau avantModification des programmes d’effet La découverte des effets du BassfireDist Distorsion COMP/LIMIT Compresseur/LimiteurDrive augmente ou diminue le niveau de distorsion EQ ÉgaliseurNR Réduction du bruit CAB simulateur denceintesEffets classiques FX1, FX2, et FX3 Tonalité variable transposée à la baisse Effets classiques FX1, FX2, et FX3 SuiteLa sauvegarde des programmes d’effet Digfx Effets déchantillonage numériqueLevel Niveau Copier des programmes deffet dun emplacement à un Autre Modification du programme différéDérivation des effets Accorder à un ton autre que A=440 Utilisation de l’accordeur intégréThis page intentionally left blank Schnellaufbau des Bassfire Kurzbedienungsanleitung DeutschBedienelemente Rückseite Bedienungselemente VorderseiteVerändern von Effektprogrammen Probieren Sie die Effekte des Bassfire ausDrive erhöht oder verringert den DIST-Pegel Dist VerzerrungKlassische Effekte FX1, FX2, und FX3 NR RauschunterdrückungKlassische Effekte FX1, FX2, und FX3 Fortsetzung Level Pegel Digfx Digital Sampling-EffekteProgramme zum Abspeichern von Effekten Effektprogramme zwischen Speicherplätzen kopierenRoute Fortsetzung Umgehen der Effekte Ausschalten Verzögerter ProgrammwechselTunen auf eine andere Tonlage als A=440 Verwendung des eingebauten TunersImpostazione rapida Bassfire Manuale rapido di utilizzazione ItalianoCaratteristiche pannello posteriore Caratteristiche pannello anterioreModificare i programmi degli effetti Esplorare gli effetti del BassfireDist Distorsione COMP/LIMIT Compressore/LimitatoreDrive aumenta o diminuisce il livello di Dist EQ EqualizzatoreNR Noise Reduction Riduzione del rumore CAB Simulatore di casse acusticheEffetti Classici FX1, FX2, e FX3 Effetti Classici FX1, FX2, e FX3 Continua Digfx Effetti di campionatura digitale Memorizzazione di programmi di effettiRipristino impostazioni predefinite degli effetti Copiare i programmi di effetti da una posizione all’altraCambiamento di programma differito Deferred program change Bypassare gli effettiAccordare ad un pitch diverso da A=440 Uso del tuner incorporato