Desa VDCFTNB installation manual Inspecting Burners, Cleaning Maintenance

Page 27

INSPECTING BURNERS

Check pilot flame pattern and burner flame pat- terns often.

PILOT FLAME PATTERN

Figure 45 shows a correct pilot flame pattern. Figure 46 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the ther- mocouple. This will cause the thermocouple to cool. When the thermocouple cools, the fireplace will shut down.

If pilot flame pattern is incorrect, as shown in Figure 46

•turn fireplace off (see To Turn Off Gas to Appli- ance, page 22 for Thermostat-Controlled Mod- els or page 24 for Remote-Ready Models)

•see Troubleshooting, page 29

Note: The pilot flame on natural gas units will have a slight curve, but flame should be blue and have no yellow or orange color.

Pilot Burner

Figure 47 - Correct Burner Flame Pattern

Figure 48 - Incorrect Burner Flame Pattern

CLEANING AND

MAINTENANCE

WARNING: Turn off fireplace and let cool before cleaning.

Thermocouple

Figure 45 - Correct Pilot Flame Pattern (Propane/LP Remote-Ready Shown)

Pilot Burner

Thermocouple

Figure 46 - Incorrect Pilot Flame Pattern

(Propane/LP Remote-Ready Shown)

BURNER FLAME PATTERN

Figure 47 shows a correct burner flame pattern. Figure 48 shows an incorrect burner flame pattern. The incorrect burner flame pattern shows sporadic, irregular flame tipping. The flame should not be dark or have an orange/reddish tinge.

Note: When using the fireplace the first time, the flame will be orange for approximately one hour until the log cures.

If burner flame pattern is incorrect, as shown in Figure 48

•turn fireplace off (see To Turn Off Gas to Appli- ance, page 22 for Thermostat-Controlled Mod- els or page 24 for Remote-Ready Models)

•see Troubleshooting, page 29

CAUTION: You must keep

control areas, burner and cir-

culating

air passageways of

fireplace

clean. Inspect these

areas of fireplace before each

use. Have fireplace inspected

yearly by a qualified service

person. Fireplace may need

more frequent cleaning due to

excessive lint from carpeting,

pet hair, bedding material, etc.

WARNING: Failure to keep

the primary air opening(s) of

the burner(s) clean may result in

sooting and property damage.

BURNER INJECTOR HOLDER AND

PILOT AIR INLET HOLE

The primary air inlet holes allow the proper

amount of air to mix with the gas. This provides

a clean burning flame. Keep these holes clear of

dust, dirt, lint and pet hair. Clean these air inlet

holes prior to each heating season. Blocked air

holes will create soot. We recommend that you

clean the unit every three months during operation

and have fireplace inspected yearly by a qualified

service person.

 

116526-01A

www.desatech.com

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents What to do if YOU Smell GAS Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Safety Information Unpacking Product FeaturesProduct Identification Local CodesShoulder Screw Screen Hood AssemblySheet Metal Screws Hood Louver Firebox Top Tools Required Phillips screwdriverAIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationTop Installation ItemsFireplace Clearances Minimum Clearance to Combustible MaterialsDepth BUILT-IN Fireplace InstallationActual Framing Height Front WidthTop Louver Bottom Louver Optional Mantel InstallationMantel Shelf Side of FireboxInstalling Optional Blower Accessory GA3450TA Switch Installing Blower AccessorySwitch Power Cord Plate Remote Wire Blower Harness Bracket Lower Louver DoorFor Built-In Installation Extension CordBlower Bracket Connecting to GAS Supply Connecting Equipment Shutoff Valve to Heater Control Installation Items NeededChecking GAS Connections Gas Regulator or Gas Control Valve Equipment Pressure Testing Fireplace Gas ConnectionsEquipment Shutoff Valve Propane/LP Supply Tank Equipment Open Shutoff Valve ClosedInstalling 9-Volt Battery in Hand-Held Remote Control Unit Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Receiver Volt Terminal Battery Wires Battery ClipRemove jumper wire from control valve see , Control Valve To Wall Thermostat or Switch Or SwitchFeed wires through rectangular slots Install the base onto the wall with the pro- vided screwsLighting Instructions Installing LOG SET and ScreenFor Your Safety Read Before Lighting Operating FireplaceShutting Off Fireplace Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat Control OperationREMOTE-READY Models For Your Safety Read Before Lighting AUTO/OFF/ON SwitchOperating Blower Piezo Flame Control Ignitor Adjustment Knob Button Pilot Ignitor Burner ElectrodePilot Burner Ignitor Electrode ON/OFF Series Model HRC100 Manual ModeOptional HAND-HELD Remote Operation Thermostat Series Model HRC200Optional GWMT1 Wall Mounted Thermostat Optional GWMS2 Wall Mounted SwitchInspecting Burners Cleaning MaintenanceExterior LOG SETCabinet Air PassagewaysObserved Problem Possible Cause Remedy TroubleshootingModels Only Burner orifice is clogged Clean burner see CleaningBurner orifice is clogged Mote-Ready Models OnlyNance, When heated, vapors fromMote-Ready Models Only Power is low Slight smoke or odor duringGas leak. See Warning Specifications Thermostat ModelsRemote-Ready Models Firebox Models VDC Illustrated Parts BreakdownParts List Thermostat Models Vdcftpb and Vdcftnb Thermostat Models REMOTE-READY Models Vdcfrnb and Vdcfrpb KEY Part Numbers Vdcfrpb Vdcfrnb Description QTY THERMOSTAT-CONTROLLED Blower KIT GA3450T AccessoriesEquipment Shutoff Valve GA5010 Perimeter Trim KIT GA6095Receiver and HAND-HELD Remote Control KIT HRC100 Series Information VideoFor all models. Creates the sound of a real burn- ing fire Parts Under Warranty Replacement PartsService Hints Technical Service116526-01A Warranty Information Keep this WarrantyLimited Warranty VENT-FREE Compact Classic Hearth
Top Page Image Contents