Invacare TerminatorTM SS manual Suspension Section, Replacing Rear Elastomers

Page 51

SUSPENSION	SECTION 7

4. Install the locknut onto the mounting bolt.

NOTE: It may be necessary to compress the rear suspension system to install the locknut onto the mounting bolt.

5.Tighten the locknut until three (3) threads can be seen on the end of mounting bolt.

6.Ensure wheel locks engage properly. Refer to WHEEL LOCK ADJUSTMENT/REPLACEMENT in SECTION 5 of the manual.

Telescoping Tube	Mounting Bolt
	Nylon Washer
	Suspension Arm

UPPER Elastomer

Recessed Spacer

LOWER Elastomer

Nylon Washer

Locknut

FIGURE 1 - REPLACING REAR ELASTOMERS

SUSPENSION

Part No. 1052712 Rev D

51

Terminator™ SS

Image 51

Contents Terminator SS Special Notes Special NotesWheelchair TIE-DOWN Restraints and Seat Positioning Straps Table of Contents Limited Warranty Specifications SpecificationsSection General Guidelines StabilityOperating Information General GuidelinesGeneral Guidelines Section Do not tip the wheelchair without assistanceDo not operate on roads, streets or highways Weight Training Weight LimitationTire Pressure and Information SAFETY/HANDLING of Wheelchairs Stability and BalanceCoping with Everyday Obstacles Percentage of Weight Distribution Unoccupied OccupiedShortening Lengthening Tipping REACHING, Leaning Bending ForwardREACHING, Leaning Backwards Stairways Tipping CurbsESCALATORS? Sorry Transferring to and from Other SeatsSafety Inspection Checklist Safety InspectionSection Safety Inspection Suggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety PrecautionsSafety Inspection Back Back SectionSection Back Back Angle to Seat Rail TOP END Back Upholstery Figure Adjusting Top End Back UpholsteryReplacing Top End Back Upholstery Section BackCustom Manual Adjustable Tension Back Upholstery Figure Adjustable Tension StrapsReplacing Adjustable Tension Back Upholstery Fastening Strap Back Number HoleSection Seat SeatReplacing Custom Manual Screw on Seat Upholstery Seat SectionREMOVING/INSTALLING Rear Wheels Figure WheelsSection Wheels Wheels Section Adjusting QUICK-RELEASE Axles FigureInstalling QUAD-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles FigureAND/OR OUT Removing Play from Rear Wheels Handrim Replacement FigureREPAIRING/REPLACING Rear WHEEL, TIRE/TUBE OPENING/CLOSING Clamps FigureCamber Clamps Receiver Tube Clamps Receiver Tube ClampsCamber Clamps Quick Release Lever Standard Closed Position OpenAdjusting Rear Wheel Camber Camber TubeA4 Camber System Figure Determining TOE TOE OUT Measuring Centerlines of Rear Wheels Determining TOE IN/TOE OUT Figures 8A4 Camber System Adjusting TOE IN/TOE OUTCourse Adjustment Figure Camber Tube 2000 FigureAdjusting TOE IN/TOE OUT A4 Camber System Course Adjustment Adjusting TOE IN/TOE OUT A4 Camber System Fine Adjustment Fine Adjustment FigureTape Showing Adjusting Center of GravityNever Operate Wheelchair with Both Ends of the IndexingAdjusting Wheelbase Width Wheelbase Width CamberTube Camber Replacing Axle Tube FigureFront Wheelchair RearAdjusting the Axle Tube Axle Tube Camber Tube TOE IN/TOE OUT Measurement is not Within ±1/8-INCH TOE IN/TOE OUT Measurement is Within ±1/8-INCHREPLACING/ADJUSTING Casters Figure NON-SUSPENSION CasterSuspension Caster Adjusting Front Caster Height Adjusting Front Caster Height FigureReplacing the High/Low Mount Wheel Lock Wheel Lock ADJUSTMENT/REPLACEMENT FigureAdjusting the High/Low Mount Wheel Lock Wheel Lock AdjustmentFootrest / ANTI-TIPPER ADJUSTING/REPLACING Standard Footrest FigureIf Replacing or Adjusting the Footrest If Replacing the FootrestFootplate Angle Adjustment INSTALLING/ADJUSTING Optional A4 Footrest FigureInstalling AdjustingDepth Footplate Depth AdjustmentANTI-TIPPER REPLACEMENT/ADJUSTMENT Figure ReplacementAdjustment Section Suspension Elastomers and SuspensionReplacing Rear Elastomers Figure SuspensionReplacing Rear Elastomers Suspension SectionDetail C Replacing Front Elastomers FigureDetail B Suspension Tube Hardware REMOVING/INSTALLING/REPLACING Suspension Tubes FigureInstalling Suspension Tubes Removing Suspension TubesAdjusting SEAT-TO Floor Height Adjusting SEAT-TO-FLOOR Height FigureClamp Position Must be INVERTED- Proceed to Step Repositioning the Axle Tube FigureDetail C Axle Tube Positions Procedure SuspensionSide View of Camber Clamp with Quick Release Lever Suspension ProcedureRepositioning Quick Release Levers Figure ReverseTerminator SS Warranty WarrantyCanada