Fostex MR-8 owner manual Synchronization using Midi clock

Page 78

MR-8 Owner’s Manual

The current option (the default is "Off") flashes. You can now select the desired one from among three options below.

•Off: No signal is output from the [MIDI OUT] connector.

•CLK: MIDI clock with Song Position Pointer is output from the [MIDI OUT] connector.

•MTC: MIDI time code is output from the [MIDI OUT] connector.

4)Use the [CURSOR /] keys to select "MTC", then press the [ENTER] key.

"Midi Sync Out" setting is now effective, while "Midi Sync Out" is highlighted on the screen.

5)Use the [CURSOR ] key to highlight "MTC FrameRate", then press the [ENTER] key.

The current option (the default is "25") flashes. You can now select a frame rate from among four options: "24", "25", "30nd" and "30df".

6)Use the [CURSOR /] keys to select the desired frame rate, then press the [ENTER] key.

The frame rate setting is now effective, while "MTC FrameRate" is highlighted on the screen.

7)Press the [MENU] key to exit the menu mode.

Synchronization using MIDI clock

The following describes how to synchronize a sequencer to the MR-8 using MIDI clock. Use this method if the sequencer does not support MTC (MIDI Time code)

<Notes>

•To synchronize a sequencer to the MR-8 using MIDI clock, you have to make the signature/ tempo map in the MR-8. The MIDI clock is output according to the signature/tempo map in the MR-8. When starting recording, synchronize the sequencer to the MIDI clock fed from the MR-8.

•Generally, a sequencer supporting MIDI song position pointer as well as MIDI clock can synchronize to the MR-8 when you start playback of the MR-8 from the middle of a song. It locates the current song position and chase the MR-8. However, note that some sequencer may not synchronize to the MR-8.

Connection

As with the connection for MTC synchronization, connect the [MIDI OUT] connector of the MR-8 to the [MIDI IN] connector of an external MIDI sequencer using a MIDI cable.

Settings of the MR-8 and MIDI sequencer

1)In the "System" menu of the menu mode, set the "Midi Sync Out" item to "Clk".

See "MIDI sync/MTC frame rate settings" above about how to set.

2)In the "Song" menu of the menu mode, create the signature/tempo map by setting "Signature Map" and "Tempo Map" appropriately.

See "Using the rhythm guide function" on page 79 for details about how to set these items.

3)Enable the external MIDI sequencer to synchronize to MIDI clock.

See the operation manual of the sequencer for details.

4)Press the [PLAY] key of the MR-8 to start playback.

The sequencer also starts playback while synchronizing to the MR-8.

78

Page 77 Page 79
Image 78
Page 77 Page 79
Contents Digital Multitracker 8588 018 100Safety Instructions Table of Contents 100 101MR-8 Main features About power supply IntroductionPrecautions upon handling the MR-8 About copyrightsAbout damages Recording method Song modeBasics of the MR About songBar/Beat/Clk Time baseABS time Time counterRemain display Input monitor and repro monitorTrim control Names and Functions Input a connectorsInput B connectors Top panel left partPhones VOL control REVERB/DELAY Time controlPhones jacks 1 Effect keysTop panel right part UNDO/REDO /Y Z 9 entry key Counter Reset / P Q R 6 entry keyPlay Mode / a B C 1 entry key Time Base Select / V W X 8 entry keyRear panel Bottom panel Battery compartmentSide panel Card slot Midi OUT jackHow to remove a CompactFlashTM card How to insert a CompactFlashTM cardAbout recording medium Inserting batteries About the powerConnecting the AC adaptor Turning on the unitLow battery display Turning off the powerTurning on the LCD display backlight Listening the demo song Tips Listening to the demo song againPress the Menu key to enter the menu mode Preparation of a CompactFlashTM car dWhile S01 Fostexfever is highlighted, press the Enter key How to enter characters Character entry keysEntry example Preparation for recording onto a new card Press the Menu key to quit the menu modeTurn on the MR-8 power Correction and deletionCreating a song Select the song mode using the Cursor or Cursor keyCreating a song/selecting a song While Select Song is highlighted, press the Enter keySelecting a desired song TipWhile Card Format is highlighted, press the Enter key Formatting a cardWhile System is highlighted, press the Enter key Press the Enter keyConnections Model AD-12ADisplay Home screenAdjusting the display contrast Selecting a time baseMenu screen MR -8 recording basics Recording onto a mono trackRecording onto stereo track About simulation effect Input level settingDistortion setting Insert effectsRecording onto a single track Preparation for recordingPlaying back the recorded track Undo/redoStarting recording Preparation for recording Set the Input a Select switch to MIC/LINERecording onto two tracks Press the REC Select key for track 5/6Starting recording Playing back the recorded tracksPunch in/out using the keys on the top panel Punch in/out using the footswitchPunch in/out Auto punch in/out Setting the punch-in and punch-out pointsHow to make auto punch in/out mode active RehearsalPress the Play key to start playback of the song Actual auto punch in/outAbout part Locate the recorder to the point before the punch- in pointMic simulation effects Using effectsUsing the insert effects for recording Amp simulation effectsSelecting an effect type Selecting a delay typeUsing the reverb or delay Details of each effect typeAdjusting the delay/reverb time Adjusting the effect send levelsSignal flow from a track to the effector Using the mastering effects Selecting the desired effect typeDetails about each mastering effect type Bouncing tracks Example of track bouncing7/8 mode Signal flow of track bouncingSelecting the bounce mode 5/6 modeRehearsal of track bounce Panning control Checking the bounced signals on trackActual track bounce Auto punch in/out of track bouncingExporting bounced data to a personal computer Through 4 for recordingMixdown Analog mixdownUse the Master fader of the MR-8 to adjust the output level Digital mixdownAfter finishing recording, stop both recorders Tip Playback cueing Playback functionsBasic playback Playback between Locate a and B pointsAuto return mode Selecting a play modeAuto play mode Loop modeLoop function in auto punch in/out mode Locate ABS Zero function Resetting the counterLocate functions Locate REC END functionStoring a Locate a point Locating to counter zeroStoring a locate point Locating to the Locate a or Locate B pointStoring a Locate B point LocatingWhen System is highlighted, press the Enter key Setting the pre-roll/post- rollHow to set the pre-roll/post-roll time After selecting the pre-roll time, press the Enter keyBar / 1 / 46 clk 1 bar / 1 / 00 clk Setting the beat resolutionHow to set the beat resolution Bar / 4 / 51 clk 3 bar / 1 / 00 clkCreating a new song Press the Menu key to exit the menu modeEditing a song Selecting a desired songEditing a song name After entering the name, move the cursor toKey, then press the Enter key Deleting an unnecessary song Protecting a song TipsUse the Cursor / keys to select On, and press the Enter key Deleting the unnecessary file in a song Track editing Undo/redo of track editingWhile Erase Track is highlighted, press the Enter key Copying/pasting whole track data Press the Enter key Moving whole track data Use the Cursor / keys to select source tracks to be movedExchange whole track data Flashing Part editing Erasing a desired part Copying to the clipboard Use the Cursor / keys to select the tracksPasting clipboard data Use the Cursor / keys to select the desired tracksWhile Paste Part is highlighted, press the Enter key Then press the Enter key Moving the desired part to the other tracks Use the Cursor / keys to select the move source tracks Exchange parts between tracks Use the Cursor / keys to select the exchange source tracksPress the Enter key Synchronization using MTC Midi sync/MTC frame rate settingsSettings of the MR-8 and Midi sequencer Synchronizing with MidiSynchronization using Midi clock Using the rhythm guide function Setting the signature mapCreating the signature/tempo map Use the Cursor / keys to enter Use the Cursor key to flash 4/4 for Sig. settingChanging the bar number or signature Use the Cursor / keys to enter 3/4Deleting an unnecessary bar/signature setting Changing the bar offsetTo exit the menu mode, press the Menu key 180 Creating the tempo mapFirst beat in bar 120 Third beat in bar First beat in bar 120Use the Cursor key to flash 1 for Beat setting Use the Cursor key to flash 120 for Tempo settingDeleting an unnecessary tempo setting Editing the tempo mapUse the Cursor / keys to enter a desired tempo value Setting the click level Procedure of file conversion WAV file conversionEnabling the file conversion Editing a file name Xporting data to a personal computer Connection to a personal computerExporting a WAV file to a personal computer Important notePress the Menu key to exit the menu mode Tip Initialized item Default setting Initializing the MRTrouble TroubleshootingTroubles for recording Is the Record key flashing and does Light on the display?Is shown on the screen? Troubles for playbackIs the track fader for the playback track brought up? Are the punch-in and punch-out points set correctly?Troubles for power supply Troubles for effectOther troubles Inputs/Outputs MR- 8 specificationsPin assignment of XLR connectors Record/playbackPhysical dimensions Block diagramWhen using the normal mode When using the bounce mode 1-4 5/6 mode When using the bounce mode 1-6 7/8 modeMidi Implementation Chart Model MR-8Index 100RP Stereo Headphone Optical Cable Powered near field studio Optional accessariesStereo Headphone Foot switch Personal Monitor MonitorDeclaration of EC Directive 376785
Top Page Image Contents