Desa VDCFTNB installation manual For Built-In Installation, Extension Cord, Blower Bracket

Page 15

INSTALLATION

Continued

For Built-In Installation

WARNING: A licensed elec- trician must connect the wiring harness to electrical supply following all local codes. Electri- cian must provide a clamp on the box cover to secure the wiring. Wiring should be routed through the bushing in the hole on the outer casing of ﬁreplace.

1.Install snap bushing from blower kit into one hole on rear of remote/blower bracket (see Figure 17). The other hole is for a strain relief clamp (not supplied) to secure incoming electrical supply.

2.Follow steps 2 through 6 in Installing Blower Accessory, page 14.

3.A licensed electrician must follow the wiring diagram to connect incoming electrical supply to fan kit wiring harness (see Figure 18).

4.Plug power cord to outlet receptacle (not provided) as shown in Figure 17. Wind the extra power cord and tie with plastic wire strap (see Figure 17). Set power cord bundle between the remote/blower bracket and outer casing, away from the burner.

5.Test to make sure blower is working properly.

6.Reinstall upper louver beginning with bottom screws (see Figure 11, page 12) and close lower louver.

Extension Cord
Use extension cord if needed. The cord must have
a three-prong, grounding plug and a three-hole re-
ceptacle. Make sure cord is in good shape. It must
be heavy enough to carry the current needed. An
undersized cord will cause a drop in line voltage.
This will result in loss of power and overheating. Use
a No. 16 AWG cord for lengths less than 50 feet.
	Fan Switch
	(Auto/Off/On)
		1 Auto
	Off	2
		3			Blue		Thermostat
			On					Switch
			On					(N.O.)
110/115			Red						Blue
V.A.C.			Red						Blower
	Black									Motor
	Black							Red
								Red
	White							White
	Green							Green

Figure 18 - Wiring Diagram For Blower

Accessory Built-In Installation

Blower Bracket	Wire Harness
Blower Bracket
Assembly
Screw

Power Cord

Switch

Outlet Receptacle (not included)

3 2 1

Switch

Plate

Plastic Wire Strap	Wire Harness

Clamp Connector (not included)

Remote/ Blower Bracket

Lower Louver Door

Figure 17 - Installing Blower Bracket Assembly

116526-01A

www.desatech.com

15

Image 15

Contents What to do if YOU Smell GAS Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Safety Information Unpacking Product FeaturesProduct Identification Local CodesShoulder Screw Screen Hood AssemblySheet Metal Screws Hood Louver Firebox Top Tools Required Phillips screwdriverAIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationTop Installation ItemsFireplace Clearances Minimum Clearance to Combustible MaterialsDepth BUILT-IN Fireplace InstallationActual Framing Height Front WidthTop Louver Bottom Louver Optional Mantel InstallationMantel Shelf Side of FireboxInstalling Optional Blower Accessory GA3450TA Switch Installing Blower AccessorySwitch Power Cord Plate Remote Wire Blower Harness Bracket Lower Louver DoorFor Built-In Installation Extension CordBlower Bracket Connecting to GAS Supply Connecting Equipment Shutoff Valve to Heater Control Installation Items NeededChecking GAS Connections Gas Regulator or Gas Control Valve Equipment Pressure Testing Fireplace Gas ConnectionsEquipment Shutoff Valve Propane/LP Supply Tank Equipment Open Shutoff Valve ClosedInstalling 9-Volt Battery in Hand-Held Remote Control Unit Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Receiver Volt Terminal Battery Wires Battery ClipRemove jumper wire from control valve see , Control Valve To Wall Thermostat or Switch Or SwitchFeed wires through rectangular slots Install the base onto the wall with the pro- vided screwsLighting Instructions Installing LOG SET and ScreenFor Your Safety Read Before Lighting Operating FireplaceShutting Off Fireplace Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat Control OperationREMOTE-READY Models For Your Safety Read Before Lighting AUTO/OFF/ON SwitchOperating Blower Piezo Flame Control Ignitor Adjustment Knob Button Pilot Ignitor Burner ElectrodePilot Burner Ignitor Electrode ON/OFF Series Model HRC100 Manual ModeOptional HAND-HELD Remote Operation Thermostat Series Model HRC200Optional GWMT1 Wall Mounted Thermostat Optional GWMS2 Wall Mounted SwitchInspecting Burners Cleaning MaintenanceExterior LOG SETCabinet Air PassagewaysObserved Problem Possible Cause Remedy TroubleshootingModels Only Burner oriﬁce is clogged Clean burner see CleaningBurner oriﬁce is clogged Mote-Ready Models OnlyNance, When heated, vapors fromMote-Ready Models Only Power is low Slight smoke or odor duringGas leak. See Warning Specifications Thermostat ModelsRemote-Ready Models Firebox Models VDC Illustrated Parts BreakdownParts List Thermostat Models Vdcftpb and Vdcftnb Thermostat Models REMOTE-READY Models Vdcfrnb and Vdcfrpb KEY Part Numbers Vdcfrpb Vdcfrnb Description QTY THERMOSTAT-CONTROLLED Blower KIT GA3450T AccessoriesEquipment Shutoff Valve GA5010 Perimeter Trim KIT GA6095Receiver and HAND-HELD Remote Control KIT HRC100 Series Information VideoFor all models. Creates the sound of a real burn- ing ﬁre Parts Under Warranty Replacement PartsService Hints Technical Service116526-01A Warranty Information Keep this WarrantyLimited Warranty VENT-FREE Compact Classic Hearth