Edirol V-4 owner manual About Ground Terminal, Unsuitable places for connection

Page 16

Before you begin

26.BPM sync button (BPM SYNC) (see p. 39)

Press this button if you want to switch images or turn effects on/off in synchronization with the BPM.

27.Video fader (T-bar type)

This is a T-bar type video fader. You can use it to switch between channels A and B, or to adjust the keying level, etc. According to your preference, you can change the orientation 90 degrees from up and down to left to right. For details on how to change the orientation, refer to p. xxx.

28.Channel B effect buttons (EFFECTS)

These buttons apply effects to the image of video mixer channel B. With the factory settings, the buttons are assigned (from top to bottom) the Mirror, Chroma Key, Luminance Key, and P in P (Picture In Picture) effects. You may edit the settings to assign different effects to these buttons if desired.

29.Channel B effect control dial (CONTROL)

This dial lets you smoothly control a parameter of an effect that is being applied to the image of channel B. The dial will adjust an effect parameter of the effect button that is blinking.

30.Channel B transformer button (TRANSFORMER) (see p. 23)

This button lets you switch between channels A and B without using the video fader.

About Ground Terminal

In some cases, depending on the environment in which the unit is installed, the surface of the panel may sometimes feel rough and grainy. This is due to an infinitesimal electrical charge, which is absolutely harmless. However, if you are concerned about this, connect ground terminal (see figure) with an external ground. When the unit is grounded, a slight noise may result, depending on the particulars of your installation. If you are unsure of the connection method, contact nearest Edirol Service Center, or authorized Edirol/Roland distributor, as listed on the “Information” page.

Ground Terminal

Unsuitable places for connection

Water pipes (may result in shock or electrocution)

Gas pipes (may result in fire or explosion)

Telephone-line ground or lightning rod (may be dangerous in the event of lightning)

16

Image 16
Contents Page Avis Page Page Power Supply PlacementMaintenance Additional PrecautionsAbout specifications About turning the power onOther important notes Contents Midi implementation Index Welcome Features What is V-LINK? LinkBefore you begin Check the included itemsNames of things and what they do Rear PanelFront Panel Before you begin About Ground Terminal Unsuitable places for connectionConnecting peripheral devices Typical connection exampleVideo signal flow Turning the power on Turning the power on/offTurning the power off Checking the final output Checking the inputs and outputsChecking the output to the preview monitor About the display on preview monitor Conceptual diagram of the Memory dial About the Memory dial MemorySwitching two images Switching by CutSwitching with dissolve Switching with WipeUsing fade-to-white or fade-to-black Using Picture In Picture to composite images Compositing two imagesUsing Chroma Key to composite images Using Luminance Key to composite images Compositing two images Compositing two images Changing the color of the image Applying the Negative effectApplying the Colorize effect Changing the color of the image Changing the motion of the image Applying strobe motionApplying the Multi or Mirror effects Applying the Multi effectApplying the Mirror effect Using BPM sync to switch images Switching in synchronization with musicUsing the tap TAP function to switch images Switching in synchronization with music Using the tap TAP function to apply an effect Using BPM sync to apply an effectApplying an effect on the music Editing the front panel assignments Enter Button EnterEditing the front panel assignments Changing the assignment of the mix button MIX Changing the assignment of the wipe button Wipe Changing the assignment of the EFX button EFX Editing the front panel assignments Changing the assignment of the output fade dial Output FadeEditing the front panel assignments Editing the front panel assignments Editing the front panel assignments Changing the assignment of the BPM sync button BPM Sync Editing the front panel assignments Editing the front panel assignments Protecting the memory Copying or exchanging memories Recalling the factory settings Editing the front panel assignments Using V-LINK to control Control the V-4 from an external deviceUsing Midi to control Using V-LINKDV-7PR Midi settings Setting the Midi receive channel Midi Rx Channel Making other Midi settings Midi Setup Making various settings Making various settings Calibrating the video fader Calibrating the video fader Using the V-4 in Presentation mode What is Presentation mode?Switching to Presentation mode Presentations using two screens with Picture In PictureUsing the V-4 in Presentation mode Switching between Ntsc and PAL Changing the video fader orientation Changing the video fader orientation Troubleshooting Operating the video fader does not switch the imageMenu List Menu List255 Effects-A Mem2-8 Efx1 Efx2 Efx3 Efx4 Effects-B Output Fade Mem2-8 BPM Sync Mem 2-8 Mode Midi Setup Midi Tx Channel Utility Mode Preview Auto Speed Main specifications Video inputMain specifications Dimensions Examples of using Using the V-4 at an eventUsing the V-4 at a concert or VJ performance DV-7PRUsing the V-4 at a presentation DVDVideo output Preview Midi control Projector Midi implementation Midi messages received at MidiMidi implementation Midi messages transmitted from Midi OUT Midi implementation Midi Implementation Parameter Address Map Clip Control Preference Appendices Factory Setting of V-LINK Midi Implementation Chart Index PALInformation 03019190 ’03-01-C2-11KS