Invacare TerminatorTM SS manual Transferring to and from Other Seats, ESCALATORS? Sorry

Page 13

GENERAL GUIDELINES

SECTION 1

 

 

Follow this procedure for moving the wheelchair between floors when an elevator is NOT available:

1.If equipped, turn the anti-tippers UP. Refer to SECTION 6 in this manual.

2.After the wheelchair has been tilted back to the balance point, one assistant (in the rear) backs the wheelchair up against the first step, while securely grasping a non- removable (non-detachable) part of the wheelchair for leverage.

3.The second assistant, with a firm hold on a non-detachable part of the framework, lifts the wheelchair up and over the stair and steadies it as the first assistant places one foot on the next stair and repeats procedure.

4.The wheelchair should not be lowered until the last stair has been negotiated and it has been rolled away from the stairway.

5.If equipped, turn the anti-tippers DOWN. Refer to SECTION 6 in this manual.

ESCALATORS? SORRY!

DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury may occur.

TRANSFERRING TO AND FROM OTHER SEATS

WARNING

BEFORE attempting to transfer in or out of the wheelchair, every precaution should be taken to reduce the gap distance. Turn both casters parallel to the object you are transferring onto. Also be certain the wheel locks are engaged to help prevent the wheels from moving.

CAUTION

When transferring, position yourself as far back as possible in the seat. This will prevent damaged upholstery and the possibility of the wheelchair tipping forward.

NOTE: This activity may be performed independently provided you have adequate mobility and upper body strength.

Position the wheelchair as close as possible along side the seat to which you are transferring, with the front casters parallel to it. Remove the armrest, if installed. Engage wheel locks. Shift body weight into seat with transfer.

During independent transfer, little or no seat platform will be beneath you. Use a transfer board if at all possible.

GENERAL GUIDELINES

Part No. 1052712 Rev D

13

Terminator™ SS

Image 13
Contents Terminator SS Special Notes Special NotesWheelchair TIE-DOWN Restraints and Seat Positioning Straps Table of Contents Limited Warranty Specifications SpecificationsOperating Information StabilityGeneral Guidelines Section General GuidelinesDo not tip the wheelchair without assistance General Guidelines SectionDo not operate on roads, streets or highways Weight Limitation Weight TrainingTire Pressure and Information Stability and Balance SAFETY/HANDLING of WheelchairsCoping with Everyday Obstacles Unoccupied Occupied Percentage of Weight DistributionShortening Lengthening REACHING, Leaning Bending Forward TippingREACHING, Leaning Backwards Stairways Tipping CurbsESCALATORS? Sorry Transferring to and from Other SeatsSafety Inspection Safety Inspection ChecklistSection Safety Inspection Maintenance TroubleshootingMaintenance Safety Precautions Suggested Maintenance ProceduresSafety Inspection Back Back SectionSection Back Back Angle to Seat Rail TOP END Back Upholstery Figure Adjusting Top End Back UpholsteryReplacing Top End Back Upholstery Section BackAdjustable Tension Straps Custom Manual Adjustable Tension Back Upholstery FigureReplacing Adjustable Tension Back Upholstery Fastening Strap Back Number HoleSection Seat SeatReplacing Custom Manual Screw on Seat Upholstery Seat SectionWheels REMOVING/INSTALLING Rear Wheels FigureSection Wheels Wheels Section Adjusting QUICK-RELEASE Axles FigureAdjusting QUAD-RELEASE Handles Figure Installing QUAD-RELEASE Axles FigureAND/OR OUT Removing Play from Rear Wheels Handrim Replacement FigureOPENING/CLOSING Clamps Figure REPAIRING/REPLACING Rear WHEEL, TIRE/TUBECamber Clamps Camber Clamps Quick Release Lever Standard Closed Position Receiver Tube ClampsOpen Receiver Tube ClampsCamber Tube Adjusting Rear Wheel CamberA4 Camber System Figure Determining TOE TOE OUT Measuring Centerlines of Rear Wheels Determining TOE IN/TOE OUT Figures 8Course Adjustment Figure Adjusting TOE IN/TOE OUTCamber Tube 2000 Figure A4 Camber SystemAdjusting TOE IN/TOE OUT A4 Camber System Course Adjustment Adjusting TOE IN/TOE OUT A4 Camber System Fine Adjustment Fine Adjustment FigureNever Operate Wheelchair with Both Adjusting Center of GravityEnds of the Indexing Tape ShowingWheelbase Width Camber Adjusting Wheelbase WidthTube Front Wheelchair Replacing Axle Tube FigureRear CamberAdjusting the Axle Tube Axle Tube Camber Tube TOE IN/TOE OUT Measurement is not Within ±1/8-INCH TOE IN/TOE OUT Measurement is Within ±1/8-INCHNON-SUSPENSION Caster REPLACING/ADJUSTING Casters FigureSuspension Caster Adjusting Front Caster Height Adjusting Front Caster Height FigureAdjusting the High/Low Mount Wheel Lock Wheel Lock ADJUSTMENT/REPLACEMENT FigureWheel Lock Adjustment Replacing the High/Low Mount Wheel LockIf Replacing or Adjusting the Footrest ADJUSTING/REPLACING Standard Footrest FigureIf Replacing the Footrest Footrest / ANTI-TIPPERInstalling INSTALLING/ADJUSTING Optional A4 Footrest FigureAdjusting Footplate Angle AdjustmentDepth Footplate Depth AdjustmentReplacement ANTI-TIPPER REPLACEMENT/ADJUSTMENT FigureAdjustment Replacing Rear Elastomers Figure Elastomers and SuspensionSuspension Section SuspensionReplacing Rear Elastomers Suspension SectionDetail C Replacing Front Elastomers FigureInstalling Suspension Tubes REMOVING/INSTALLING/REPLACING Suspension Tubes FigureRemoving Suspension Tubes Detail B Suspension Tube HardwareAdjusting SEAT-TO Floor Height Adjusting SEAT-TO-FLOOR Height FigureClamp Position Must be INVERTED- Proceed to Step Repositioning the Axle Tube FigureDetail C Axle Tube Positions Procedure SuspensionRepositioning Quick Release Levers Figure Suspension ProcedureReverse Side View of Camber Clamp with Quick Release LeverTerminator SS Warranty WarrantyCanada