Desa (V) CD36T(N, (V) CD36R(N, P) Safety Information Product Identification, Local Codes

Page 3

SAFETY INFORMATION

PRODUCT IDENTIFICATION 3 LOCAL CODES

SAFETY INFORMATION

Continued

PRODUCT IDENTIFICATION

5.

This fireplace reaches high temperatures, Keep children and

 

adults away from hot surfaces to avoid burns or clothing igni-

 

tion. Fireplace will remain hot for a time after shutdown. Al-

 

low surfaces to cool before touching.

6.

Carefully supervise young children when they are in the room

 

with fireplace.

7.

Do not modify this fireplace under any circumstances. Any

 

parts removed for servicing must be replaced prior to operat-

 

ing fireplace.

8.

Turn fireplace off and let cool before servicing, installing, or

 

repairing. Only a qualified service person should install, ser-

 

vice or repair this fireplace. Have fireplace inspected annu-

 

ally by a qualified service person.

9.

You must keep control compartments, burners, and circulat-

 

ing air passages clean. More frequent cleaning may be needed

 

due to excessive lint and dust from carpeting, bedding mate-

 

rial, etc. Turn off the gas valve and pilot light before cleaning

 

fireplace.

10.

Have venting system inspected annually by a qualified service

 

person. If needed, have venting system cleaned or repaired.

 

See Cleaning and Maintenance, page##.

11.

Keep the area around your fireplace clear of combustible ma-

 

terials, gasoline, and other flammable vapor and liquids. Do

 

not run fireplace where these are used or stored. Do not place

 

items such as clothing or decorations on or around fireplace.

12.

Do not use this fireplace to cook food or burn paper or other

 

objects.

13.

Do not use any solid fuels (wood, coal, paper, cardboard, etc.)

 

in this fireplace. Use only the gas type indicated on the

 

nameplate.

14.

This appliance, when installed, must be electrically grounded

 

in accordance with local codes or, in the absence of local codes,

 

with the National Electric Code, ANSI/NFPA 70, or the Ca-

 

nadian Electric Code, CSA C22.1.

Upper

Louver

Panel

Glass

Door

Assembly

Lower

Louver

Panel

Junction Box

Rear Vent

Flue Collar

Top Vent

Flue Collar

Door Latch

Log

Set

Ember

Tray

Nailing

Flange

Control Valve

Piezo Ignitor with

Variable Input

Optional Remote and

Adjustment

Blower Control Mount

15.

Do not use fireplace if any part has been exposed to or under

 

water. Immediately call a qualified service person to arrange

 

for replacement of the unit.

16.

Do not operate fireplace if any log is broken or missing.

17.

Do not use a blower insert, heat exchanger insert, or other ac-

 

cessory not approved for use with this fireplace.

18.

Do not operate fireplace with glass door removed, cracked, or

 

broken.

19.

Provide adequate clearances around air openings.

NOTICE: This product is intended only as a supple- ment to your central heating system and is not to be installed as a primary source of heat. You may use this product for emergency heating during a power outage.

Figure 1 - Rear / Top Direct-Vent Fireplace

LOCAL CODES

Install and use fireplace with care. Follow all local codes. In the absence of local codes, use the current National Fuel Gas Code

ANSI Z223.1/NFPA 54* (USA) or the current CSA-B149.1 Instal- lation Code (Canada).

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarh Park

Quincy, MA 02269

116035-01B

www.desatech.com

Image 3
Contents Dedicated Rear and TOP Vent Fireplaces OWNER’S Operation Installation ManualFor Your Safety For Your Safety What to do if YOU Smell GASSafety Information Local Codes Safety Information Product IdentificationPRE-INSTALLATION Preparation Product FeaturesPRE-INSTALATION Preparation ClearancesFraming and Finishing Mantel Clearances Unit DimensionsMinimum Clearances for Termination Cap Location of Termination CAPInstallation Precautions Venting Installation InstructionsInstallation Planning Installing Siding Standoff With Vinyl Siding Horizontal Termination ConfigurationGround Floor Installation TOP Vent Venting with Three 90 Elbows Venting with Two 90 ElbowsFlat Ceiling Installation Vertical Termination Configurations Parts Lists for Venting Kits and Components Vertical VentingNumber Description Optional Blower Installation Model BK InstallationElectrical Supply Connection Model BKT Installation Wiring Diagram Decal Front of BlowerMillivolt Wiring Scheme Wiring DiagramsReceiver Volt Alkaline Battery Terminal Wires Battery Clip Installing Optional ControlsInstalling Optional Wall Mount Switch GWMS2 Installing Remote ReceiverCheck GAS Type High Altitude InstallationInstalling GAS Piping to Fireplace GAS Supply and PipingPropane/LP Connecting Fireplace to GAS SupplyInstallation Items Needed Natural FromEquipmentOpen Shutoff Valve Closed Checking GAS ConnectionsTest Pressures In Excess of 1/2 Psig 3.5 kPa Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPaHearth Access and Assembly Installing Logs and Glowing Embers For Your Safety Read Before LightingOperating Fireplace Optional HAND-HELD Remote Operation Manual Lighting ProcedureLighting Instructions To Turn OFF GAS To ApplianceOperating Fireplace Electronic Ignition System Optional Wireless Remote OperationThermostat Series Model Ghrctb ON/OFF Series Model GhrcbInspecting Burners Logs Cleaning and MaintenanceGlass Door Pilot and BurnersObserved Problem Possible Cause Remedy TroubleshootingInlet gas pressure is too low Gas leak. See Warning statement Ment Parts, Gas leak. See Warning statement at Specifications Replacement PartsService Hints Technical ServiceIllustrated Parts Breakdown KEY VCD36RN VCD36TN VCD36RP VCD36TP Description QTY Parts ListIllustrated Parts Breakdown KEY VCD36RN VCD36RP VCD36TN VCD36TP Description QTY 29 2 KEY VCD36RNE VCD36RPE VCD36TNE VCD36TPE Description QTY Accessories 116035-01B OWNER’S Registration Form Industrial Drive Box Bowling Green, KY Page Industrial Drive P.O. Box Model Serial No Date Purchased