Vermont Casting DVT38IN Installation & Operating Instructions, Certified To

Page 3

Chateau™

Installation & Operating Instructions

This gas fireplace must be installed by a qualified installer, preferably NFI or WETT (Canada) certified, in accordance with local building codes and with current CSA-B149.1 Installation codes for Gas Burning Appliances and Equipment. For USA Installations follow local codes and/or the current National Fuel Gas Code. ANSI Z223.1/NFPA 54.

FOR SAFE INSTALLATION AND OPERATION PLEASE NOTE THE FOLLOWING:

1 . This fireplace gives off high temperatures and should be located out of high traffic areas and away from furniture and draperies.

2.Children and adults should be alerted to the hazards of the high surface temperatures of this fireplace and should stay away to avoid burns or ignition of clothing.

3.CAUTION: Due to high glass surface temperature chil- dren should be carefully supervised when in the same room as fireplace.

�������

��������������

������������

������������������

�������������

��������������������

���������������

4.Under no circumstances should this fireplace be modified. Parts removed for servicing should be replaced prior to operating this fireplace again.

5.A professional service person should be contacted to inspect the fireplace annually. More frequent cleaning may be required due to excess lint and dust from carpeting, bedding material, etc.

6.Control compartments, burners and air passages in this fireplace should be kept clean and free of dust and lint. Make sure that the gas valve and pilot light are turned off before you attempt to clean this fireplace.

7.The venting system (chimney) of this fireplace should be checked at least once a year and if needed your venting system should be cleaned.

8.Keep the area around your fireplace clear of combustible materials, gasoline and other flammable vapor and liquids. This fireplace should not be used as a drying rack for cloth- ing, nor should Christmas stockings or decorations be hung on or around the fireplace.

9.Under no circumstances should any solid fuels (wood, coal, paper or cardboard etc.) be used in this fireplace.

10.The flow of combustion and ventilation air must not be obstructed in any way.

11.When the fireplace is installed directly on carpeting, vinyl tile or any combustible material other than wood, this fireplace must be installed on a metal or wood panel extending the full width and depth of the fireplace.

12.This fireplace requires adequate ventilation and combustion air to operate properly.

13.This fireplace must not be connected to a chimney flue serving a separate solid fuel burning fireplace.

14.When the fireplace is not in use it is recommended that the gas control valve be left in the “OFF” position.

15.For operation during power outages, the installation of the optional battery back-up kit Model DVTBBK is recommended at initial installation.

This appliance has been designed, certified and ap- proved to be installed indoors only.

DVT38IN / DVT44IN

Certified To

ANSI Z21.50b-2005/CSA 2.22b-2005

Vented Gas Fireplace

WARNING: Check with your electronics manufacturer before installing a television or other electronic de- vice above this fireplace.

This appliance may be installed in an aftermarket permanently located, manufactured home or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

The DVT38/44 has been approved for mobile home installations.

IMPORTANT:

PLEASE REVIEW THE FOLLOWING CAREFULLY

Remove any plastic from parts before turning the fire- place ON.

It is normal for fireplaces fabricated of steel to give off some expansion and/or contraction noises during the start up or cool down cycle. Similar noises are found with your furnace heat exchanger or car engine.

It is not unusual for your gas fireplace to give off some odor the first time it is burned. This is due to the curing of the paint and any undetected oil from the manufac- turing process.

Please ensure that your room is well ventilated- open all windows.

It is recommended that you burn your fireplace for at least ten (10) hours the first time you use it.

Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. California Health & Safety Code Sec. 25249.6

20011956

3

Image 3
Contents What to do if YOU Smell GAS INSTALLER/CONSUMER Safety InformationTable of Contents Installation & Operating Instructions Certified ToPlease Review the Following Carefully Requirements for the Commonwealth of Massachusetts Clear of ALL ObstructionsGas Equipment Venting System not Provided Fireplace Dimensions DVT38IN Locating Your Fireplace Clearance to CombustiblesMantels Hearth Framing and FinishingFinal Finishing High Elevations Gas Line InstallationGas Specifications Gas Inlet and Manifold PressuresControl System Control System InstallationInside view of wireless wall switch Special Feature for Cold ClimatesLCD Liquid Crystal Display Hand-Held Remote Control Transmitter Operating InstructionsKey Settings IntroductionThermostat Function Manual FunctionContinuous Pilot Feature CP Childproof FeatureSetting LOCK-OUT CP Operational Notes Thermostatic Updating FeatureLocation of Vent Termination General VentingGeneral Venting Information Termination Location Canadian Installations1 US Installations2Quick Reference for Fresh Air Restrictor Plate / Flue Baffle ApplicationDVT38N DVT38P DVT44N DVT44P Horizontal Termination Canadian InstallationsUSA Installations General Information Assembling Vent Pipes SK8 Venting PipesUse of the Restrictor Plates Horizontal Venting Applications Sidewall ApplicationsStep Sidewall InstallationVertical height requirement Always install horizontal venting on a level planeFresh Air Restrictor Plate Typical offset application Vertical Through-the-Roof InstallationMin 610mm Component Description Model Number Chimney ComponentsGlass Information Glass Frame Assembly RemovalGlass Cleaning Restrictor Plate InstallationAppliance Kit Model Description Ceramic Refractory InstallationDVT38IN Logs Log, Lava Rock and Ember PlacementPosition the Log Grate Burner. Remove the two DVT44IN LogsPosition the Log Rear Left Position the Log Front Left. Pos- FigurePosition the Log Front Middle Right DVT38IN logset complete Correct pilot flame appearance Flame CharacteristicsTrim Installation Lighting & Operating Instructions Lighting InstructionsTurning Off the Gas to the Appliance Troubleshooting American Flame Gas Control SystemIgniter operation Troubleshooting American Flame Gas Control System What to Check American Flame Gas Control System Error CodesConversion Precautions Conversion ProcedureFuel Conversion Instructions Check Manifold Pressure Converting the Gas Control ValveValve Minimum Rate Screw Air Shutter SettingsPilot Flame Adjustment Injector Orifice Size MatrixMaintenance Cleaning the Control SystemBurner and Burner Compartment DVT38IN, DVT44IN Colonial Red Limestone Herringbone DVT38IN DVT44INFuel Conversion Kits Ceramic Refractory Kits AccessoriesBack-up Battery Kit Wall Mountable Wireless Remote TransmitterProduct Covered by this Warranty Limited Lifetime WarrantyModel EnerGuide Ratings Fireplace Efficiency % Efficiency Ratings