Desa RFP28TB Mounting Heater to Optional Hearth Base, Attaching Heater to Hearth Base

Page 17

INSTALLATION

If securing to a concrete floor, drill a 1 3/8" deep hole using a 1/4" diameter con-

 

Continued

crete drill bit. Completely insert anchors into each hole.

3. Mount heater to hearth base following steps under Mounting Heater to Optional

 

Hearth Base, page 17. After mounting heater, position heater and hearth base

 

over drilled holes. With slotted screwdriver, secure hearth base to floor with

 

four wood screws.

Mounting Heater to Optional Hearth Base

1.Lay heater on its back on a table with the bottom of heater overhanging the edge of the table.

2.Remove 2 shipping screws in bottom of heater. Discard shipping screws.

3.Line up mounting holes on top of hearth base with holes in bottom of heater (see Figure 18).

4.Using a Phillips screwdriver, secure hearth base to heater with four sheet metal screws (see Figure 18).

Base

Bottom of Heater

Shipping

Screw

 

Mounting Holes

Holes for Securing

Sheet Metal

Heater to Floor

 

Screw

Figure 18 - Attaching Heater to Hearth Base

5.Stand heater up on base.

6.Attach laminated insert onto hearth insert if desired (see Figure 19). Place hearth insert in hearth base as shown in Figure 19 below.

7.Assemble brass trim (see steps 1 through 7 under Assembling and Attaching Brass Trim, page 7).

8.Slide base trim on heater base. Attach brass trim to base with two brass screws included as shown in Figure 19 below.

Laminate

Sheet

Hearth Insert

Adhesive

Strips

 

Screw

 

Brass Base

 

Trim

 

Continued

Figure 19 - Placing Hearth Insert on Heater Base

and Attaching Brass Base Trim

17

101935

Image 17
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information ContentsSafety Information Product Identification Safety DevicePiezo Ignition System Thermostatic Heat ControlRemoving Front Panel Of Heater AssemblyInstalling Log Assembling Heater Attaching Brass Front Trim to Front PanelAssembling and Attaching Brass Trim AssemblyProviding Adequate Ventilation AIR forVentilation Determining if You Have a Confined or Unconfined Space AIR for Combustion and VentilationDetermining AIR Flow for Heater Location Appliances in both spaces Ventilation AIRVentilation Air From Inside Building Ventilation Air From Outdoors Ventilation AIRInstallation Items InstallationCheck GAS Type Locating HeaterAttaching Thermostat Sensing Bulb Thermostat Sensing BulbLocating Thermostat Sensing Bulb Mounting Bracket Installation OptionsMethods For Attaching Mounting Bracket To Wall Marking Screw LocationsPlacing Heater On Mounting Bracket Attaching Mounting Bracket to WallMounting Heater on Optional Hearth Base Securing Hearth Base to FloorAttaching Heater to Hearth Base Mounting Heater to Optional Hearth BaseAssembling Mantel Installing Mantel to HeaterPre-Drilled Hole Screw Hearth Base Accessory Wood Plug External Regulator with Vent Pointing Down Connecting to GAS SupplyTo GAS ConnectingSupply Checking GASChecking Pressure Testing Heater GAS ConnectionsOperating Heater For Your Safety Read Before LightingPilot Shutting Off Burner Only pilot stays lit Shutting Off HeaterPilot Flame Pattern Inspecting BurnerCorrect Burner Flame Pattern Burner Flame PatternCabinet Trouble ShootingODS/PILOT and Burner Trouble Cleaning and MainteTROUBLE- Shooting Shut off gas supply If you smell gasDo not try to light any appliance Ing statement atReplacement Parts ServiceTechnical HintsFBD Parts CentralsFAN KIT GA3100A Manual or GA3200TA Thermostat AccessoriesHearth Base GHB802B or GHB38 GS601 Black SurroundUnfinished GMC33U Finished GMC32F Unfinished GMU801A,B Finished GMF800A,BUnfinished GMC23UA Finished GMC22FA RFP28TB KEY Part Number Description Parts List RFP28TB101935 101935 Keep this Warranty Warranty Information