Desa (V) CD36T(N, (V) CD36R(N GAS Supply and Piping, High Altitude Installation, Check GAS Type

Page 21

INSTALLING OPTIONAL CONTROLS

Continued

INSTALLING OPTIONAL WIRELESS REMOTE CONTROL - MODEL WRC (Electronic Ignition)

Installing and Activating the Remote Receiver

1.Open bottom louver and locate the plug receptacle. The plug receptacle is located either on the right or left side of cabinet.

2.The WRC model receiver does not require a battery. The re- ceiver can be installed by first plugging the short extension cord into the fireplace receptacle. Then plug the receiver unit into the extension cord. Finally plug the ignition module plug into the receiver unit (see Figure 45).

3.Activate the remote handset battery by removing the insulat- ing tab on the back of the handset (see Figure 46). The battery is included pre-installed.

4.Once the battery is activated the unit is ready to use.

INSTALLATING OPTIONAL CONTROLS (Cont.)

21

Installing Optional Wireless Remote Control - Model WRC

HIGH ALTITUDE INSTALLATION

GAS SUPPLY AND PIPING

Check Gas Type

Installing Gas Piping to Fireplace

When installing this fireplace in the USA at an elevation above 2000 feet (610 m), you may need to decrease the input rating by changing the existing burner orifice to a smaller size. Reduce input 4% for each 1000 feet (305 m) above sea level. Check with your local gas company for proper derate procedure and orifice size.

When installing this fireplace in Canada at an elevation above 4500 feet (1372 m), Check with local or provincial code authorities.

Consult your local gas company to help determine the proper orifice for your location.

For assistance with any high altitude installation contact DESA’s Customer Service Department at 1-866-672-6040.

GAS SUPPLY AND PIPING

5.Replace the bottom louver panel.

Fireplace

 

Receptacle

Remote Control

 

 

Receiver

CHECK GAS TYPE

Use proper gas type for the fireplace unit you are installing. If your gas supply is not correct, do not install fireplace. See retailer where you purchased the fireplace for proper fireplace according to your gas type or to purchase gas conversion kit (see Accessories, page 43).

INSTALLING GAS PIPING TO FIREPLACE

 

 

WARNING: A qualified service person must con-

 

Ignition

nect fireplace to gas supply. Follow all local codes.

Extension Cord

 

 

Module Plug

CAUTION: For propane/LP units, never connect

 

 

Figure 45 - Connecting WRC Remote Control Electronic

fireplace directly to the propane/LP supply. This

heater requires an external regulator (not supplied).

 

 

Install the external regulator between the fireplace

Battery Cover

 

and propane/LP supply.

 

 

 

 

12 Volt Battery

 

 

 

 

 

External

Propane/LP

 

 

Regulator

Supply Tank

Back of

Pull to Remove

 

 

Handset

Insulation Tab

 

 

Figure 46 - Installing Battery into Back of Handset

Vent

 

 

 

Pointing

 

HIGH ALTITUDE INSTALLATION

Down

 

 

 

Your DESA direct-vent fireplace has been tested and approved in

 

 

the USA for elevations from 0-2000 feet (610 m) and in Canada

Figure 47 - External Regulator with Vent Pointing Down (Pro-

at elevations from 0-4500 feet (1372 m).

pane/LP Only)

 

116035-01B

www.desatech.com

Page 20 Page 22
Image 21
Page 20 Page 22
Contents For Your Safety OWNER’S Operation Installation ManualFor Your Safety What to do if YOU Smell GAS Dedicated Rear and TOP Vent FireplacesSafety Information Local Codes Safety Information Product IdentificationPRE-INSTALLATION Preparation Product FeaturesPRE-INSTALATION Preparation ClearancesFraming and Finishing Mantel Clearances Unit DimensionsMinimum Clearances for Termination Cap Location of Termination CAPInstallation Precautions Venting Installation InstructionsInstallation Planning Installing Siding Standoff With Vinyl Siding Horizontal Termination ConfigurationGround Floor Installation TOP Vent Venting with Three 90 Elbows Venting with Two 90 ElbowsFlat Ceiling Installation Vertical Termination Configurations Parts Lists for Venting Kits and Components Vertical VentingNumber Description Optional Blower Installation Model BK InstallationElectrical Supply Connection Model BKT Installation Wiring Diagram Decal Front of BlowerMillivolt Wiring Scheme Wiring DiagramsInstalling Optional Wall Mount Switch GWMS2 Installing Optional ControlsInstalling Remote Receiver Receiver Volt Alkaline Battery Terminal Wires Battery ClipInstalling GAS Piping to Fireplace High Altitude InstallationGAS Supply and Piping Check GAS TypeInstallation Items Needed Connecting Fireplace to GAS SupplyNatural From Propane/LPTest Pressures In Excess of 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa EquipmentOpen Shutoff Valve ClosedHearth Access and Assembly Installing Logs and Glowing Embers For Your Safety Read Before LightingOperating Fireplace Lighting Instructions Manual Lighting ProcedureTo Turn OFF GAS To Appliance Optional HAND-HELD Remote OperationOperating Fireplace Electronic Ignition System Optional Wireless Remote OperationThermostat Series Model Ghrctb ON/OFF Series Model GhrcbInspecting Burners Glass Door Cleaning and MaintenancePilot and Burners LogsObserved Problem Possible Cause Remedy TroubleshootingInlet gas pressure is too low Gas leak. See Warning statement Ment Parts, Gas leak. See Warning statement at Service Hints Replacement PartsTechnical Service SpecificationsIllustrated Parts Breakdown KEY VCD36RN VCD36TN VCD36RP VCD36TP Description QTY Parts ListIllustrated Parts Breakdown KEY VCD36RN VCD36RP VCD36TN VCD36TP Description QTY 29 2 KEY VCD36RNE VCD36RPE VCD36TNE VCD36TPE Description QTY Accessories 116035-01B OWNER’S Registration Form Industrial Drive Box Bowling Green, KY Page Industrial Drive P.O. Box Model Serial No Date Purchased
Top Page Image Contents