Edirol V-4 owner manual About turning the power on, About specifications, Other important notes

Page 6

When circuit board installation is complete, double-check your work.

(French)

Quand l’installation de la carte de circuits imprimés est terminée, revérifiez si tout est bien installé.

*In some cases, depending on the environment in which the unit is installed, the surface of the panel may sometimes feel rough and grainy. This is due to an infini- tesimal electrical charge, which is absolutely harmless. However, if you are concerned about this, connect the ground terminal (see figure on p.16) with an external ground. When the unit is grounded, a slight noise may appear, depending on the particulars of your installation. If you are unsure of the connection method, contact the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page.

Unsuitable places for connection

-Water pipes (may result in shock or electrocution)

-Gas pipes (may result in fire or explosion)

-Telephone-line ground or lightning rod (may be dangerous in the event of lightning)

About turning the power on

Once the connections have been completed (p. 19), turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to other devices.

This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally.

About specifications

*In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.

Other important notes

The explanations in this manual include illustrations that depict what should typically be shown by the display. Note, however, that your unit may incorporate a newer, enhanced version of the system (e.g., includes newer software), so what you actually see in the display may not always match what appears in the manual.

• Security Slot ( ) http://www.kensington.com/

This product is compatible with regular NTSC or PAL video signal. In case irregular signal is input, it may obstruct stabile operation of this product.

It is possible on this product to create video sequence with extremely quick switching or ON/OFF of effects. Depending on your physical conditions, such video sequence may cause medical problem like headache etc. It is prohibited to create video sequence that may cause such problem. Roland or Edirol is not responsible to any medical problem of yourselves or audiences/spectators caused by such video sequence.

6

Image 6
Contents Page Avis Page Page Maintenance Power SupplyPlacement Additional PrecautionsAbout turning the power on About specificationsOther important notes Contents Midi implementation Index Welcome Features What is V-LINK? LinkBefore you begin Check the included itemsNames of things and what they do Rear PanelFront Panel Before you begin About Ground Terminal Unsuitable places for connectionConnecting peripheral devices Typical connection exampleVideo signal flow Turning the power on/off Turning the power onTurning the power off Checking the inputs and outputs Checking the final outputChecking the output to the preview monitor About the display on preview monitor Conceptual diagram of the Memory dial About the Memory dial MemorySwitching two images Switching by CutSwitching with dissolve Switching with WipeUsing fade-to-white or fade-to-black Using Picture In Picture to composite images Compositing two imagesUsing Chroma Key to composite images Using Luminance Key to composite images Compositing two images Compositing two images Changing the color of the image Applying the Negative effectApplying the Colorize effect Changing the color of the image Changing the motion of the image Applying strobe motionApplying the Multi or Mirror effects Applying the Multi effectApplying the Mirror effect Switching in synchronization with music Using BPM sync to switch imagesUsing the tap TAP function to switch images Switching in synchronization with music Using BPM sync to apply an effect Using the tap TAP function to apply an effectApplying an effect on the music Editing the front panel assignments Enter Button EnterEditing the front panel assignments Changing the assignment of the mix button MIX Changing the assignment of the wipe button Wipe Changing the assignment of the EFX button EFX Editing the front panel assignments Changing the assignment of the output fade dial Output FadeEditing the front panel assignments Editing the front panel assignments Editing the front panel assignments Changing the assignment of the BPM sync button BPM Sync Editing the front panel assignments Editing the front panel assignments Protecting the memory Copying or exchanging memories Recalling the factory settings Editing the front panel assignments Using V-LINK to control Control the V-4 from an external deviceUsing Midi to control Using V-LINKDV-7PR Midi settings Setting the Midi receive channel Midi Rx Channel Making other Midi settings Midi Setup Making various settings Making various settings Calibrating the video fader Calibrating the video fader Using the V-4 in Presentation mode What is Presentation mode?Switching to Presentation mode Presentations using two screens with Picture In PictureUsing the V-4 in Presentation mode Switching between Ntsc and PAL Changing the video fader orientation Changing the video fader orientation Troubleshooting Operating the video fader does not switch the imageMenu List Menu List255 Effects-A Mem2-8 Efx1 Efx2 Efx3 Efx4 Effects-B Output Fade Mem2-8 BPM Sync Mem 2-8 Mode Midi Setup Midi Tx Channel Utility Mode Preview Auto Speed Main specifications Video inputMain specifications Dimensions Examples of using Using the V-4 at an eventUsing the V-4 at a concert or VJ performance DV-7PRUsing the V-4 at a presentation DVDVideo output Preview Midi control Projector Midi implementation Midi messages received at MidiMidi implementation Midi messages transmitted from Midi OUT Midi implementation Midi Implementation Parameter Address Map Clip Control Preference Appendices Factory Setting of V-LINK Midi Implementation Chart Index PALInformation 03019190 ’03-01-C2-11KS