Desa (V)T32EN-A Series, (V)T32EP-A Series Installation for Vertical Termination, Horizontal H 1 +

Page 12

12

VENTING INSTALLATION INSTRUCTIONS Installation Planning (Cont.) Installation for Vertical Termination

VENTING INSTALLATION

INSTRUCTIONS

Continued

Venting with Two 90° Elbows

 

Horizontal (H1) +

Vertical (V)

Horizontal (H2)

5' min.

6' max.

6' min.

12' max.

7' min.

18' max.

8' min.

20' max.

20' max.

20' max.

45° Elbow

Figure 18 - Horizontal Termination Configuration for Venting Using Two 90° Elbows with Termination at 90° with Fireplace

INSTALLATION FOR VERTICAL TERMINATION

Note: Vertical restrictor must be installed in all vertical installations.

1.Determine the route your vertical venting will take. If ceiling joists, roof rafters or other framing will obstruct the venting system, consider an offset (see Figure 19) to avoid cutting load bearing members. Note: Pay special attention to these installation instructions for required clearances (air space) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafters, etc. Do not pack air spaces with insu- lation. Also note maximum vertical rise of the venting system and any maximum horizontal offset limitations.

2.Set the fireplace in desired location. Drop a plumb line down from the ceiling to the position of the fireplace exit flue. Mark the center point where the vent will penetrate the ceiling. Drill a small locating hole at this point.

Drop a plumb line from the inside of the roof to the locating hole in the ceiling. Mark the center point where the vent will penetrate the roof. Drill a small locating hole at this point.

Roof Flashing

Wall Strap

45° Elbow

Ceiling Firestop

Figure 19 - Offset with Wall Strap and 45° Elbows

www.desatech.com

116647-01A

Image 12
Contents For Your Safety For Your Safety What to do if YOU Smell GASSave this manual for future reference Table of Contents Safety InformationSafety Information Product Identification Local CodesProduct Features PRE-INSTALLATION PreparationLocation and Space Requirements Clearances Framing and FinishingLocation of Termination CAP Termination CAP AIR Supply Inlet GAS MeterVenting Installation Instructions Installation PrecautionsInstallation Planning Horizontal Termination InstallationAny wall. This will cause a fire hazard Vent Pipe ConnectionsConnecting Vent Cap with Horizontal Vent Pipe Venting Installation InstructionsHorizontal Termination Configurations Vertical Horizontal HVenting with Two 90 Elbows Horizontal H Vertical Min Max 12 max 18 max 20 max20 max Max Installation for Vertical Termination Horizontal H 1 +Vertical Horizontal H Min Max 12 max 18 max 20 max Flat Ceiling Installation Vertical Termination ConfigurationsVertical V Horizontal H1 + Horizontal H2 Min Max 20 max Venting with One 90 Elbow Vertical Horizontal H Min Max 20 maxVertical V Horizontal H Min Max 12 max 18 max 20 max Vertical VentingHigh Altitude Installation Desa 5/8 Pipe & Vent KitsNumber Description Fireplace Installation Check GAS Type Installing Optional Blower AccessoryFireplace Installation Model BKT InstallationBlower Wiring Diagram Installing GAS Piping to Fireplace Location Installation Items NeededConnecting Fireplace to GAS Supply Pressure Testing Gas Supply Piping SystemChecking GAS Connections Pressure Testing Fireplace Gas Connections Cleaning Glass DoorREMOVING/REPLACING Glass Door Removing Glass DoorInstalling Optional Brick Liner Model BL32D Installing LOGS, Lava Rock and Glowing EmbersInstalling Logs No and No Wiring Diagram Wall Switch InstallationOptional Remote Control For Your Safety Read Before LightingOperating Optional Blower Accessory LightingTo Turn OFF GAS To Appliance Optional RemoteCleaning Maintenance Pilot AssemblyInspecting Burners Glass DoorPilot and Burners LogsVenting System Troubleshooting Observed Problem Possible Cause RemedyGas leak. See Warning statement at TopReplacement Parts Specifications Service HintsTechnical Service Parts Under WarrantyIllustrated Parts Breakdown Illustrated Parts BreakdownParts List Parts ListBurner Assembly Models 109KEY Part Number Description QTY Accessories Owners Registration Form Postage Required 116647-01A Warranty Information Keep this Warranty