Desa VDCFTNB Optional Wireless HAND-HELD Remote Control Accessories, Installing Receiver

Page 19

INSTALLATION

Continued

OPTIONAL WIRELESS HAND-HELD

REMOTE CONTROL ACCESSORIES

Remote-Ready Models Only

(HRC100 Series & HRC200 Series)

Installing Receiver

1.Disconnect wires from the control valve (see Figure 26) .

2.Locate the battery clip mounted on the back of the receiver (see Figure 27).

3.Slide 9-volt battery (not included) through the clip.

4.Attach the terminal wires to the battery (see Figure 27).

5.Connect wires from remote receiver to control valve as shown in Figure 28.

6.Install remote receiver unit onto remote/ blower bracket using screws provided (see Figure 28).

Figure 26 - Disconnecting Wires From

Control Valve

Receiver

9-Volt

Terminal

Battery

Wires

 

Battery Clip

Figure 27 - Attaching Battery to Receiver

White Wire to

TH Terminal on

Control Valve

Remote

Receiver

Red Wire to

TPTH Terminal on

Control Valve

Figure 28 - Installing Remote Receiver

Installing 9-Volt Battery in Hand-Held Remote Control Unit

1.Remove battery cover on back of remote control unit.

2.Attach terminal wires to the battery (not in- cluded). Place battery into the battery housing.

3.Replace battery cover onto remote control unit.

Battery

Remote Control Unit

Cover

Terminal

Wires

Battery

Housing

9-Volt Battery

Figure 29 - Installing Battery in Hand- Held Remote Control Unit

OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1 (Remote-Ready Models Only)

WARNING: Read and fol- low installation instructions. Installation should be done by a qualified installer familiar with low-voltage wiring procedures.

WARNING: Do not connect this thermostat to any electrical source! Electrical shock and/or fire hazard will occur.

1.Remove jumper wire from control valve (see Figure 26).

2.Connect one terminal of 25 ft. wire to the “TH” terminal on the control valve. Connect the other terminal to the “THTP” terminal on the control valve. See Figure 30, page 20.

3.Route the 25 ft. wire to a convenient location to mount your thermostat (no outside wall). IMPORTANT: The wire may be shortened but must not be lengthened.

The thermostat should be mounted 54" above the floor in a location where there is good air circulation. Avoid heat sources such as lamps, direct sunlight, fireplace or heat and

air conditioning ducts.

116526-01A

www.desatech.com

19

Image 19
Contents What to do if YOU Smell GAS Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Safety Information Unpacking Product FeaturesProduct Identification Local CodesShoulder Screw Screen Hood AssemblySheet Metal Screws Hood Louver Firebox Top Tools Required Phillips screwdriverProviding Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationTop Installation ItemsFireplace Clearances Minimum Clearance to Combustible MaterialsDepth BUILT-IN Fireplace InstallationActual Framing Height Front WidthTop Louver Bottom Louver Optional Mantel InstallationMantel Shelf Side of FireboxInstalling Optional Blower Accessory GA3450TA Switch Installing Blower AccessorySwitch Power Cord Plate Remote Wire Blower Harness Bracket Lower Louver DoorExtension Cord For Built-In InstallationBlower Bracket Connecting to GAS Supply Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlChecking GAS Connections Gas Regulator or Gas Control Valve Equipment Pressure Testing Fireplace Gas ConnectionsEquipment Shutoff Valve Propane/LP Supply Tank Equipment Open Shutoff Valve ClosedInstalling 9-Volt Battery in Hand-Held Remote Control Unit Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Receiver Volt Terminal Battery Wires Battery ClipRemove jumper wire from control valve see , Control Valve To Wall Thermostat or Switch Or SwitchFeed wires through rectangular slots Install the base onto the wall with the pro- vided screwsLighting Instructions Installing LOG SET and ScreenFor Your Safety Read Before Lighting Operating FireplaceShutting Off Fireplace Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat Control OperationAUTO/OFF/ON Switch REMOTE-READY Models For Your Safety Read Before LightingOperating Blower Pilot Ignitor Burner Electrode Piezo Flame Control Ignitor Adjustment Knob ButtonPilot Burner Ignitor Electrode ON/OFF Series Model HRC100 Manual ModeOptional HAND-HELD Remote Operation Thermostat Series Model HRC200Optional GWMT1 Wall Mounted Thermostat Optional GWMS2 Wall Mounted SwitchInspecting Burners Cleaning MaintenanceExterior LOG SETCabinet Air PassagewaysObserved Problem Possible Cause Remedy TroubleshootingModels Only Burner orifice is clogged Clean burner see CleaningBurner orifice is clogged Mote-Ready Models OnlyNance, When heated, vapors fromMote-Ready Models Only Power is low Slight smoke or odor duringGas leak. See Warning Thermostat Models SpecificationsRemote-Ready Models Firebox Models VDC Illustrated Parts BreakdownParts List Thermostat Models Vdcftpb and Vdcftnb Thermostat Models REMOTE-READY Models Vdcfrnb and Vdcfrpb KEY Part Numbers Vdcfrpb Vdcfrnb Description QTY THERMOSTAT-CONTROLLED Blower KIT GA3450T AccessoriesEquipment Shutoff Valve GA5010 Perimeter Trim KIT GA6095Information Video Receiver and HAND-HELD Remote Control KIT HRC100 SeriesFor all models. Creates the sound of a real burn- ing fire Parts Under Warranty Replacement PartsService Hints Technical Service116526-01A Keep this Warranty Warranty InformationLimited Warranty VENT-FREE Compact Classic Hearth