Edirol V-4 owner manual Avis

Page 2

For the U.K.

IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.

BLUE: NEUTRAL

BROWN: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.

For EU Countries

This product complies with the requirements of European Directive 89/336/EEC.

For the USA

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation.

Unauthorized changes or modification to this system can void the users authority to operate this equipment. This equipment requires shielded interface cables in order to meet FCC class B Limit.

For Canada

NOTICE

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

AVIS

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

2

Image 2
Contents Page Avis Page Page Maintenance Power SupplyPlacement Additional PrecautionsOther important notes About turning the power onAbout specifications Contents Midi implementation Index Welcome Features What is V-LINK? LinkBefore you begin Check the included itemsNames of things and what they do Rear PanelFront Panel Before you begin About Ground Terminal Unsuitable places for connectionConnecting peripheral devices Typical connection exampleVideo signal flow Turning the power off Turning the power on/offTurning the power on Checking the output to the preview monitor Checking the inputs and outputsChecking the final output About the display on preview monitor Conceptual diagram of the Memory dial About the Memory dial MemorySwitching two images Switching by CutSwitching with dissolve Switching with WipeUsing fade-to-white or fade-to-black Using Picture In Picture to composite images Compositing two imagesUsing Chroma Key to composite images Using Luminance Key to composite images Compositing two images Compositing two images Changing the color of the image Applying the Negative effectApplying the Colorize effect Changing the color of the image Changing the motion of the image Applying strobe motionApplying the Multi or Mirror effects Applying the Multi effectApplying the Mirror effect Using the tap TAP function to switch images Switching in synchronization with musicUsing BPM sync to switch images Switching in synchronization with music Applying an effect on the music Using BPM sync to apply an effectUsing the tap TAP function to apply an effect Editing the front panel assignments Enter Button EnterEditing the front panel assignments Changing the assignment of the mix button MIX Changing the assignment of the wipe button Wipe Changing the assignment of the EFX button EFX Editing the front panel assignments Changing the assignment of the output fade dial Output FadeEditing the front panel assignments Editing the front panel assignments Editing the front panel assignments Changing the assignment of the BPM sync button BPM Sync Editing the front panel assignments Editing the front panel assignments Protecting the memory Copying or exchanging memories Recalling the factory settings Editing the front panel assignments Using V-LINK to control Control the V-4 from an external deviceUsing Midi to control Using V-LINKDV-7PR Midi settings Setting the Midi receive channel Midi Rx Channel Making other Midi settings Midi Setup Making various settings Making various settings Calibrating the video fader Calibrating the video fader Using the V-4 in Presentation mode What is Presentation mode?Switching to Presentation mode Presentations using two screens with Picture In PictureUsing the V-4 in Presentation mode Switching between Ntsc and PAL Changing the video fader orientation Changing the video fader orientation Troubleshooting Operating the video fader does not switch the imageMenu List Menu List255 Effects-A Mem2-8 Efx1 Efx2 Efx3 Efx4 Effects-B Output Fade Mem2-8 BPM Sync Mem 2-8 Mode Midi Setup Midi Tx Channel Utility Mode Preview Auto Speed Main specifications Video inputMain specifications Dimensions Examples of using Using the V-4 at an eventUsing the V-4 at a concert or VJ performance DV-7PRUsing the V-4 at a presentation DVDVideo output Preview Midi control Projector Midi implementation Midi messages received at MidiMidi implementation Midi messages transmitted from Midi OUT Midi implementation Midi Implementation Parameter Address Map Clip Control Preference Appendices Factory Setting of V-LINK Midi Implementation Chart Index PALInformation 03019190 ’03-01-C2-11KS