Omega Engineering OS530HR, OS531, OS53X-CF, OS533, OS532, OS530L, OS523, OS534 Field of View OS524

Page 21

2Using the Handheld Infrared Thermometer

		DISTANCE: SENSOR TO OBJECT (FT)
(IN)	0'	16'	50'	82'
(IN)
DIA.*
SPOT	0.5"@ 0			8.7"
SPOT
			5.1"
	0.9"	1.5"	5.1"
	0.9"	1.5"
			D:S = 110:1
		38	130	221
			130	221
(MM)		13mm @ 0
*
DIA.	*SPOT DIAMETER MEASURED
DIA.		AT 90% ENERGY
SPOT		AT 90% ENERGY
SPOT	0	5	15	25
		DISTANCE: SENSOR TO OBJECT (M)

Figure 2-10 Field of View OS524

3.The target temperature and emissivity are displayed on the LCD.

Determine the emissivity of the target (refer to Appendix B). Press the

key to increment the target emissivity. Press the key to decrement the target emissivity.

4.Press the key to lock the trigger. The icon will appear on the display. This allows the thermometer to operate continuously

whether or not the trigger is pulled. To unlock the trigger, press the

key again. The icon is no longer displayed. When the trigger is pulled, the Laser Sighting as well as the display backlight

will stay on .

5.After completing a temperature measurement, release the trigger. In order to conserve battery life, the thermometer goes into sleep mode and the Laser Sighting turns off.

2-6

Image 21

Contents User’s Guide Servicing North America For immediate technical or application assistanceServicing Europe Unpacking Instructions Model No Description Page Unpacking Instructions Chapter General Description Contents General Description Introduction Features OS531 OS532 OS533 OS534 OS530HR OS530L-CF Features OS523 OS524 Front of the Thermometer Parts of the ThermometerDisplay Details Key OS530 Series Handheld Infrared Thermometer Rear View Rear of the ThermometerGeneral Description Ac Power Operation Battery OperationOS530/OS520 Series with Built-in Laser Sighting Operating the ThermometerField of View OS531, OS532, OS530L Field of View OS534, OS523-1 Field of View OS523-2 10 Field of View OS524 Trigger Measurement Techniques11 Recorder Hookup If the trigger is pulled two times in rapid sequence Real Time Mode Active OperationRecall Mode 13. Visual Function Flow Chart Using the Lock Function Adjusting EmissivityCalculating Temperature Values Changing the Temperature from F to C or vice versaTurning on the Display Backlighting Thermocouple Input OS532, OS533, OS534 If you are not in High Alarm Display Mode HAL when Using the Alarm FunctionsTo set the low alarm value OS533, OS534, OS523, OS524 To disable this mode, press the key again Icon disappears One Stop Bit Key to decrement the printing interval. System Requirements Irtempsoft Connecting the IR-System to the PC Using the Handheld Infrared Thermometer Storing the Temperature Data on Command OS534, OS523, OS524 Erasing the Temperature Data from Memory Mode Recall Mode Passive OperationFunctional Flow Chart Recall Mode Reviewing the Last Parameters AMB temperature MEM locationPRN F Using the Handheld Infrared Thermometer Laser Sighting Rear View DescriptionLaser Dot Operating the Laser SightingLines of Sight of the Laser Sighting and Thermometer Sighting Scope Installing and Operating the Sighting ScopeInstalling the Sighting Scope Maintenance Replacing the Batteries Safety WarningCleaning the Lens Calibrating the ThermometerServicing the Laser Sighting Problem Solution Troubleshooting GuideProblem If you see an error code, either Target are offset by design Specifications Specifications are for all models except where notedOS533, OS534, OS523, OS524 No Laser Sighting 17 hours continuous Laser Sighting Glossary of Key Strokes Glossary of Key Strokes Appendix How Infrared Thermometry Works a Thermal RadiationBlackbody Calculating Temperature Optics Field of View Appendix Emissivity Values MetalsMaterial Emissivity ε NonmetalsAppendix Determining an Unknown Emissivity Figure C-1. Determining Emissivity Figure C-2. Determining Emissivity with a Drilled Hole Appendix Determining an Unknown Emissivity Index Field of View Diagrams Recall WARRANTY/DISCLAIMER PH/CONDUCTIVITY Shop online at omega.com