Invacare TerminatorTM SS manual Fastening Strap

Page 22

BACK

SECTION 3

BACK

 

 

WARNING

After the adjustable tension back upholstery has been positioned to the end-users individual needs, the fastening straps MUST be securely fastened BEFORE applying the back upholstery cover. The adjustable back should be checked whenever entering the wheelchair to ensure that the fastening straps are securely fastened.

9.Secure the back upholstery cover (fastening strap) to the back of the adjustable back upholstery (fastening strap).

10.Flip the back upholstery cover over the adjustable back upholstery and secure the fastening straps to the front of the adjustable back upholstery.

11.Lay the front portion of the back upholstery cover on the seat pan.

12.Adjust the slack in the back upholstery cover and then secure to the seat pan fasten- ing straps.

Fastening Strap

Back Upholstery Cover

 

 

Fastening Straps

Back Cane

 

 

Back

Adjuster Strap

 

 

Upright

Anchor

Back

 

Loop

Back Height

 

Cane

 

Upper

Adjustment Screw

 

Back Upholstery

 

Grommet

 

Hole

Anchor Loop Section

 

 

Mounting Screw

Back Upholstery Adjuster Strap Section

FIGURE 4 - ADJUSTING/REPLACING BACK UPHOLSTERY - CUSTOM

MANUAL ADJUSTABLE TENSION BACK UPHOLSTERY

Terminator™ SS

22

Part No. 1052712 Rev D

Image 22
Contents Terminator SS Special Notes Special NotesWheelchair TIE-DOWN Restraints and Seat Positioning Straps Table of Contents Limited Warranty Specifications SpecificationsGeneral Guidelines StabilityOperating Information Section General GuidelinesDo not tip the wheelchair without assistance General Guidelines SectionDo not operate on roads, streets or highways Weight Limitation Weight TrainingTire Pressure and Information Stability and Balance SAFETY/HANDLING of WheelchairsCoping with Everyday Obstacles Unoccupied Occupied Percentage of Weight DistributionShortening Lengthening REACHING, Leaning Bending Forward TippingREACHING, Leaning Backwards Tipping Curbs StairwaysTransferring to and from Other Seats ESCALATORS? SorrySafety Inspection Safety Inspection ChecklistSection Safety Inspection Maintenance Safety Precautions TroubleshootingMaintenance Suggested Maintenance ProceduresSafety Inspection Back Section BackSection Back Back Angle to Seat Rail Adjusting Top End Back Upholstery TOP END Back Upholstery FigureSection Back Replacing Top End Back UpholsteryAdjustable Tension Straps Custom Manual Adjustable Tension Back Upholstery FigureReplacing Adjustable Tension Back Upholstery Fastening Strap Hole Back NumberSeat Section SeatSeat Section Replacing Custom Manual Screw on Seat UpholsteryWheels REMOVING/INSTALLING Rear Wheels FigureSection Wheels Adjusting QUICK-RELEASE Axles Figure Wheels SectionAdjusting QUAD-RELEASE Handles Figure Installing QUAD-RELEASE Axles FigureAND/OR OUT Handrim Replacement Figure Removing Play from Rear WheelsOPENING/CLOSING Clamps Figure REPAIRING/REPLACING Rear WHEEL, TIRE/TUBECamber Clamps Open Receiver Tube ClampsCamber Clamps Quick Release Lever Standard Closed Position Receiver Tube ClampsCamber Tube Adjusting Rear Wheel CamberA4 Camber System Figure Determining TOE IN/TOE OUT Figures 8 Determining TOE TOE OUT Measuring Centerlines of Rear WheelsCamber Tube 2000 Figure Adjusting TOE IN/TOE OUTCourse Adjustment Figure A4 Camber SystemAdjusting TOE IN/TOE OUT A4 Camber System Course Adjustment Fine Adjustment Figure Adjusting TOE IN/TOE OUT A4 Camber System Fine AdjustmentEnds of the Indexing Adjusting Center of GravityNever Operate Wheelchair with Both Tape ShowingWheelbase Width Camber Adjusting Wheelbase WidthTube Rear Replacing Axle Tube FigureFront Wheelchair CamberAdjusting the Axle Tube Axle Tube Camber Tube TOE IN/TOE OUT Measurement is Within ±1/8-INCH TOE IN/TOE OUT Measurement is not Within ±1/8-INCHNON-SUSPENSION Caster REPLACING/ADJUSTING Casters FigureSuspension Caster Adjusting Front Caster Height Figure Adjusting Front Caster HeightWheel Lock Adjustment Wheel Lock ADJUSTMENT/REPLACEMENT FigureAdjusting the High/Low Mount Wheel Lock Replacing the High/Low Mount Wheel LockIf Replacing the Footrest ADJUSTING/REPLACING Standard Footrest FigureIf Replacing or Adjusting the Footrest Footrest / ANTI-TIPPERAdjusting INSTALLING/ADJUSTING Optional A4 Footrest FigureInstalling Footplate Angle AdjustmentFootplate Depth Adjustment DepthReplacement ANTI-TIPPER REPLACEMENT/ADJUSTMENT FigureAdjustment Suspension Elastomers and SuspensionReplacing Rear Elastomers Figure Section SuspensionSuspension Section Replacing Rear ElastomersReplacing Front Elastomers Figure Detail CRemoving Suspension Tubes REMOVING/INSTALLING/REPLACING Suspension Tubes FigureInstalling Suspension Tubes Detail B Suspension Tube HardwareAdjusting SEAT-TO-FLOOR Height Figure Adjusting SEAT-TO Floor HeightRepositioning the Axle Tube Figure Clamp Position Must be INVERTED- Proceed to StepProcedure Suspension Detail C Axle Tube PositionsReverse Suspension ProcedureRepositioning Quick Release Levers Figure Side View of Camber Clamp with Quick Release LeverTerminator SS Warranty WarrantyCanada