Invacare TerminatorTM SS manual Section Back, Replacing Top End Back Upholstery

Page 20

BACK

SECTION 3	BACK

Replacing Top End Back Upholstery.

1.Unlatch the two (2) fastening flaps that secure the top of the back upholstery to the back canes.

2.Remove the fastening flaps from the back canes by lifting straight up.

3.Remove the seat cushion.

4.Separate the bottom of the back upholstery from either the underside or top of the seat upholstery (depending on back style).

5.Install the NEW fastening flaps onto the back canes.

NOTE: The fastening flap with logo is for the left back cane.

NOTE: Right and left is determined by sitting in the wheelchair.

6.Securely latch the bottom of the back upholstery to the fasteners on either the underside or top of the seat upholstery (depending on back style).

7.Adjust the NEW back upholstery to the desired tautness. Refer to ADJUSTING TOP END BACK UPHOLSTERY in this section of the manual.

Fastening Flap	Back Upholstery
Fastening Flap	Fastening
	Flap with
	Logo
	Seat
	Upholstery

Bottom of Back

Upholstery

Wheelchair

Frame

FIGURE 3 - ADJUSTING/REPLACING BACK UPHOLSTERY -

TOP END BACK UPHOLSTERY

Terminator™ SS

20

Part No. 1052712 Rev D

Image 20

Contents Terminator SS Wheelchair TIE-DOWN Restraints and Seat Positioning Straps Special NotesSpecial Notes Table of Contents Limited Warranty Specifications SpecificationsStability Operating InformationGeneral Guidelines Section General GuidelinesDo not operate on roads, streets or highways General Guidelines SectionDo not tip the wheelchair without assistance Tire Pressure and Information Weight TrainingWeight Limitation Coping with Everyday Obstacles SAFETY/HANDLING of WheelchairsStability and Balance Shortening Lengthening Percentage of Weight DistributionUnoccupied Occupied REACHING, Leaning Backwards TippingREACHING, Leaning Bending Forward Tipping Curbs StairwaysTransferring to and from Other Seats ESCALATORS? SorrySection Safety Inspection Safety Inspection ChecklistSafety Inspection Troubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance ProceduresSafety Inspection Back Section BackSection Back Back Angle to Seat Rail Adjusting Top End Back Upholstery TOP END Back Upholstery FigureSection Back Replacing Top End Back UpholsteryReplacing Adjustable Tension Back Upholstery Custom Manual Adjustable Tension Back Upholstery FigureAdjustable Tension Straps Fastening Strap Hole Back NumberSeat Section SeatSeat Section Replacing Custom Manual Screw on Seat UpholsterySection Wheels REMOVING/INSTALLING Rear Wheels FigureWheels Adjusting QUICK-RELEASE Axles Figure Wheels SectionAND/OR OUT Installing QUAD-RELEASE Axles FigureAdjusting QUAD-RELEASE Handles Figure Handrim Replacement Figure Removing Play from Rear WheelsCamber Clamps REPAIRING/REPLACING Rear WHEEL, TIRE/TUBEOPENING/CLOSING Clamps Figure Receiver Tube Clamps Camber Clamps Quick Release Lever Standard Closed PositionOpen Receiver Tube ClampsA4 Camber System Figure Adjusting Rear Wheel CamberCamber Tube Determining TOE IN/TOE OUT Figures 8 Determining TOE TOE OUT Measuring Centerlines of Rear WheelsAdjusting TOE IN/TOE OUT Course Adjustment FigureCamber Tube 2000 Figure A4 Camber SystemAdjusting TOE IN/TOE OUT A4 Camber System Course Adjustment Fine Adjustment Figure Adjusting TOE IN/TOE OUT A4 Camber System Fine AdjustmentAdjusting Center of Gravity Never Operate Wheelchair with BothEnds of the Indexing Tape ShowingTube Adjusting Wheelbase WidthWheelbase Width Camber Replacing Axle Tube Figure Front WheelchairRear CamberAdjusting the Axle Tube Axle Tube Camber Tube TOE IN/TOE OUT Measurement is Within ±1/8-INCH TOE IN/TOE OUT Measurement is not Within ±1/8-INCHSuspension Caster REPLACING/ADJUSTING Casters FigureNON-SUSPENSION Caster Adjusting Front Caster Height Figure Adjusting Front Caster HeightWheel Lock ADJUSTMENT/REPLACEMENT Figure Adjusting the High/Low Mount Wheel LockWheel Lock Adjustment Replacing the High/Low Mount Wheel LockADJUSTING/REPLACING Standard Footrest Figure If Replacing or Adjusting the FootrestIf Replacing the Footrest Footrest / ANTI-TIPPERINSTALLING/ADJUSTING Optional A4 Footrest Figure InstallingAdjusting Footplate Angle AdjustmentFootplate Depth Adjustment DepthAdjustment ANTI-TIPPER REPLACEMENT/ADJUSTMENT FigureReplacement Elastomers and Suspension Replacing Rear Elastomers FigureSuspension Section SuspensionSuspension Section Replacing Rear ElastomersReplacing Front Elastomers Figure Detail CREMOVING/INSTALLING/REPLACING Suspension Tubes Figure Installing Suspension TubesRemoving Suspension Tubes Detail B Suspension Tube HardwareAdjusting SEAT-TO-FLOOR Height Figure Adjusting SEAT-TO Floor HeightRepositioning the Axle Tube Figure Clamp Position Must be INVERTED- Proceed to StepProcedure Suspension Detail C Axle Tube PositionsSuspension Procedure Repositioning Quick Release Levers FigureReverse Side View of Camber Clamp with Quick Release LeverTerminator SS Warranty WarrantyCanada