Peavey V12 owner manual Channel fader features, Button

Page 52

micro mute system

5

0

5

channel fader features

Aµ-button

This momentary switch is used to program the channel mutes when the Micro is in EDIT Mode. Pressing this switch will assign/un-assign it to a mute scene (either Sequenced or Manual), the internal yellow LED will blink to show an assignment.The operator uses these blinking LEDs to review the mute pattern being edited.These buttons are also used to send MIDI mute info when the Micro is in normal operation mode and MIDI Mutes is ON (see Utility). Pressing this switch sends a Note On/Off command that can be recorded on an external MIDI sequencer. If a corresponding Note On/Off command is received, the yellow LED lites up steady, and a mute command is issued to the channel.

B act LED (µ-mute)

This red LED lites whenever a Mute command is issued from the Micro.This can be from any of the Sequenced or Manual Mute Scenes or from a received MIDI Note command. Whether or not the channel responds to that mute command is determined by the status of two SAFE switches: the global Input Micro Safe switch (near master faders), or the channel Mute Safe switch.

mute safe

CThis switch "safes" the channel from external mute commands (micro,VCA, SIP). By default,theVCA and Solo-In-Place (SIP) mute commands are safed,but there are two jumpers located on each fader circuit board to exclude each of them.The micro mute commands (Man Mute, Seq Scene or MIDI mutes) are always affected by the safe.

act LED (VCA)

DThis red LED lights whenever a mute command is coming from an assigned VCA. Each VCA Master has an associated Mute switch.When depressed, any channels assigned to that VCA Master will go to a fader full-down condition (max attenuation),and the channel mute will be activated.A jumper in theVCA Master fader block can defeat the mute function; in that case, the channels still go to fader full-down, but the channel mute is not activated.

VCA assign

These 12 lit switches are used to assign a channel to any of the 12 VCA

EMasters.The channel gain is controlled by the sum of the voltages of the local fader and any of the assigned VCA Masters.The VCA control circuitry is designed so that even if a channel is assigned to all 12 masters, and those mas- ters are all at +10dB boost (total of +120dB theoretical gain!), the local fader (or any Master fader) , when pulled down, has enough electrical over-travel to fully attenuate the channel. Furthermore, the control voltage is electrically lim- ited to a maximum of +20dB gain to prevent excessive channel boost.

p. 52

Page 51 Page 53
Image 52
Page 51 Page 53
Contents V12 mixing console Direct output features Mono input moduleGroup assignment features Input features EQ features Aux features Aux send , 6, 7 Push-on/push-off switchAux send , 2, 3 Monitor features Solo switchSegment channel meter VCA-level LEDPage Stereo input module Dual level controlImage width control-WID Sum switchImage balance control Polarity-reverse switch Ground lift switchDual-concentric input gain control EQ features Aux features Aux send operation Dual 8-segment channel meter Page Mono-matrix features Group output module-matrix, aux, groupExternal-in signal-level to matrix Illuminated mute-switchMute switch Mute active-LEDInsert on-switch Peak and signal-present LEDTalkback preset-switch Output level-control rotary potMtx master and GRP master LED indicators Aux master features AUX-master and GRP-master LED indicators Group-assignment features Matrix post-switchGroup-to-matrix on-switch Mono-assignment switchGroup-master features Output level-control 100mm fader Module swap features Mode switch recessedMTX switch recessed FOH group LEDGroup rear-panel connectors Illuminated mute-switches Solo switchesVca masters 100mm fadersOutput mute safe switch Left, right and mono peak and signal-present LedsLeft/right/mono to matrix on-switch Matrix-post switchInput fader block Act LED µ-muteMute safe Act LED VCAStereo-matrix features Stereo matrix / aux out moduleExternal-in left and right signal-level to matrix Stereo matrix solo-switch Mtx to auxStereo matrix output-level control Stereo matrix output-balance controlDual-aux output features Talkback preset-switch One odd channel, one even channel 100mm output fader One per odd channel, one per even channelSolo switch Oscillator features Master modules-M1, M2Meter-view features Meters-A/meters-B switch bankAlternate output features Provides an area to label the alternate outputs usage Talkback master features Intercom interconnect features Console-to-intercom level and switchLink headphone/intercom switch Comms levelMonitor output features On-switch SumDim 100mm fader level-controlLeft-/right-output switch Headphone output featuresLCR output-monitoring 100mm headphone level-control Solo system features Page Micro panel features Micro mute systemManual mute-bank select Channel fader features ButtonVCA LED on module Normal operation mode Micro operationSelect Scene to edit Edit/preview rapid recall Edit/ViewExiting Edit Mode Other ways to exit Edit ModeUtility Mode UtilitiesClear Utilities Show ControlGeneral Controls Micro UtilitiesGeneral Controls Scene Resettingthe Micro Page V12 rear views Page V12 rear views
Related manuals
Manual 24 pages 8.07 Kb

V12 specifications

The Peavey V12 is a remarkable guitar amplifier that has gained a reputation for its versatility, punchy sound, and reliability. Aimed at guitarists across various genres, the V12 combines advanced technologies with user-friendly features, making it an appealing option for both amateur and professional musicians.

One of the standout features of the Peavey V12 is its power and performance. This amplifier delivers an impressive 120 watts of power, ensuring that it can handle large gigs and rehearsals with ease. Its dual gain structure allows players to explore a wide range of tone options, offering both clean sounds and high-gain distortion. This adaptability makes the V12 suitable for everything from blues to rock and metal.

The V12 boasts Peavey's patented TransTube technology, which emulates the warm, dynamic sound of tube amplifiers. This innovative technology provides a rich tonal palette, delivering the best of both worlds – the warmth of analog sound with the reliability of solid-state performance. Furthermore, the amp comes equipped with a three-channel configuration, giving users access to clean, crunch, and lead sounds at the push of a button. This makes it easy to switch between settings during live performances.

In addition to its tonal options, the Peavey V12 offers comprehensive EQ controls, including treble, mid, and bass adjustments. This allows guitarists to fine-tune their sound to suit their specific preferences and playing styles. The presence and resonance controls further enhance tonal shaping, enabling players to achieve a robust sound that cuts through the mix.

Another notable characteristic of the V12 is its durable construction. Built with high-quality materials, this amp can withstand the rigors of touring, making it a reliable choice for musicians on the road. The lightweight design also adds to its ease of transport, ensuring that musicians can take their sound anywhere.

Additional features include built-in reverb, allowing users to add depth to their tone, and a headphone output for silent practice. The amp is also compatible with footswitching, which gives players added control during performances.

In conclusion, the Peavey V12 is an exceptional amplifier that blends power, versatility, and cutting-edge technology. With its extensive sound-shaping capabilities and robust construction, it stands out as an ideal choice for guitarists seeking quality and performance in one package. Whether for practice, recording, or live performances, the V12 is designed to meet the demands of contemporary musicians.
Top Page Image Contents