Invacare TerminatorTM SS manual Adjusting TOE IN/TOE OUT A4 Camber System Course Adjustment

Page 35

WHEELS

SECTION 5

 

 

5.Measure the distance between the center lines at the rear and front of the rear wheels at approximately 12-inches from the ground/floor. Refer to DETERMINING TOE IN/TOE OUT in this section of the manual.

6.Repeat STEPS 1-4 until the toe in/toe out measurement is less than 1/2-inch (0 + 1/ 4-inch for maximum rollability).

7.Rotate either the right or left adjustment ring until the stop on the ring is at the top of the slot in the camber clamp as shown in FIGURE 11 and securely tighten the phillips screw on the positioned adjustment ring.

NOTE: DO NOT tighten the phillips screw on the other adjustment ring at this time.

NOTE: Repeat STEPS 1-7 of this procedure for the other adjustment ring AFTER repositioning the camber insert. Refer to ADJUSTING REAR WHEEL CAMBER in this section of the manual.

NOTE: When positioning the other adjustment ring, rotate the ring until the stop is at the bottom of the slot in the camber clamp. The right and left stops MUST be positioned opposite of each other or the FINE ADJUSTMENT in this section of the manual will not work correctly.

NOTE: When the left adjustment ring is adjusted to a camber, the right adjustment ring will not touch the camber clamp and when the right adjustment ring is adjusted to the other camber the left adjustment ring will not touch the camber clamp.

NOTE: Rear wheels removed from the drawings

Axle Tube - Rotates Up and Down

for clarity, There is no need to remove rear

 

wheels from the wheelchair during adjustment.

 

NOTE: Below are two (2) examples of how the adjustment rings can be positioned.

Adjustment Ring

Phillips Screw

 

Stop - Not touching

Adjustment Ring

 

camber clamp

Stop - In position for

 

one (1) camber,

Phillips Screw

touching camber clamp

 

Camber Clamp

Camber Clamp

Adjustment Ring

 

Stop - In position for

Adjustment Ring

 

one (1) camber,

Stop - Not touching

touching camber clamp

camber clamp

 

FIGURE 11 - ADJUSTING TOE IN/TOE OUT - A4 CAMBER SYSTEM -

COURSE ADJUSTMENT

WHEELS

Part No. 1052712 Rev D

35

Terminator™ SS

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Terminator SS Wheelchair TIE-DOWN Restraints and Seat Positioning Straps Special NotesSpecial Notes Table of Contents Limited Warranty Specifications SpecificationsSection General Guidelines StabilityOperating Information General GuidelinesDo not operate on roads, streets or highways General Guidelines SectionDo not tip the wheelchair without assistance Tire Pressure and Information Weight TrainingWeight Limitation Coping with Everyday Obstacles SAFETY/HANDLING of WheelchairsStability and Balance Shortening Lengthening Percentage of Weight DistributionUnoccupied Occupied REACHING, Leaning Backwards TippingREACHING, Leaning Bending Forward Stairways Tipping CurbsESCALATORS? Sorry Transferring to and from Other SeatsSection Safety Inspection Safety Inspection ChecklistSafety Inspection Suggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety PrecautionsSafety Inspection Back Back SectionSection Back Back Angle to Seat Rail TOP END Back Upholstery Figure Adjusting Top End Back UpholsteryReplacing Top End Back Upholstery Section BackReplacing Adjustable Tension Back Upholstery Custom Manual Adjustable Tension Back Upholstery FigureAdjustable Tension Straps Fastening Strap Back Number HoleSection Seat SeatReplacing Custom Manual Screw on Seat Upholstery Seat SectionSection Wheels REMOVING/INSTALLING Rear Wheels FigureWheels Wheels Section Adjusting QUICK-RELEASE Axles FigureAND/OR OUT Installing QUAD-RELEASE Axles FigureAdjusting QUAD-RELEASE Handles Figure Removing Play from Rear Wheels Handrim Replacement FigureCamber Clamps REPAIRING/REPLACING Rear WHEEL, TIRE/TUBEOPENING/CLOSING Clamps Figure Receiver Tube Clamps Receiver Tube ClampsCamber Clamps Quick Release Lever Standard Closed Position OpenA4 Camber System Figure Adjusting Rear Wheel CamberCamber Tube Determining TOE TOE OUT Measuring Centerlines of Rear Wheels Determining TOE IN/TOE OUT Figures 8A4 Camber System Adjusting TOE IN/TOE OUTCourse Adjustment Figure Camber Tube 2000 FigureAdjusting TOE IN/TOE OUT A4 Camber System Course Adjustment Adjusting TOE IN/TOE OUT A4 Camber System Fine Adjustment Fine Adjustment FigureTape Showing Adjusting Center of GravityNever Operate Wheelchair with Both Ends of the IndexingTube Adjusting Wheelbase WidthWheelbase Width Camber Camber Replacing Axle Tube FigureFront Wheelchair RearAdjusting the Axle Tube Axle Tube Camber Tube TOE IN/TOE OUT Measurement is not Within ±1/8-INCH TOE IN/TOE OUT Measurement is Within ±1/8-INCHSuspension Caster REPLACING/ADJUSTING Casters FigureNON-SUSPENSION Caster Adjusting Front Caster Height Adjusting Front Caster Height FigureReplacing the High/Low Mount Wheel Lock Wheel Lock ADJUSTMENT/REPLACEMENT FigureAdjusting the High/Low Mount Wheel Lock Wheel Lock AdjustmentFootrest / ANTI-TIPPER ADJUSTING/REPLACING Standard Footrest FigureIf Replacing or Adjusting the Footrest If Replacing the FootrestFootplate Angle Adjustment INSTALLING/ADJUSTING Optional A4 Footrest FigureInstalling AdjustingDepth Footplate Depth AdjustmentAdjustment ANTI-TIPPER REPLACEMENT/ADJUSTMENT FigureReplacement Section Suspension Elastomers and SuspensionReplacing Rear Elastomers Figure SuspensionReplacing Rear Elastomers Suspension SectionDetail C Replacing Front Elastomers FigureDetail B Suspension Tube Hardware REMOVING/INSTALLING/REPLACING Suspension Tubes FigureInstalling Suspension Tubes Removing Suspension TubesAdjusting SEAT-TO Floor Height Adjusting SEAT-TO-FLOOR Height FigureClamp Position Must be INVERTED- Proceed to Step Repositioning the Axle Tube FigureDetail C Axle Tube Positions Procedure SuspensionSide View of Camber Clamp with Quick Release Lever Suspension ProcedureRepositioning Quick Release Levers Figure ReverseTerminator SS Warranty WarrantyCanada
Top Page Image Contents