Desa T32N-a SERIES Horizontal System Installation Using TWO 90 Elbows, Venting with Two 90 Elbows

Page 13

Venting Installation instructions

Continued

HORIZONTAL SYSTEM INSTALLATION USING TWO 90° ELBOWS

The following configurations show the minimum vertical rise requirements for a horizontal system using two 90° elbows.

Venting with Two 90° Elbows

		Horizontal (H1) +
Vertical (V)	Horizontal (H1)	Horizontal (H2)
5' min.	2' max.	6' max.
6' min.	4' max.	12' max.
7' min.	6' max.	18' max.
8' min.	8' max.	20' max.
20' max.	8' max.	20' max.

45° Elbow

Figure 17 - Horizontal Termination Configuration for Venting Using Two 90° Elbows

Venting with Two 90° Elbows
	Horizontal (H1) +
Vertical (V) Horizontal (H2)
5' min.	6' max.
6' min.	12' max.
7' min.	18' max.	45° Elbow
8' min.	20' max.	45° Elbow
8' min.	20' max.
20' max.	20' max.

Figure 18 - Horizontal Termination Configuration for Venting Using Two 90° Elbows

with Termination at 90° with Fireplace

116646-01D

www.desatech.com

Image 13

Contents CGDV32NR Natural GAS Tudor Models VT32N-A SeriesPROPANE/LP GAS Tudor Models VT32P-A Series CGDV32PRSafety Information Table of ContentsHigh traffic areas Product Identification Product FeaturesLocal Codes Location and space requirements Pre-Installation PreparationClearances Proper clearances must be maintainedFraming Clearances for Corner Installation Termination CAP AIR Supply Inlet GAS Meter Location of Termination CapInstallation Precautions Venting Installation InstructionsFemale Locking Lugs Male Slots Installation Planning Installing Siding Standoff Combustible Exterior Square Termination Venting InstallationVertical V Horizontal H Round Termination Kit HTK ShownCorner Installation Venting with Two 90 Elbows Horizontal System Installation Using TWO 90 ElbowsFlat Ceiling Installation Installation for vertical terminationConnect a section of pipe and extend up through the hole Venting with One 90 Elbow Vertical V Horizontal H Twist-lock the vent cap onto the last section of vent pipeParts list for venting kits and components High Altitude InstallationVertical Venting Desa 5/8 Pipe & Vent Kits Number DescriptionInstalling optional blower accessory Fireplace InstallationModel BK Installation Check GAS TypeModel BKT Installation Plug in blower power cordBlower Wiring Diagram Plug in blower power cord to duplex outletInstallation Items Needed Installing Gas Piping to Fireplace LocationChecking GAS Connections Connecting Fireplace to GAS SupplyWrong, fireplace may not run properly Pressure Testing Fireplace Gas Connections Installing optional wall Mount Switch gwmS2Test Pressures Equal To or Less Than Psig 3.5 kPa Removing/Replacing Glass Door Installing Remote ReceiverRemoving Louver Panels Replace screen/rod assembly by reversing step Installing Optional Brick liner Model BL32DCleaning Glass Door Removing Glass DoorClose top and bottom louvers Installing logs, lava rock and glowing embersOperating Fireplace For Your Safety Read Before LightingLighting Instructions Manual Lighting ProcedureTo Turn OFF GAS To Appliance Optional Hand-HeldOn/Off Series Thermostat SeriesPilot Assembly Operating optional blower accessoryInspecting Burners Operating optional GWMT1 Wall Mounted ThermostatBurner Flame Pattern Cleaning MaintenanceGlass Door Logs Pilot and burnersVenting system Observed Problem Possible Cause Remedy TroubleshootingBurner orifice clogged Clean burner see Cleaning Is lit Problem could be caused by Replace pilot assemblyDelayed ignition burner After pilot lights, keep gasImproper vent cap installa When burner is lit HI position when burner isCold Minute Air in gas line Operate burner until air is MixerStatement above Gas leak. See WarningService Hints Replacement PartsTechnical Service SpecificationsAccessories Illustrated Parts Breakdown Parts List Illustrated parts breakdown Burner Base Assembly 116646-01D 116646-01D Keep this Warranty Warranty InformationLimited Warranty DIRECT-VENT Fireplace