Peavey SRM Series owner manual Filtering, Notch Filter Bank

Page 6

Filtering

Monitor Sends 1 through 8 have a bank of two sweepable notch filters (Hi and Low frequency section) and a Low Cut Filter. Because the majority of feedback problems occur within the monitor system, our advice is that you become very familiar with this feature. Filters, like any other form of equalization, are an aid. They cannot substitute the correct use/placement of high-quality micro- phones and speakers.

A Notch Filter is used to single out a problem area within the frequency spectrum and reduce the level in that one area by a certain amount. The frequency that you select is the frequency to be reduced the most.

A Low Cut Filter, cuts the signal content off (roll-off) at a desired frequency. This is great for eliminating low frequency rumble on stage. Since low frequencies have less directivity than do high frequencies, it is often unnecessary to have very low frequency content in the monitor mix. This becomes apparent when attempting to play an acoustic guitar on a high-volume stage. The acoustic cavity of the guitar has a tendency to resonate with the low frequency content of the monitor mix. When that happens a feedback occurs in the low frequency portion of the spectrum. Much of that portion can be eliminated with the Low Cut Filter, thus reducing the chance of feedback. Once again, this section applies to Monitor Sends 1-8 only.

NOTE: See SRM specifications (page 20) for filter details.

10

9

10

9

8

11

Notch Filter Bank:

8.LED Tuning Indicators: These three yellow LEDs indicate which direction to adjust the Frequency Control (#9) to properly tune the filter: left (down), center, right (up). When all three LED’s are illuminated you have found the problem frequency.

9.Frequency Control: This control adjusts the center frequency of the notch The frequency range of this control is .5 kHz to 10 kHz (High Frequency) and

.1 kHz to 4 kHz (Low Frequency.). With the Depth Control (#10) set to 0 dB, adjust this control according to the LED Tuning Indicators (#8). Once the frequency is found, adjust the Depth Control (#10) from 0 dB to its optimum position.

10.Depth Control: This control adjusts the amount of attenuation for the selected frequency (#9). Although the control offers -15 dB to 0 dB of attenua- tion, you will want to set this control as close to the 0 dB position as possible without experiencing feedback. This will insure you the flatest frequency response from your board with the least amount of feedback, a happy medium if you will. Before attempting to find the feedback frequency (#9), adjust the Depth Control to 0 dB. Once the frequency is found you will want to slowly adjust it towards -15 dB until the feedback has subsided. If there is no feedback on a particular Monitor Send, its Depth Control should be set to 0 dB. It will not matter what the Frequency Control (#9) is set to under these conditions.

NOTE: The High and Low Notch Filters have a .5 Hz to 4 kHz overlap

(3 octaves). You will want to avoid accidentally setting both filters to the same center frequency and achieving double attenuation.

11.Low Cut Filter Control: This control adjusts the corner frequency of the Low Cut Filter. Basically, the filter is on all of the time but unless this control is

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents M S E R I E S Page SRM Features SRM Series Sound Reinforcement Monitor ConsolePower and Lights Description by Section IndexMonitor Master Section PatchingFiltering Notch Filter BankListening and Controlling Individual Input Channels Input PatchingPre EQ. The jack is wired Tip=Send, Ring=Return, Channel Filtering/EQ Meters/ControllingINTERCOM/TALKBACK IntercomPage IN’S and OUT’S TalkbackPage SRM Wiring Diagram SRM Wiring Diagram Output SectionSpecifications Input Specifications SRMFrequency Response Output SpecificationsGain Total Harmonic Distortion THDHum and Noise Common Mode Rejection Ratio C.M.R.R Mic inputDimensions H x W x D 9.5 x 43.5 x Crosstalk @ 1 kHz Hz to 20 kHz ChannelChannel EQ and LC Filter Master Notch and Varible LC FilterChannel Mid Sweep SRM Consola de monitoreo reforzadora de sonido Funciones de la consola SRMÍdice de secciones Alimentación E IluminaciónControl Maestro DE Monitoreo Conexiones accesoriasFiltrado Banco de filtros de muescaVisualización y control Canales DE Entrada Individuales Conexiones accesorias de entradaPage Filtrado/ecualización del canal Monitoreo/controlINTERFONO/INTERCOMUNICADOR Interfono Entradas Y Salidas IntercomunicadorPage SRM Console de mixage pour sytème de retours Caractéristiques de la SRMIndex des sections Section Master MonitorEntrées-sorties Filtrage Notch FilterContrôle et surveillance Canaux D’ENTRÉE Individuels ConnexionsPage Contrôle INTERCOM/TALKBACK Entrées ET Sorties Deutch SRM Sound Reinforcement MonitorkonsoleBeschreibung nach Sektion Index Strom UND BeleuchtungFilterung Abhörung und Controlling Page Individuelle Eingangskanäle Page Meters/Controlling Intercom EIN- UND Ausgänge Page Peavey Electronics Corporation Limited Warranty Important Safety Instructions 80304467
Top Page Image Contents