Peavey V12 owner manual Resettingthe Micro

Page 62

micro mute system

when he scrolls to PASSWORD again before leaving the Utility Mode. Press CLEAR to clear the password to Off.

RESETTINGTHE MICRO:

The V-12 micro is designed for reliable, trouble-free operation , but it is, after all, a computer.There may be situations where it misbehaves. If this occurs, a reset is probably the best course of action.There are two types of reset: a normal, maintained reset; and a second, more encompassing reset- the Initialization Reset:

The first type occurs every time theV-12 powers up.The micro does some housekeeping, counts the number of channels present, and restores the Console’s mutes to their state prior to the last power-down. It does this in less than a second.All mute and scene information is retained along with any utility settings.

The second type of reset completely clears out the micro. In addition to clearing out all micro scratch memory, all utility functions are reset to their starting values and all mute and scene memories are cleared. This takes about a second, and you will be left with a console with no preset mutes and all settings at their factory defaults.

There are two methods to initiate a maintained reset:

The first is by powering the console down,waiting a second or so,and then back up.This method will, of course, cause audio discontinuities.The V-12 has power-up/down, anti-pop circuitry on all main balanced outs, but there will be a delay while the power supply comes up to spec and the main outs are muted.

The second method is to use the reset hole located below the Active Scene display.A straightened paper clip or push-pin can be used to trip the recessed reset switch.This will cause the micro to go through its normal power-up sequence- it will be ready to go in a flash (you may not even see the displays blink).The power supply is not involved,so normal audio oper- ation is maintained.

To perform a Initialization Reset, two buttons are held down on the key- pad while the micro is going thru a normal reset.You can do this when the console is powering up or you can start it by pressing the reset switch. Hold down the CLEAR and EDIT keys while a reset is performed.The dis- plays will clear out, and MEM INIT will appear in the upper display. Continue to hold the keys down until the normal Next/Active Scene dis- plays show up.TheV-12 is set to this state when it leaves the factory.There is no danger (other than data loss with the Init Reset) in doing either of these resets, the only warning involves audio that may become un-muted as a result. Please use caution if you are working on a live system.

p. 62

Page 61 Page 63
Image 62
Page 61 Page 63
Contents V12 mixing console Direct output features Mono input moduleGroup assignment features Input features EQ features Aux features Aux send , 2, 3 Push-on/push-off switchAux send , 6, 7 Segment channel meter Monitor featuresSolo switch VCA-level LEDPage Stereo input module Dual level controlImage balance control Sum switchImage width control-WID Dual-concentric input gain control Ground lift switchPolarity-reverse switch EQ features Aux features Aux send operation Dual 8-segment channel meter Page Mono-matrix features Group output module-matrix, aux, groupMute switch External-in signal-level to matrixIlluminated mute-switch Mute active-LEDTalkback preset-switch Insert on-switchPeak and signal-present LED Output level-control rotary potMtx master and GRP master LED indicators Aux master features AUX-master and GRP-master LED indicators Group-to-matrix on-switch Group-assignment featuresMatrix post-switch Mono-assignment switchGroup-master features Output level-control 100mm fader MTX switch recessed Module swap featuresMode switch recessed FOH group LEDGroup rear-panel connectors Vca masters Illuminated mute-switchesSolo switches 100mm fadersLeft/right/mono to matrix on-switch Output mute safe switchLeft, right and mono peak and signal-present Leds Matrix-post switchMute safe Input fader blockAct LED µ-mute Act LED VCAStereo-matrix features Stereo matrix / aux out moduleExternal-in left and right signal-level to matrix Stereo matrix output-level control Stereo matrix solo-switchMtx to aux Stereo matrix output-balance controlDual-aux output features Talkback preset-switch One odd channel, one even channel 100mm output fader One per odd channel, one per even channelSolo switch Oscillator features Master modules-M1, M2Meter-view features Meters-A/meters-B switch bankAlternate output features Provides an area to label the alternate outputs usage Talkback master features Link headphone/intercom switch Intercom interconnect featuresConsole-to-intercom level and switch Comms levelMonitor output features Dim On-switchSum 100mm fader level-controlLCR output-monitoring Headphone output featuresLeft-/right-output switch 100mm headphone level-control Solo system features Page Micro panel features Micro mute systemManual mute-bank select Channel fader features ButtonVCA LED on module Normal operation mode Micro operationSelect Scene to edit Edit/preview rapid recall Edit/ViewExiting Edit Mode Other ways to exit Edit ModeUtility Mode UtilitiesGeneral Controls Clear UtilitiesShow Control Micro UtilitiesGeneral Controls Scene Resettingthe Micro Page V12 rear views Page V12 rear views
Related manuals
Manual 24 pages 8.07 Kb

V12 specifications

The Peavey V12 is a remarkable guitar amplifier that has gained a reputation for its versatility, punchy sound, and reliability. Aimed at guitarists across various genres, the V12 combines advanced technologies with user-friendly features, making it an appealing option for both amateur and professional musicians.

One of the standout features of the Peavey V12 is its power and performance. This amplifier delivers an impressive 120 watts of power, ensuring that it can handle large gigs and rehearsals with ease. Its dual gain structure allows players to explore a wide range of tone options, offering both clean sounds and high-gain distortion. This adaptability makes the V12 suitable for everything from blues to rock and metal.

The V12 boasts Peavey's patented TransTube technology, which emulates the warm, dynamic sound of tube amplifiers. This innovative technology provides a rich tonal palette, delivering the best of both worlds – the warmth of analog sound with the reliability of solid-state performance. Furthermore, the amp comes equipped with a three-channel configuration, giving users access to clean, crunch, and lead sounds at the push of a button. This makes it easy to switch between settings during live performances.

In addition to its tonal options, the Peavey V12 offers comprehensive EQ controls, including treble, mid, and bass adjustments. This allows guitarists to fine-tune their sound to suit their specific preferences and playing styles. The presence and resonance controls further enhance tonal shaping, enabling players to achieve a robust sound that cuts through the mix.

Another notable characteristic of the V12 is its durable construction. Built with high-quality materials, this amp can withstand the rigors of touring, making it a reliable choice for musicians on the road. The lightweight design also adds to its ease of transport, ensuring that musicians can take their sound anywhere.

Additional features include built-in reverb, allowing users to add depth to their tone, and a headphone output for silent practice. The amp is also compatible with footswitching, which gives players added control during performances.

In conclusion, the Peavey V12 is an exceptional amplifier that blends power, versatility, and cutting-edge technology. With its extensive sound-shaping capabilities and robust construction, it stands out as an ideal choice for guitarists seeking quality and performance in one package. Whether for practice, recording, or live performances, the V12 is designed to meet the demands of contemporary musicians.
Top Page Image Contents