Desa RFP28TB installation manual Pilot

Page 24

24

OPERATING HEATER

Continued

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information at the top of page 23. If you don’t smell gas, go to the next step.

5.Turn control knob counterclockwise C-clockwiseto the PILOT position. Press in control knob for five (5) seconds (see Figure 28, page 23).

Note: You may be running this heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds. This will allow air to bleed from the gas system.

6.With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the front of burner. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, refer to Troubleshooting, pages 28 through

31.Also contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure, page 25.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs.

Ignitor Electrode

Thermocouple

Pilot Burner

Figure 29 - Pilot

Note: If pilot goes out, repeat steps 3 through 7. This heater has a safety interlock system. Wait one (1) minute before lighting pilot again.

8.Turn control knob counterclockwise C-clockwiseto desired heating level. The main burner should light. Set control knob to any heat level between HI

and LO.

CAUTION

WARNING ICON

G 001

Do not try to adjust heating levels by using the manual shutoff valve.

101935

Image 24
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASContents Safety InformationSafety Information Safety Device Product IdentificationPiezo Ignition System Thermostatic Heat ControlAssembly Installing LogRemoving Front Panel Of Heater Attaching Brass Front Trim to Front Panel Assembling HeaterAssembly Assembling and Attaching Brass TrimAIR for VentilationProviding Adequate Ventilation AIR for Combustion and Ventilation Determining AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingAppliances in both spaces Ventilation AIR Ventilation Air From OutdoorsInstallation Installation ItemsCheck GAS Type Locating HeaterThermostat Sensing Bulb Locating Thermostat Sensing BulbAttaching Thermostat Sensing Bulb Installation Options Mounting BracketMethods For Attaching Mounting Bracket To Wall Marking Screw LocationsAttaching Mounting Bracket to Wall Placing Heater On Mounting BracketSecuring Hearth Base to Floor Mounting Heater on Optional Hearth BaseMounting Heater to Optional Hearth Base Attaching Heater to Hearth BaseInstalling Mantel to Heater Assembling MantelPre-Drilled Hole Screw Hearth Base Accessory Wood Plug Connecting to GAS Supply External Regulator with Vent Pointing DownConnecting To GASSupply Checking GASPressure Testing Heater GAS Connections CheckingFor Your Safety Read Before Lighting Operating HeaterPilot Shutting Off Heater Shutting Off Burner Only pilot stays litInspecting Burner Pilot Flame PatternBurner Flame Pattern Correct Burner Flame PatternTrouble Shooting ODS/PILOT and BurnerCabinet Cleaning and Mainte TroubleTROUBLE- Shooting If you smell gas Shut off gas supplyDo not try to light any appliance Ing statement atService Replacement PartsTechnical HintsParts Centrals FBDAccessories FAN KIT GA3100A Manual or GA3200TA ThermostatHearth Base GHB802B or GHB38 GS601 Black SurroundUnfinished GMU801A,B Finished GMF800A,B Unfinished GMC23UA Finished GMC22FAUnfinished GMC33U Finished GMC32F RFP28TB Parts List RFP28TB KEY Part Number Description101935 101935 Warranty Information Keep this Warranty