Fostex MR-8 owner manual Exporting a WAV file to a personal computer, Important note

Page 89

MR-8 Owner’s Manual

Exporting a WAV file to a personal computer

The following describes the procedure for export- ing a WAV file to a Windows ME computer.

<Important note>

Converted stereo WAV files are located in the "2 MIX" folder in the Song folder, as shown below. So you can export only a stereo WAV file in the "2 MIX" folder (indicated by an ar- row).

Note that, if you export a WAV file which is located in a folder other than the "2 MIX" folder, the MR-8 may malfunction.

Song

2 MIX

1)Turn on the power of the personal computer and the MR-8.

2)Press the [MENU] key to enter the menu mode.

The MENU screen is shown in which "System" is highlighted.

3)Highlight "USB" using the [CURSOR ] key, then press the [ENTER] key (or the [CURSOR ] key).

The MR-8 enters the USB mode, while the display shows the lower screen below.

#####001.wav

#####002.wav

#####003.wav

*********.wav

<Note>

While the MR-8 is in the USB mode, no keys except the [STOP] key are ineffective. Press- ing the [STOP] key exits the USB mode.

#####008.wav

4)Connect the MR-8 to a personal computer using a USB cable.

5)Open "My computer" on the computer screen.

You see the "Removable disc" drive added on the computer. The first time you connect the MR-8, the device driver is installed automatically.

6)Open the "Removable disc" drive added, and select a desired stereoWAV file in the "2 MIX" folder in a desired song folder, then copy to the computer.

When you open the "Removable disc" drive added, the contents of the card inserted to the MR-8 are shown, in which you can see all the song folders.

89

Image 89

Contents 8588 018 100 Digital MultitrackerSafety Instructions Table of Contents 101 100Introduction MR-8 Main features About power supplyAbout damages Precautions upon handling the MR-8About copyrights Basics of the MR Song modeRecording method About songABS time Time baseBar/Beat/Clk Time counterTrim control Remain displayInput monitor and repro monitor Input B connectors Input a connectorsNames and Functions Top panel left partPhones jacks 1 REVERB/DELAY Time controlPhones VOL control Effect keysTop panel right part Play Mode / a B C 1 entry key Counter Reset / P Q R 6 entry keyUNDO/REDO /Y Z 9 entry key Time Base Select / V W X 8 entry keyRear panel Side panel Battery compartmentBottom panel Card slot Midi OUT jackAbout recording medium How to remove a CompactFlashTM cardHow to insert a CompactFlashTM card Connecting the AC adaptor About the powerInserting batteries Turning on the unitTurning on the LCD display backlight Low battery displayTurning off the power Tips Listening to the demo song again Listening the demo songWhile S01 Fostexfever is highlighted, press the Enter key Press the Menu key to enter the menu modePreparation of a CompactFlashTM car d Entry example How to enter charactersCharacter entry keys Turn on the MR-8 power Press the Menu key to quit the menu modePreparation for recording onto a new card Correction and deletionCreating a song/selecting a song Select the song mode using the Cursor or Cursor keyCreating a song While Select Song is highlighted, press the Enter keyTip Selecting a desired songWhile System is highlighted, press the Enter key Formatting a cardWhile Card Format is highlighted, press the Enter key Press the Enter keyModel AD-12A ConnectionsHome screen DisplayMenu screen Adjusting the display contrastSelecting a time base Recording onto stereo track MR -8 recording basicsRecording onto a mono track Distortion setting Input level settingAbout simulation effect Insert effectsPreparation for recording Recording onto a single trackStarting recording Playing back the recorded trackUndo/redo Recording onto two tracks Set the Input a Select switch to MIC/LINEPreparation for recording Press the REC Select key for track 5/6Playing back the recorded tracks Starting recordingPunch in/out Punch in/out using the keys on the top panelPunch in/out using the footswitch How to make auto punch in/out mode active Setting the punch-in and punch-out pointsAuto punch in/out RehearsalAbout part Actual auto punch in/outPress the Play key to start playback of the song Locate the recorder to the point before the punch- in pointUsing the insert effects for recording Using effectsMic simulation effects Amp simulation effectsUsing the reverb or delay Selecting a delay typeSelecting an effect type Details of each effect typeSignal flow from a track to the effector Adjusting the delay/reverb timeAdjusting the effect send levels Details about each mastering effect type Using the mastering effectsSelecting the desired effect type Example of track bouncing Bouncing tracksSelecting the bounce mode Signal flow of track bouncing7/8 mode 5/6 modeRehearsal of track bounce Actual track bounce Checking the bounced signals on trackPanning control Auto punch in/out of track bouncingThrough 4 for recording Exporting bounced data to a personal computerAnalog mixdown MixdownAfter finishing recording, stop both recorders Tip Use the Master fader of the MR-8 to adjust the output levelDigital mixdown Basic playback Playback functionsPlayback cueing Playback between Locate a and B pointsAuto play mode Selecting a play modeAuto return mode Loop modeLoop function in auto punch in/out mode Locate functions Resetting the counterLocate ABS Zero function Locate REC END functionStoring a locate point Locating to counter zeroStoring a Locate a point Locating to the Locate a or Locate B pointLocating Storing a Locate B pointHow to set the pre-roll/post-roll time Setting the pre-roll/post- rollWhen System is highlighted, press the Enter key After selecting the pre-roll time, press the Enter keyHow to set the beat resolution Setting the beat resolutionBar / 1 / 46 clk 1 bar / 1 / 00 clk Bar / 4 / 51 clk 3 bar / 1 / 00 clkEditing a song Press the Menu key to exit the menu modeCreating a new song Selecting a desired songKey, then press the Enter key Editing a song nameAfter entering the name, move the cursor to Deleting an unnecessary song Use the Cursor / keys to select On, and press the Enter key Protecting a songTips Deleting the unnecessary file in a song While Erase Track is highlighted, press the Enter key Track editingUndo/redo of track editing Copying/pasting whole track data Press the Enter key Use the Cursor / keys to select source tracks to be moved Moving whole track dataExchange whole track data Flashing Part editing Erasing a desired part Use the Cursor / keys to select the tracks Copying to the clipboardWhile Paste Part is highlighted, press the Enter key Pasting clipboard dataUse the Cursor / keys to select the desired tracks Then press the Enter key Moving the desired part to the other tracks Use the Cursor / keys to select the move source tracks Use the Cursor / keys to select the exchange source tracks Exchange parts between tracksPress the Enter key Settings of the MR-8 and Midi sequencer Midi sync/MTC frame rate settingsSynchronization using MTC Synchronizing with MidiSynchronization using Midi clock Creating the signature/tempo map Using the rhythm guide functionSetting the signature map Changing the bar number or signature Use the Cursor key to flash 4/4 for Sig. settingUse the Cursor / keys to enter Use the Cursor / keys to enter 3/4To exit the menu mode, press the Menu key Deleting an unnecessary bar/signature settingChanging the bar offset First beat in bar 120 Creating the tempo map180 Third beat in bar First beat in bar 120Use the Cursor key to flash 120 for Tempo setting Use the Cursor key to flash 1 for Beat settingUse the Cursor / keys to enter a desired tempo value Deleting an unnecessary tempo settingEditing the tempo map Setting the click level Enabling the file conversion Procedure of file conversionWAV file conversion Editing a file name Connection to a personal computer Xporting data to a personal computerImportant note Exporting a WAV file to a personal computerPress the Menu key to exit the menu mode Tip Initializing the MR Initialized item Default settingTroubles for recording TroubleshootingTrouble Is the Record key flashing and does Light on the display?Is the track fader for the playback track brought up? Troubles for playbackIs shown on the screen? Are the punch-in and punch-out points set correctly?Other troubles Troubles for power supplyTroubles for effect Pin assignment of XLR connectors MR- 8 specificationsInputs/Outputs Record/playbackWhen using the normal mode Physical dimensionsBlock diagram When using the bounce mode 1-6 7/8 mode When using the bounce mode 1-4 5/6 modeModel MR-8 Midi Implementation Chart100 IndexStereo Headphone Foot switch Personal Monitor Optional accessariesRP Stereo Headphone Optical Cable Powered near field studio MonitorDeclaration of EC Directive 376785