Meco 6623S8E641 manual Clean the Burners. See How to Clean Burners in Care, Maintenance

Page 38

38

Troubleshooting

Problem

 

Possible Cause

 

Solution

Regulator coupling nut is not fully connected to LP cylinder

LP-Excess flow valve tripped in regulator

Vapor lock in connections

Tighten coupling nut by hand about one-half to three quar- ters additional turn. Do not use tools.

Turn Control Knobs to “Off” position and turn LP Gas Cyl- inder handle clockwise until it stops. Wait five minutes. Relight LP gas grill. If flame continues to be low, turn off gas at LP Gas Cylinder and grill. Disconnect the regulator from the LP Gas Cylinder. Reconnect the regulator to the LP Gas Cylinder. This will reset the excess flow valve Perform a leak test. Relight grill.

 

 

Obstructions in Burners

 

Clean the Burners. See “How to Clean Burners” in Care

 

 

 

 

and Maintenance.

 

 

Wet Electrodes and Burners

 

Dry Electrode with clean cloth. Air dry or use blow dryer.

 

 

Wire loose or disconnected

 

Reconnect the wire.

 

 

Wire shorting (sparking

 

Replace Igniter Wire/Electrode assembly.

 

 

between Igniter and Electrode)

 

(Call the Customer Service Department)

 

 

 

 

 

Burners will not light Burners not assembled correctly

 

See re-assembly after cleaning in Care and Maintenance.

using a match

 

 

 

 

LP Gas Cylinder is empty

 

Take LP Gas Cylinder to licensed LP gas supplier to be refilled.

 

 

 

 

Turn Control Knobs to “Off” position and turn LP Gas Cyl-

 

 

LP-Excess flow valve tripped in

 

inder handle clockwise until it stops. Wait five minutes. Relight

 

 

regulator

 

LP gas grill. If flame continues to be low, turn off gas at LP Gas

 

 

 

 

Cylinder and grill. Disconnect the regulator from the LP Gas

 

 

 

 

Cylinder. Reconnect the regulator to the LP Gas Cylinder. This

 

 

 

 

will reset the excess flow valve Perform a leak test. Relight grill.

Regulator Coupling nut is not fully connected to LP Gas Cylinder

Obstructions in Burners

Low flame or low heat LP-gas in LP Gas Cylinder is low

Excess flow valve tripped in regulator

Tighten Regulator Coupling nut by hand about one-half to three quarters additional turn. Do not use tools.

See “How to Clean Burners” in Care and Maintenance.

Check LP Gas Cylinder. Refill if necessary.

Turn Control Knobs to “Off” position and turn LP Gas Cyl- inder handle clockwise until it stops. Wait five minutes. Relight LP gas grill. If flame continues to be low, turn off gas at LP Gas Cylinder and grill. Disconnect the regulator from the LP Gas Cylinder. Reconnect the regulator to the LP Gas Cylinder. This will reset the excess flow valve Perform a leak test. Relight grill.

Flames blow out

High or gusting winds

Turn front of grill away from wind or increase flame height.

 

Gas in LP cylinder is low

Check LP Gas Cylinder. Refill if necessary.

 

Excess flow valve tripped

See “Low flame” problem above.

Image 38
Contents 6623S8E6416623S8Y641 For Outdoor Household Use Only. Not for Commercial UseTools Required for Assembly Carbon Monoxide HazardContents Preparation for AssemblyParts Illustration Model 6623S8E641 Description Quantity Parts List- Model 6623S8E641Key Description Quantity Parts Illustration Model 6623S8Y641 Parts List- Model 6623S8Y641 Step Rear Leg Frame Assembly Assembly InstructionsStep Front Leg Frame Assembly Step Rear Crossbrace Assembly Step Cart Frame Assembly Step Side Table Support AssemblyStep Side Tables to Cart Frame Assembly Step Heat Shield AssemblyStep Shroud Assembly Step Manifold Assembly Step Shroud to Cart AssemblyStep Cylinder Blocking Wires Assembly Step Wheel Assembly Model 6623S8Y641Wheel Assembly Model 6623S8E641 Step Drip Cup Wire Assembly Step Main Burner AssemblyStep Bowl and Cylinder Heat Shield Assembly Brace Wire AttachmentStep Side Burner Electrode Assembly Step Side Burner AssemblyStep Main Burner Electrode Assembly Electrode Wire Plug AssemblyStep Hood Handle Thermometer Assembly Model 6623S8Y641 onlyStep Hood/Hinge Assembly Step Flavor Activator / Warming Rack Assembly Step Cooking Grid / Control Knob AssemblyStep Battery in Igniter Installation Step Drip Cup AssemblyCylinder Retainer Wire Assembly LP Gas Cylinder Connecting/Disconnecting the GasUsing Gas Connecting LP Gas Cylinder LP Hose and RegulatorSelecting a Location Before Using Your LP Gas GrillInstallation Codes Performing a Leak TestHow to Perform a Leak Test First Time USE and as required Lighting the Grill Using the Pulse-Spark Ignitor Check The FlameManual Lighting of the Grill on Manually Lighting the Grill Manually Lighting the Side Burner Lighting the Side BurnerManually Lighting the Side Burner Cooking On the Gas Grill Grill Cooking Direct MethodIndirect Cooking Roasting Roasting Indirect MethodDirect Cooking on the Grids Warming Rack End of Cooking SessionCare and Maintenance Cleaning the GrillHow to Clean the Burners 16 gap Storage Troubleshooting EmergenciesSee How to Clean Burners in Care and Maintenance Clean the Burners. See How to Clean Burners in CareMaintenance Important Notice Limited Warranty Meco Corporation Limited Warranty