Desa VDCFTNB installation manual Installation, Check GAS Type

Page 9

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your pri- mary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualified ser- vice person must install fire- place. Follow all local codes.

WARNING: Never install the fireplace

in a bedroom or bathroom

in a recreational vehicle

where curtains, furniture, clothing or other flammable objects are less than 36 inches from the front, top or sides of the fireplace

as a fireplace insert

in high traffic areas

in windy or drafty areas

WARNING: Never install in a bedroom or bathroom.Any heat- ing product with a Btu/Hr rating over 10,000 cannot be used in a bedroom.

CAUTION: This fireplace cre- ates warm air currents. These currents move heat to wall sur- faces next to fireplace. Installing fireplace next to vinyl or cloth wall coverings or operating fireplace where impurities (such as, but not limited to, tobacco smoke, aromatic candles, clean- ing fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.

IMPORTANT: Vent-free fireplaces add moisture to the air. Although this is beneficial, installing fire- place in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, page 6.

Note: Your fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against any exterior surface on the rear, sides or top of your fireplace, except where standoff spacers are integrally attached. If standoff spacers are attached to your fireplace, these spacers can be placed directly against wall or framing materials.

Note: When installing fireplace directly on carpet- ing, tile or other combustible material, other than wood flooring, the fireplace shall be installed on a metal or wood panel extending the full width and depth of the fireplace.

Use the dimensions shown for rough openings to create the easiest installation (see Built-In Fire- place Installation, page 11).

CHECK GAS TYPE

Use the correct gas type (natural or propane/LP) for your unit. If your gas supply is not correct, do not install fireplace. Call dealer where you bought fireplace for proper type fireplace.

WARNING: This appliance is equipped for (natural or pro- pane/LP) gas. Field conversion is not permitted.

116526-01A

www.desatech.com

9

Image 9
Contents What to do if YOU Smell GAS Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Safety Information Product Identification Product FeaturesLocal Codes UnpackingSheet Metal Screws Hood Louver Firebox Top Hood AssemblyTools Required Phillips screwdriver Shoulder Screw ScreenAIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationFireplace Clearances Installation ItemsMinimum Clearance to Combustible Materials TopActual Framing Height BUILT-IN Fireplace InstallationFront Width DepthMantel Shelf Optional Mantel InstallationSide of Firebox Top Louver Bottom LouverInstalling Optional Blower Accessory GA3450TA Switch Power Cord Installing Blower AccessoryPlate Remote Wire Blower Harness Bracket Lower Louver Door SwitchFor Built-In Installation Extension CordBlower Bracket Connecting to GAS Supply Connecting Equipment Shutoff Valve to Heater Control Installation Items NeededChecking GAS Connections Equipment Shutoff Valve Propane/LP Supply Tank Pressure Testing Fireplace Gas ConnectionsEquipment Open Shutoff Valve Closed Gas Regulator or Gas Control Valve EquipmentInstalling Receiver Optional Wireless HAND-HELD Remote Control AccessoriesReceiver Volt Terminal Battery Wires Battery Clip Installing 9-Volt Battery in Hand-Held Remote Control UnitFeed wires through rectangular slots Control Valve To Wall Thermostat or Switch Or SwitchInstall the base onto the wall with the pro- vided screws Remove jumper wire from control valve see ,For Your Safety Read Before Lighting Installing LOG SET and ScreenOperating Fireplace Lighting InstructionsTo Turn OFF GAS To Appliance Manual Lighting ProcedureThermostat Control Operation Shutting Off FireplaceREMOTE-READY Models For Your Safety Read Before Lighting AUTO/OFF/ON SwitchOperating Blower Piezo Flame Control Ignitor Adjustment Knob Button Pilot Ignitor Burner ElectrodePilot Burner Ignitor Electrode Optional HAND-HELD Remote Operation Manual ModeThermostat Series Model HRC200 ON/OFF Series Model HRC100Optional GWMT1 Wall Mounted Thermostat Optional GWMS2 Wall Mounted SwitchInspecting Burners Cleaning MaintenanceCabinet LOG SETAir Passageways ExteriorObserved Problem Possible Cause Remedy TroubleshootingBurner orifice is clogged Burner orifice is clogged Clean burner see CleaningMote-Ready Models Only Models OnlyMote-Ready Models Only Power is low When heated, vapors fromSlight smoke or odor during Nance,Gas leak. See Warning Specifications Thermostat ModelsRemote-Ready Models Firebox Models VDC Illustrated Parts BreakdownParts List Thermostat Models Vdcftpb and Vdcftnb Thermostat Models REMOTE-READY Models Vdcfrnb and Vdcfrpb KEY Part Numbers Vdcfrpb Vdcfrnb Description QTY Equipment Shutoff Valve GA5010 AccessoriesPerimeter Trim KIT GA6095 THERMOSTAT-CONTROLLED Blower KIT GA3450TReceiver and HAND-HELD Remote Control KIT HRC100 Series Information VideoFor all models. Creates the sound of a real burn- ing fire Service Hints Replacement PartsTechnical Service Parts Under Warranty116526-01A Warranty Information Keep this WarrantyLimited Warranty VENT-FREE Compact Classic Hearth