Desa VDCFTNB Open lower louver door by swinging door down see, Installing Blower Accessory

Page 14

INSTALLATION

Continued

2.Remove 4 screws from upper louver (see Figure 11, page 12). Save these screws.

3.Pull upper louver straight out from the cabinet. Be careful not to scratch the paint. Set louver aside.

4.Open lower louver door by swinging door down (see Figure 11, page 12).

Installing Blower Accessory

CAUTION: Label all wires prior to disconnection when ser- vicingcontrols.Wiringerrorscan cause improper and dangerous operation.

CAUTION: Verify proper op- eration after servicing.

Note: If you are using a mantel with your fireplace, use the following instructions. If your fireplace is built-in, see For Built-In Installation, page 15.

1.Install snap bushings found in blower kit into hole in left side of outer casing and into one of the holes in rear of remote/blower bracket.

2.Make sure the wire harness is firmly connected to the terminals on the blower bracket assembly.

3.Note the wire locations on back of AUTO/ OFF/ON switch. The terminals on back of switch are numbered 1, 2 and 3. Carefully remove red wire from terminal 3 and blue wire from terminal 1. Black wire can remain on middle terminal 2 (see Figure 14).

Blower

Wiring Routing

Bracket

Wire Hole in Baffle

Blower

Assembly

Harness

Mounting

Screw

 

 

Holes

4.Carefully disconnect green and white wires at their insulated connectors (see Figure 15).

5.In top of the fireplace cabinet, locate the four mounting holes on the outer casing. Align these four holes with those on the blower bracket assembly. Attach blower bracket as- sembly to the outer casing with 4 #10 screws provided (see Figure 14).

6.Route the wire harness through the hole in left side of baffle and between firebox wrapper and outer casing.

7.Insert the 4 wire harnesses from behind the remote/blower bracket through hole in rear of bracket with bushing and through the left rectan- gular hole to front of fireplace (see Figure 14).

8.Reconnect red wire to switch position 3. Reconnect blue wire to switch position 1. Reconnect green and white wires.

9.Install the switch plate on the remote/blower bracket with 2 #10 screws provided (see Figure 16). Route power cord out of the cabinet by insert- ing it through the bushing on the outer casing (see Figure 14). Plug fan kit into 120-Volt grounded power supply and test operation. Note: When switch is in the AUTO position, the fan will start after the fireplace has run for a few moments. The fan will continue to run for several moments after the fireplace has been turned off. When switch is in the ON position, the fan will run until turned to OFF.

10.Reinstall upper louver beginning with bottom screws (see Figure 11, page 12). Close lower louver door.

Fan Switch (Auto/Off/On)

1Auto

 

Off

2

 

 

 

3

Blue

Thermostat

 

 

 

 

 

 

 

On

 

Switch

 

 

 

(N.O.)

 

 

 

 

Blue

110/115

 

Red

 

Blower

V.A.C.

 

 

 

Black

 

 

Motor

 

 

 

Red

 

 

 

 

 

White

 

 

White

 

Green

 

 

Green

Switch

Power

 

Cord

3

 

2

 

1

 

Switch

 

Plate

Remote/

Wire

Blower

Harness Bracket

Lower Louver Door

Figure 15 - Wiring Diagram For Blower

Accessory Standard Installation

Remote/

Blower

Bracket

Switch

Plate

Screw

Figure 14 - Installing Blower Bracket Assembly (Remote-Ready Unit Shown)

Figure 16 - Installing Switch Plate to

Remote/Blower Bracket

14

www.desatech.com

116526-01A

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory What to do if YOU Smell GASTable of Contents Safety Information Safety Information Local Codes Product FeaturesProduct Identification UnpackingTools Required Phillips screwdriver Hood AssemblySheet Metal Screws Hood Louver Firebox Top Shoulder Screw ScreenDetermining FRESH-AIR Flow for Fireplace Location AIR for Combustion VentilationProviding Adequate Ventilation Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Installation Check GAS TypeMinimum Clearance to Combustible Materials Installation ItemsFireplace Clearances TopFront Width BUILT-IN Fireplace InstallationActual Framing Height DepthSide of Firebox Optional Mantel InstallationMantel Shelf Top Louver Bottom LouverInstalling Optional Blower Accessory GA3450TA Plate Remote Wire Blower Harness Bracket Lower Louver Door Installing Blower AccessorySwitch Power Cord SwitchBlower Bracket For Built-In InstallationExtension Cord Connecting to GAS Supply Checking GAS Connections Connecting Equipment Shutoff Valve to Heater ControlInstallation Items Needed Equipment Open Shutoff Valve Closed Pressure Testing Fireplace Gas ConnectionsEquipment Shutoff Valve Propane/LP Supply Tank Gas Regulator or Gas Control Valve EquipmentReceiver Volt Terminal Battery Wires Battery Clip Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Installing 9-Volt Battery in Hand-Held Remote Control UnitInstall the base onto the wall with the pro- vided screws Control Valve To Wall Thermostat or Switch Or SwitchFeed wires through rectangular slots Remove jumper wire from control valve see ,Operating Fireplace Installing LOG SET and ScreenFor Your Safety Read Before Lighting Lighting InstructionsThermostat Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off FireplaceOperating Blower REMOTE-READY Models For Your Safety Read Before LightingAUTO/OFF/ON Switch Pilot Burner Ignitor Electrode Piezo Flame Control Ignitor Adjustment Knob ButtonPilot Ignitor Burner Electrode Thermostat Series Model HRC200 Manual ModeOptional HAND-HELD Remote Operation ON/OFF Series Model HRC100Optional GWMS2 Wall Mounted Switch Optional GWMT1 Wall Mounted ThermostatCleaning Maintenance Inspecting BurnersAir Passageways LOG SETCabinet ExteriorTroubleshooting Observed Problem Possible Cause RemedyMote-Ready Models Only Burner orifice is clogged Clean burner see CleaningBurner orifice is clogged Models OnlySlight smoke or odor during When heated, vapors fromMote-Ready Models Only Power is low Nance,Gas leak. See Warning Remote-Ready Models SpecificationsThermostat Models Illustrated Parts Breakdown Firebox Models VDCParts List Thermostat Models Vdcftpb and Vdcftnb Thermostat Models REMOTE-READY Models Vdcfrnb and Vdcfrpb KEY Part Numbers Vdcfrpb Vdcfrnb Description QTY Perimeter Trim KIT GA6095 AccessoriesEquipment Shutoff Valve GA5010 THERMOSTAT-CONTROLLED Blower KIT GA3450TFor all models. Creates the sound of a real burn- ing fire Receiver and HAND-HELD Remote Control KIT HRC100 SeriesInformation Video Technical Service Replacement PartsService Hints Parts Under Warranty116526-01A Limited Warranty VENT-FREE Compact Classic Hearth Warranty InformationKeep this Warranty
Top Page Image Contents