Desa VDCFTNB installation manual Installing Optional Blower Accessory GA3450TA

Page 13

INSTALLATION

Continued

4.Place mantel around fireplace on base (see Figure 12).

5.Assemble perimeter trim kit. See Assembling Perimeter Trim.

6.Firmly snap perimeter trim kit on shoulder screws. Shoulder screws are located on fire- place cabinet (see Figure 12).

7.Align perimeter trim kit for flush fit around opening.

8.Center mantel left to right on base making sure mantel is flush against wall.

9.Use two 3" wood screws provided and attach base of fireplace to wooden mantel base (see Figure 12).

10.Remove perimeter trim kit and mantel. Be careful not to damage wall or mantel.

11.Cut an access hole in base to run flexible gas line to fireplace (see Figure 12). Make sure to locate access hole so mantel will cover it when installed. Note: You can secure base to floor using wood screws. Countersink screw heads and putty over.

 

 

Hole for

 

 

3" Wood

 

 

Screw for

 

 

Attaching

Shoulder

 

Fireplace

Screw

 

to Mantel

 

 

 

 

Gas

 

 

Line

 

 

Access

 

 

Hole

Mantel

 

 

Base

 

 

Assembled

Hole for 3" Wood

Shoulder

Perimeter

Screws

 

Screw for Attaching

Trim

Fireplace to

 

 

 

Wooden Base

Figure 12 - Attaching Perimeter Trim to

Fireplace

12.Install gas line. See Connecting To Gas Sup- ply, page 16.

13.Check for leaks. See Checking Gas Connec- tions, page 17.

14.Place mantel around fireplace. Be careful not to damage wall or mantel.

15.Place perimeter trim kit on the shoulder screws located on the side and top of the fireplace. Firmly snap trim over shoulder screws on fireplace (see Figure 12).

16.Adjust assembly to remove any gaps. Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the mantel. The openings are located at top behind the area for top louver (see Figure 12).

17.Reinstall top louver.

Assembling Perimeter Trim (Perimeter trim shipped with mantel)

1.Remove packaging from three remaining pieces of trim.

2.Locate two adjusting plates with set screws and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 13.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top trim (see Figure 13).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side perimeter trim (see Figure 13).

6.While firmly holding edges of perimeter trim together, tighten both set screws on the adjust- ing plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other corner.

8.Set perimeter trim assembly aside for later installation.

Set

Screws

 

Adjusting

 

 

Plate

 

 

 

Slot

Top Trim

Shim

 

Mitered Edge

 

 

Side Trim

 

 

Figure 13 - Assembling Perimeter Trim

INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TA

Removing Upper Louver To install the blower accessory, you must first remove the upper louver.

1.Lift screen off fireplace and remove log set if installed.

116526-01A

www.desatech.com

13

Image 13
Contents What to do if YOU Smell GAS Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Safety Information Product Identification Product FeaturesLocal Codes UnpackingSheet Metal Screws Hood Louver Firebox Top Hood AssemblyTools Required Phillips screwdriver Shoulder Screw ScreenProviding Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationFireplace Clearances Installation ItemsMinimum Clearance to Combustible Materials TopActual Framing Height BUILT-IN Fireplace InstallationFront Width DepthMantel Shelf Optional Mantel InstallationSide of Firebox Top Louver Bottom LouverInstalling Optional Blower Accessory GA3450TA Switch Power Cord Installing Blower AccessoryPlate Remote Wire Blower Harness Bracket Lower Louver Door SwitchExtension Cord For Built-In InstallationBlower Bracket Connecting to GAS Supply Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlChecking GAS Connections Equipment Shutoff Valve Propane/LP Supply Tank Pressure Testing Fireplace Gas ConnectionsEquipment Open Shutoff Valve Closed Gas Regulator or Gas Control Valve EquipmentInstalling Receiver Optional Wireless HAND-HELD Remote Control AccessoriesReceiver Volt Terminal Battery Wires Battery Clip Installing 9-Volt Battery in Hand-Held Remote Control UnitFeed wires through rectangular slots Control Valve To Wall Thermostat or Switch Or SwitchInstall the base onto the wall with the pro- vided screws Remove jumper wire from control valve see ,For Your Safety Read Before Lighting Installing LOG SET and ScreenOperating Fireplace Lighting InstructionsTo Turn OFF GAS To Appliance Manual Lighting ProcedureThermostat Control Operation Shutting Off FireplaceAUTO/OFF/ON Switch REMOTE-READY Models For Your Safety Read Before LightingOperating Blower Pilot Ignitor Burner Electrode Piezo Flame Control Ignitor Adjustment Knob ButtonPilot Burner Ignitor Electrode Optional HAND-HELD Remote Operation Manual ModeThermostat Series Model HRC200 ON/OFF Series Model HRC100Optional GWMT1 Wall Mounted Thermostat Optional GWMS2 Wall Mounted SwitchInspecting Burners Cleaning MaintenanceCabinet LOG SETAir Passageways ExteriorObserved Problem Possible Cause Remedy TroubleshootingBurner orifice is clogged Burner orifice is clogged Clean burner see CleaningMote-Ready Models Only Models OnlyMote-Ready Models Only Power is low When heated, vapors fromSlight smoke or odor during Nance,Gas leak. See Warning Thermostat Models SpecificationsRemote-Ready Models Firebox Models VDC Illustrated Parts BreakdownParts List Thermostat Models Vdcftpb and Vdcftnb Thermostat Models REMOTE-READY Models Vdcfrnb and Vdcfrpb KEY Part Numbers Vdcfrpb Vdcfrnb Description QTY Equipment Shutoff Valve GA5010 AccessoriesPerimeter Trim KIT GA6095 THERMOSTAT-CONTROLLED Blower KIT GA3450TInformation Video Receiver and HAND-HELD Remote Control KIT HRC100 SeriesFor all models. Creates the sound of a real burn- ing fire Service Hints Replacement PartsTechnical Service Parts Under Warranty116526-01A Keep this Warranty Warranty InformationLimited Warranty VENT-FREE Compact Classic Hearth