Vermont Casting DVT38IN installation instructions Min 610mm

Page 24

Chateau™

Attic Installation

Nails (4)

Firestop Spacer

Joist

Ceiling Installation

Joist

Firestop Spacer

Elbow Strap		Support Structure
Elbow Strap		Support Structure

Elbow Strap (must be tight)

Ceiling Hole

Framing

Angled Strap

Angled Firestop

Chimney Support Strap (must be tight)

FP270/271

Fig. 33 Attach straps to a structural framing member.

Nails (4)

Fig. 31 Installing ﬁrestop spacer.

Attic

Insulation

Shield

FP593

Min.

2' (610mm)

Nails (4 Re- quired)

Attic Joist

	Base
Ceiling	Flanges	FP263
Ceiling

Fig. 32 Attic shield installation.

CFM190

Fig. 34 Minimum termination to roof clearance.

If an attic is above ceiling level an AIS-SK (Attic Insulation Shield) must be installed.

The enlarged ends of the vent section always face downward.

24

20011956

Image 24

Contents INSTALLER/CONSUMER Safety Information What to do if YOU Smell GASTable of Contents Installation & Operating Instructions Certiﬁed ToPlease Review the Following Carefully Requirements for the Commonwealth of Massachusetts Clear of ALL ObstructionsGas Equipment Venting System not Provided Fireplace Dimensions DVT38IN Locating Your Fireplace Clearance to CombustiblesMantels Hearth Framing and FinishingFinal Finishing Gas Line Installation Gas SpeciﬁcationsGas Inlet and Manifold Pressures High ElevationsControl System Installation Control SystemSpecial Feature for Cold Climates Inside view of wireless wall switchHand-Held Remote Control Transmitter Operating Instructions Key SettingsIntroduction LCD Liquid Crystal DisplayManual Function Thermostat FunctionContinuous Pilot Feature CP Childproof FeatureSetting LOCK-OUT CP Thermostatic Updating Feature Operational NotesGeneral Venting Location of Vent TerminationCanadian Installations1 US Installations2 General Venting Information Termination LocationQuick Reference for Fresh Air Restrictor Plate / Flue Bafﬂe ApplicationDVT38N DVT38P DVT44N DVT44P Canadian Installations USA InstallationsGeneral Information Assembling Vent Pipes SK8 Venting Pipes Horizontal TerminationSidewall Applications Use of the Restrictor Plates Horizontal Venting ApplicationsSidewall Installation StepAlways install horizontal venting on a level plane Vertical height requirementFresh Air Restrictor Plate Vertical Through-the-Roof Installation Typical offset applicationMin 610mm Chimney Components Component Description Model NumberGlass Frame Assembly Removal Glass CleaningRestrictor Plate Installation Glass InformationCeramic Refractory Installation Appliance Kit Model DescriptionLog, Lava Rock and Ember Placement DVT38IN LogsDVT44IN Logs Position the Log Grate Burner. Remove the twoPosition the Log Front Left. Pos- Figure Position the Log Rear LeftPosition the Log Front Middle Right DVT38IN logset complete Flame Characteristics Correct pilot ﬂame appearanceTrim Installation Lighting & Operating Instructions Lighting InstructionsTurning Off the Gas to the Appliance Troubleshooting American Flame Gas Control SystemIgniter operation Troubleshooting American Flame Gas Control System American Flame Gas Control System Error Codes What to CheckConversion Precautions Conversion ProcedureFuel Conversion Instructions Converting the Gas Control Valve Check Manifold PressureAir Shutter Settings Pilot Flame AdjustmentInjector Oriﬁce Size Matrix Valve Minimum Rate ScrewMaintenance Cleaning the Control SystemBurner and Burner Compartment DVT38IN, DVT44IN DVT38IN DVT44IN Colonial Red Limestone HerringboneFuel Conversion Kits Accessories Back-up Battery KitWall Mountable Wireless Remote Transmitter Ceramic Refractory KitsLimited Lifetime Warranty Product Covered by this WarrantyEfﬁciency Ratings Model EnerGuide Ratings Fireplace Efﬁciency %