Desa RFP28TB Securing Hearth Base to Floor, Mounting Heater on Optional Hearth Base

Page 16

INSTALLATION

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel

Continued of heater (see Figure 17).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching To Wall Anchor Method, page 15.

If installing bottom mounting screw into wall stud, drill holes at marked loca- tions using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten. Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 21-23).

Figure 17 - Installing Bottom Mounting Screws

B. MOUNTING HEATER ON OPTIONAL HEARTH BASE

WARNING

If installing the GHB802 or GHB802A base on heater, and using with a GA series heater blower accessory along with a GS601 surround or a GM800 or GM900 series mantel, the surround or mantel clearance to back wall should be 3/4 inch. This space is not necessary if using a GHB38 or GHB802B hearth base. This will improve flame appearance and combus- tion. Use only a GHB802B or GHB38 hearth base if using a GA series heater blower accessory with a GM700 series, GMC32F or GMC33U corner mantel.

Tools needed: #2 Phillips screwdriver, slotted screwdriver, and electric drill (if

 

securing base to floor)

 

The optional hearth base kit includes the following:

 

Hearth Base

4

Wood Screws

4 Sheet Metal Screws

Brass Base Trim

Hearth Insert

4

Anchors

Laminate Sheet & adhesive

2 Brass Screws

Note: It is an option to secure “A” model hearth base to floor. You must secure the “B” or GHB38 model hearth base to floor. To secure hearth base to floor, follow instructions under Securing Hearth Base to Floor, below. If not securing hearth base to floor, proceed to Mounting Heater to Optional Hearth Base, page 17.

Securing Hearth Base to Floor

1.Position hearth base in desired location. Mark holes for drilling (See Figure 18, page 17). Remove hearth base.

2.For carpeted floor, make a small cut with a sharp knife at marked locations before drilling.

If securing to a wood floor, drill a 3/4" deep hole using a 1/8" diameter drill bit. Do not use anchors in wood floors.

16

101935

Image 16
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASContents Safety InformationSafety Information Safety Device Product IdentificationPiezo Ignition System Thermostatic Heat ControlInstalling Log AssemblyRemoving Front Panel Of Heater Attaching Brass Front Trim to Front Panel Assembling HeaterAssembly Assembling and Attaching Brass TrimVentilation AIR forProviding Adequate Ventilation Determining AIR Flow for Heater Location AIR for Combustion and VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRAppliances in both spaces Ventilation AIR Ventilation Air From OutdoorsInstallation Installation ItemsCheck GAS Type Locating HeaterLocating Thermostat Sensing Bulb Thermostat Sensing BulbAttaching Thermostat Sensing Bulb Installation Options Mounting BracketMethods For Attaching Mounting Bracket To Wall Marking Screw LocationsAttaching Mounting Bracket to Wall Placing Heater On Mounting BracketSecuring Hearth Base to Floor Mounting Heater on Optional Hearth BaseMounting Heater to Optional Hearth Base Attaching Heater to Hearth BaseInstalling Mantel to Heater Assembling MantelPre-Drilled Hole Screw Hearth Base Accessory Wood Plug Connecting to GAS Supply External Regulator with Vent Pointing DownConnecting To GASSupply Checking GASPressure Testing Heater GAS Connections CheckingFor Your Safety Read Before Lighting Operating HeaterPilot Shutting Off Heater Shutting Off Burner Only pilot stays litInspecting Burner Pilot Flame PatternBurner Flame Pattern Correct Burner Flame PatternODS/PILOT and Burner Trouble ShootingCabinet Cleaning and Mainte TroubleTROUBLE- Shooting If you smell gas Shut off gas supplyDo not try to light any appliance Ing statement atService Replacement PartsTechnical HintsParts Centrals FBDAccessories FAN KIT GA3100A Manual or GA3200TA ThermostatHearth Base GHB802B or GHB38 GS601 Black SurroundUnfinished GMC23UA Finished GMC22FA Unfinished GMU801A,B Finished GMF800A,BUnfinished GMC33U Finished GMC32F RFP28TB Parts List RFP28TB KEY Part Number Description101935 101935 Warranty Information Keep this Warranty