Invacare TerminatorTM SS manual TOP END Back Upholstery Figure, Adjusting Top End Back Upholstery

Page 19

BACK

SECTION 3

 

 

FOLDING/UNFOLDING THE BACK (FIGURE 2)

NOTE: This procedure is for folding back chairs only.

WARNING

Back MUST be locked securely in place before using the chair.

1.Lift up on the back and pull towards the rear of the chair until it locks into place.

2.To fold the back, pull up on the black nylon cord and push the back forward

Back Cane

Seat Frame

FIGURE 2 - FOLDING/UNFOLDING THE BACK

ADJUSTING/REPLACING BACK UPHOLSTERY

TOP END BACK UPHOLSTERY (FIGURE 3)

WARNING

The back flaps and center upholstery MUST be replaced if hook and loop fastener is worn or DOES NOT secure the flaps to the back center upholstery. If hook and loop fastener is NOT secure, serious injury may result.

Adjusting Top End Back Upholstery.

1.Unlatch the two (2) fastening flaps that secure the top of the back upholstery to the back canes.

2.Align the top of the back upholstery with the fastening flaps ensuring the top of the back upholstery is even with the top of the back canes.

3.Adjust to the desired tautness.

TIGHTER back upholstery will increase the stability and maintain normal maneuverability of the wheelchair because the user is pushed forward in the wheelchair slightly.

LOOSER back upholstery will increase the maneuverability and make the wheelchair more unstable because additional weight is being distributed onto the rear wheels.

4.Securely latch back upholstery to the fastening flaps.

BACK

Part No. 1052712 Rev D

19

Terminator™ SS

Image 19
Contents Terminator SS Special Notes Special NotesWheelchair TIE-DOWN Restraints and Seat Positioning Straps Table of Contents Limited Warranty Specifications SpecificationsSection General Guidelines StabilityOperating Information General GuidelinesDo not tip the wheelchair without assistance General Guidelines SectionDo not operate on roads, streets or highways Weight Limitation Weight TrainingTire Pressure and Information Stability and Balance SAFETY/HANDLING of WheelchairsCoping with Everyday Obstacles Unoccupied Occupied Percentage of Weight DistributionShortening Lengthening REACHING, Leaning Bending Forward TippingREACHING, Leaning Backwards Stairways Tipping CurbsESCALATORS? Sorry Transferring to and from Other SeatsSafety Inspection Safety Inspection ChecklistSection Safety Inspection Suggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety PrecautionsSafety Inspection Back Back SectionSection Back Back Angle to Seat Rail TOP END Back Upholstery Figure Adjusting Top End Back UpholsteryReplacing Top End Back Upholstery Section BackAdjustable Tension Straps Custom Manual Adjustable Tension Back Upholstery FigureReplacing Adjustable Tension Back Upholstery Fastening Strap Back Number HoleSection Seat SeatReplacing Custom Manual Screw on Seat Upholstery Seat SectionWheels REMOVING/INSTALLING Rear Wheels FigureSection Wheels Wheels Section Adjusting QUICK-RELEASE Axles FigureAdjusting QUAD-RELEASE Handles Figure Installing QUAD-RELEASE Axles FigureAND/OR OUT Removing Play from Rear Wheels Handrim Replacement FigureOPENING/CLOSING Clamps Figure REPAIRING/REPLACING Rear WHEEL, TIRE/TUBECamber Clamps Receiver Tube Clamps Receiver Tube ClampsCamber Clamps Quick Release Lever Standard Closed Position OpenCamber Tube Adjusting Rear Wheel CamberA4 Camber System Figure Determining TOE TOE OUT Measuring Centerlines of Rear Wheels Determining TOE IN/TOE OUT Figures 8A4 Camber System Adjusting TOE IN/TOE OUTCourse Adjustment Figure Camber Tube 2000 FigureAdjusting TOE IN/TOE OUT A4 Camber System Course Adjustment Adjusting TOE IN/TOE OUT A4 Camber System Fine Adjustment Fine Adjustment FigureTape Showing Adjusting Center of GravityNever Operate Wheelchair with Both Ends of the IndexingWheelbase Width Camber Adjusting Wheelbase WidthTube Camber Replacing Axle Tube FigureFront Wheelchair RearAdjusting the Axle Tube Axle Tube Camber Tube TOE IN/TOE OUT Measurement is not Within ±1/8-INCH TOE IN/TOE OUT Measurement is Within ±1/8-INCHNON-SUSPENSION Caster REPLACING/ADJUSTING Casters FigureSuspension Caster Adjusting Front Caster Height Adjusting Front Caster Height FigureReplacing the High/Low Mount Wheel Lock Wheel Lock ADJUSTMENT/REPLACEMENT FigureAdjusting the High/Low Mount Wheel Lock Wheel Lock AdjustmentFootrest / ANTI-TIPPER ADJUSTING/REPLACING Standard Footrest FigureIf Replacing or Adjusting the Footrest If Replacing the FootrestFootplate Angle Adjustment INSTALLING/ADJUSTING Optional A4 Footrest FigureInstalling AdjustingDepth Footplate Depth AdjustmentReplacement ANTI-TIPPER REPLACEMENT/ADJUSTMENT FigureAdjustment Section Suspension Elastomers and SuspensionReplacing Rear Elastomers Figure SuspensionReplacing Rear Elastomers Suspension SectionDetail C Replacing Front Elastomers FigureDetail B Suspension Tube Hardware REMOVING/INSTALLING/REPLACING Suspension Tubes FigureInstalling Suspension Tubes Removing Suspension TubesAdjusting SEAT-TO Floor Height Adjusting SEAT-TO-FLOOR Height FigureClamp Position Must be INVERTED- Proceed to Step Repositioning the Axle Tube FigureDetail C Axle Tube Positions Procedure SuspensionSide View of Camber Clamp with Quick Release Lever Suspension ProcedureRepositioning Quick Release Levers Figure ReverseTerminator SS Warranty WarrantyCanada