Desa (V)T32EN-A Series, (V)T32EP-A Series installation manual Wiring Diagram, Operating Fireplace

Page 23

23

FIREPLACE INSTALLATION

Continued

WALL SWITCH INSTALLATION

The installation of a wall switch allows you to activate the gas control valve and turn the fireplace on and off. The wall switch is to be connected to the incoming 120 volt regular household wiring that supplies the electricity to the fireplace.

OPTIONAL REMOTE CONTROL

INSTALLATION (Model WRC)

Note: If using optional wireless hand-held remote control, the wall switchmustbeintheONpositiontobeoperational.Theremotecontrol then becomes the switching mechanism for fireplace operation.

1.Open lower louver panel.

2.The WRC model receiver does not require a battery. The receiver can be installed by first plugging the short extension cord into the fireplace receptacle. Then plug the receiver unit into the extension cord. Finally plug the ignition module plug into the receiver unit (see Figure 46).

3.Activate the remote handset battery by removing the insulating tab on the back of the handset (see Figure 47). The battery is included pre-installed.

4.Once the battery is activated the unit is ready to use.

5.Close lower louver panel.

Fireplace

Receptacle

Remote Control

Receiver

Extension Cord

Ignition

Module Plug

 

Figure 46 - Installing the WRC Remote Receiver

Battery Cover

12 Volt Battery

Back of

HandsetPull to Remove

Insulation Tab

Figure 47 - Installing Battery into Back of Handset

WIRING DIAGRAM

 

 

 

 

PILOT

 

 

 

IGNITOR LEAD

 

 

 

 

ORANGE

 

 

 

 

 

 

SYNETEKCONTROLS IS1070B

BLUE

120VAC

 

E2

24VAC

 

E12

 

TRANSFORMER

 

 

 

 

WHITE

 

EV1

E8

 

 

 

 

 

 

 

 

E6

 

 

 

 

E4

 

 

 

 

E3

 

 

 

 

 

INC

BLACK

 

 

 

 

 

 

 

 

GROUND

 

EV2

 

 

RED

 

 

 

 

 

 

GREEN

 

 

 

OPERATING FIREPLACE

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A.This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electric switch.

Do not use any phone in your building.

Immediately call your gas supplier from a neighborʼs phone. Follow the gas supplierʼs instructions.

If you cannot reach your gas supplier, call the fire department.

C.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

116647-01A

www.desatech.com

Image 23
Contents Save this manual for future reference For Your SafetyFor Your Safety What to do if YOU Smell GAS Safety Information Table of ContentsLocal Codes Safety Information Product IdentificationLocation and Space Requirements Product FeaturesPRE-INSTALLATION Preparation Framing and Finishing ClearancesTermination CAP AIR Supply Inlet GAS Meter Location of Termination CAPHorizontal Termination Installation Venting Installation InstructionsInstallation Precautions Installation PlanningVent Pipe Connections Any wall. This will cause a fire hazardConnecting Vent Cap with Horizontal Vent Pipe Vertical Horizontal H Venting InstallationInstructions Horizontal Termination Configurations20 max Max Venting with Two 90 ElbowsHorizontal H Vertical Min Max 12 max 18 max 20 max Vertical Horizontal H Min Max 12 max 18 max 20 max Installation for Vertical TerminationHorizontal H 1 + Vertical V Horizontal H1 + Horizontal H2 Min Max 20 max Flat Ceiling InstallationVertical Termination Configurations Vertical Venting Venting with One 90 ElbowVertical Horizontal H Min Max 20 max Vertical V Horizontal H Min Max 12 max 18 max 20 maxNumber Description High Altitude InstallationDesa 5/8 Pipe & Vent Kits Installing Optional Blower Accessory Fireplace Installation Check GAS TypeBlower Wiring Diagram Fireplace InstallationModel BKT Installation Installation Items Needed Installing GAS Piping to Fireplace LocationChecking GAS Connections Connecting Fireplace to GAS SupplyPressure Testing Gas Supply Piping System Removing Glass Door Pressure Testing Fireplace Gas ConnectionsCleaning Glass Door REMOVING/REPLACING Glass DoorInstalling LOGS, Lava Rock and Glowing Embers Installing Optional Brick Liner Model BL32DInstalling Logs No and No For Your Safety Read Before Lighting Wiring DiagramWall Switch Installation Optional Remote ControlOptional Remote Operating Optional Blower AccessoryLighting To Turn OFF GAS To ApplianceGlass Door Cleaning MaintenancePilot Assembly Inspecting BurnersVenting System Pilot and BurnersLogs Observed Problem Possible Cause Remedy TroubleshootingTop Gas leak. See Warning statement atParts Under Warranty Replacement PartsSpecifications Service Hints Technical ServiceIllustrated Parts Breakdown Illustrated Parts BreakdownParts List Parts List109 Burner Assembly ModelsKEY Part Number Description QTY Accessories Owners Registration Form Postage Required 116647-01A Keep this Warranty Warranty Information