RedMax EDG2300R manual Maintenance Chart

Page 32

8. Maintenance

English

Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual.

■ MAINTENANCE CHART

			every	every	every
			25	50	100
system/compornent	procedure	before	hours	hours	hours	note
		use	after	after	after

fuel leaks, fuel spillage	wipe out	✔

fuel tank, air filter, fuel filter	inspect/clean	✔	✔			replace, if necessary

idle adjusting screw	see ■ADJUSTING	✔				replace carburetor
idle adjusting screw	IDLING SPEED (p.30)	✔				if necessary
	IDLING SPEED (p.30)					if necessary

spark plug	clean and readjust			✔		GAP: .025in(0.6~0.7mm)
spark plug	plug gap			✔		replace, if necessary
	plug gap					replace, if necessary

cylinder fins, intake air cooling vent	clean		✔

muffler, spark arrester, cylinder exhaust port	clean				✔

throttle lever, ignition switch	check operation	✔

gear case	grease			✔

screws/nuts/bolts	tighten/replace	✔			✔	not adjusting screws

32

Image 32

Contents EDG2300R Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido EDG2300R SpecificationsParts location Especificaciohes Emplacement des pieces Situación de las piezasFiche technique Symbols on the machine PositionEmission Control Important Engine InformationEmplacement PosiciónControl DE Emisiones Information Importante Concernant LE MoteurFor safe operation Consignes de securite Instrucciones de seguridad Work Gear and Clothing Consignes de securite Instrucciones de seguridad Equipement ET Vêtements DE TravailAvertissement Concernant Manipulation DE Carburant Equipo Y Prendas DE TrabajoThings to Check Before Using Your Portable GAS Drill Things to Check Before Starting UP the EngineVerifications a Effectuer Avant DE Demarrer LE Moteur Avoid Noise Problem Evitar Problemas DE Ruido Eviter LES Nuisances SonoresPortable GAS Drill Consignes de securite Instrucciones de seguridad Set up SE1 SE2 SE3Front grip Chuck unit Chuck handle Selection of a Suitable BitAssemblage Montaje Agarradera LevierLevier du mandrin Sélection d’un trépan approprié Palanquita del portabrocaRecommended Mixing Ratio Gasoline 50OIL When using Zenoah genuine oilFuel Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile Zenoah Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFor Your Engine LIFE, Avoid HOW to MIX FuelFueling the Unit Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Aceite Para USO EN Motores DE 4-TIEMPOS Operation Fonctionnement Uso How to operate Reverse control OP8 OP5 OP6 OP7 OP8Stopping Engine RUN Stop Boring Operation OP6, OP7Comment opérer la commande inverse Fonctionnement UsoMarche Levier Cómo operar el control de ReversiónAdjustment of Idling Speed Idle adjustment screwWhen Install or Loosen the Chuck More Securely OP10,11 OP9 OP10 OP11Vis de réglage du ralenti Clé de 19 mm Levier de verrouillageTornillo de ajuste de ralentí Llave fija de 19 mm Palanca de bloqueoMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoMA1 MA2 Daily InspectionInspection Every 25 Hours MA3Entretien Mantenimiento Cleaning the cylinder fins StorageLimpieza de las aletas del cilindro Rangement AlmacenamientoNettoyage des ailettes du cylindre Guide de localisation des pannes Troubleshooting guide10. Guía de localización y solución de problemas EDG2300R NotaParts list Gear Case a Engine Unit EDG2300R S/N 60000101 and up Qty Key# Part Number Description Limited Warranty RedMax Garantie limitée Garantía Limitada Page Komatsu Zenoah America INC