Emerson 8712E manual European Certifications N1 Atex Type n, Special Conditions for Safe Use

Page 28

Quick Installation Guide

Rosemount 8712 / 8700 Series

00825-0100-4664, Rev BB January 2013

Canadian Standards Association (CSA)

N0 Non-incendive for Class I, Division 2 Groups A, B, C, and D non-flammable fluids (T4 at 40 °C)

Dust-ignition proof Class II/III, Division 1 Groups E, F, and G

(T4 at 40 °C)

Hazardous Locations; Enclosure Type 4X

European Certifications

N1 ATEX Type n

Certificate No: Baseefa 05ATEX0170X

II 3G EEx nA nL IIC T4 (-40 °C ≤ Ta ≤ +60 °C) Vmax = 42 V DC

IP 66 0575

Special Conditions for Safe Use (x)

The apparatus is not capable of withstanding the 500V electrical strength test required by Clause 8.1of EN 60079-15: 2003. This must be taken into account when installing the apparatus.

International Certifications

IECEx

N7 IECEx Type n

Certificate No: IECEx BAS 07.0036X

Ex nA nL IIC T4 (Ta = -40 °C to + 60 °C)

Vmax = 42 V DC

Special Conditions for Safe Use (x)

The apparatus is not capable of withstanding the 500V electrical strength required by Clause 6.8.1of IEC 60079-15: 2005. This must be taken into account when installing the apparatus.

InMetro - Brazil

N2 Non-incendive, Type n

Certificate No: NCC 11.0198X

Ex nA ic IIC T4 Gc (-40 °C ≤ Ta ≤ +60 °C)

Vmax = 42 V DC

28

Image 28

Contents Quick Installation Guide Management Asia Pacific Private LimitedPRE-INSTALLATION Mechanical ConsiderationsDimensions are in inches millimeters 10912.02 305Installation Procedures Identify Options and ConfigurationsHardware Jumpers/Switches Environmental ConsiderationsHandling Electrical ConsiderationsMounting Upstream/Downstream PipingFlow Direction Sensor OrientationFlow Installation Flanged SensorsGaskets Flange BoltsCode Size ClassPound-feet Newton PTFE/ETFE liner PN10 SizeNewton Code Meter Polyurethane, Linatex, Adiprene and Neoprene Liners Size Alignment Wafer SensorsNominal Sensor Size Rosemount Alignment Spacer Table Line Size Dash No Alignment and Bolting Sanitary SensorsPound-feet Newton-meter Grounding Process Grounding Options Type of PipeLining StrapsGrounding with Grounding Electrode Wiring Power OutputsCoil Drive and Electrode Cables Power Outputs Conduit Ports and ConnectionsTransmitter to Sensor Wiring Remote Mount Cable Requirements and PreparationWiring the Transmitter to the Sensor Transmitter Terminal Sensor Terminal Wire Gauge Wire ColorDescription Part NumberRemote Mount Wiring Diagrams Connect the 4-20 mA Analog Signal Internal Power SourceExternal Power Source Cabling considerationsPowering the Transmitter Supply Wire RequirementsInstallation Category DisconnectsAC Ground or DC Ground Transmitter Power Cable 8712E Power SupplyFuse Basic Setup Basic Setup Local Operator InterfaceFunction Fast Keys Process Variables PV ReviewProduct Certifications Approved Manufacturing LocationsEuropean Directive Information International CertificatesEuropean Certifications N1 Atex Type n Special Conditions for Safe UseInternational Certifications N7 IECEx Type nSensor Approval Information Rosemount 8705 and 8711 Sensors Meter Size Inches Maximum Ambient TemperatureMaximum Process EC Declaration of Conformity Schedule