Invacare TerminatorTM SS manual Adjusting QUICK-RELEASE Axles Figure, Wheels Section

Page 27

WHEELS	SECTION 5

WARNING

Pull on the rear wheel to make sure the detent pin and locking pins of the quick/quad-release axle are fully released BEFORE operating wheelchair.

Keep locking pins clean.

4.If there is too much movement of the rear wheel assembly in a back and forth motion, refer to ADJUSTING QUICK-RELEASE AXLES or ADJUSTING QUAD-RELEASE HANDLES in this section of the manual.

	Locking Pins		Wheelchair
		Quick-Release	Wheelchair
		Quick-Release	Frame
Detent Pin		Axle	Frame
		Axle

			Rear Wheel

NOTE: Quad-Release Axle not shown. Locking pins the same as Quick-Release Axle.

FIGURE 1 - REMOVING/INSTALLING REAR WHEELS

ADJUSTING QUICK-RELEASE AXLES (FIGURE 2)

1.Remove rear wheel and quick-release axle from the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual.

2.Depress detent pin in the quick-release axle and slide axle through the wheel hub.

3.Release detent pin ensuring that the locking pins are fully released.

4.Increase or decrease end play by adjusting the locknut on the end of the quick-release axle.

5.Reinstall rear wheel onto the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual.

WHEELS

Adjustable Axle Position

Camber Bar

Locking Pins

NOTE: End of Quick Release axle is shown for reference only. It is not visible when inserted into camber bar

Locknut

Detent Pin

Wheel Hub

Quick Release Axle

FIGURE 2- ADJUSTING QUICK-RELEASE AXLES

Part No. 1052712 Rev D

27

Terminator™ SS

Image 27

Contents Terminator SS Special Notes Special NotesWheelchair TIE-DOWN Restraints and Seat Positioning Straps Table of Contents Limited Warranty Specifications SpecificationsSection General Guidelines StabilityOperating Information General GuidelinesGeneral Guidelines Section Do not tip the wheelchair without assistanceDo not operate on roads, streets or highways Weight Training Weight LimitationTire Pressure and Information SAFETY/HANDLING of Wheelchairs Stability and BalanceCoping with Everyday Obstacles Percentage of Weight Distribution Unoccupied OccupiedShortening Lengthening Tipping REACHING, Leaning Bending ForwardREACHING, Leaning Backwards Stairways Tipping CurbsESCALATORS? Sorry Transferring to and from Other SeatsSafety Inspection Checklist Safety InspectionSection Safety Inspection Suggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety PrecautionsSafety Inspection Back Back SectionSection Back Back Angle to Seat Rail TOP END Back Upholstery Figure Adjusting Top End Back UpholsteryReplacing Top End Back Upholstery Section BackCustom Manual Adjustable Tension Back Upholstery Figure Adjustable Tension StrapsReplacing Adjustable Tension Back Upholstery Fastening Strap Back Number HoleSection Seat SeatReplacing Custom Manual Screw on Seat Upholstery Seat SectionREMOVING/INSTALLING Rear Wheels Figure WheelsSection Wheels Wheels Section Adjusting QUICK-RELEASE Axles FigureInstalling QUAD-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles FigureAND/OR OUT Removing Play from Rear Wheels Handrim Replacement FigureREPAIRING/REPLACING Rear WHEEL, TIRE/TUBE OPENING/CLOSING Clamps FigureCamber Clamps Receiver Tube Clamps Receiver Tube ClampsCamber Clamps Quick Release Lever Standard Closed Position OpenAdjusting Rear Wheel Camber Camber TubeA4 Camber System Figure Determining TOE TOE OUT Measuring Centerlines of Rear Wheels Determining TOE IN/TOE OUT Figures 8A4 Camber System Adjusting TOE IN/TOE OUTCourse Adjustment Figure Camber Tube 2000 FigureAdjusting TOE IN/TOE OUT A4 Camber System Course Adjustment Adjusting TOE IN/TOE OUT A4 Camber System Fine Adjustment Fine Adjustment FigureTape Showing Adjusting Center of GravityNever Operate Wheelchair with Both Ends of the IndexingAdjusting Wheelbase Width Wheelbase Width CamberTube Camber Replacing Axle Tube FigureFront Wheelchair RearAdjusting the Axle Tube Axle Tube Camber Tube TOE IN/TOE OUT Measurement is not Within ±1/8-INCH TOE IN/TOE OUT Measurement is Within ±1/8-INCHREPLACING/ADJUSTING Casters Figure NON-SUSPENSION CasterSuspension Caster Adjusting Front Caster Height Adjusting Front Caster Height FigureReplacing the High/Low Mount Wheel Lock Wheel Lock ADJUSTMENT/REPLACEMENT FigureAdjusting the High/Low Mount Wheel Lock Wheel Lock AdjustmentFootrest / ANTI-TIPPER ADJUSTING/REPLACING Standard Footrest FigureIf Replacing or Adjusting the Footrest If Replacing the FootrestFootplate Angle Adjustment INSTALLING/ADJUSTING Optional A4 Footrest FigureInstalling AdjustingDepth Footplate Depth AdjustmentANTI-TIPPER REPLACEMENT/ADJUSTMENT Figure ReplacementAdjustment Section Suspension Elastomers and SuspensionReplacing Rear Elastomers Figure SuspensionReplacing Rear Elastomers Suspension SectionDetail C Replacing Front Elastomers FigureDetail B Suspension Tube Hardware REMOVING/INSTALLING/REPLACING Suspension Tubes FigureInstalling Suspension Tubes Removing Suspension TubesAdjusting SEAT-TO Floor Height Adjusting SEAT-TO-FLOOR Height FigureClamp Position Must be INVERTED- Proceed to Step Repositioning the Axle Tube FigureDetail C Axle Tube Positions Procedure SuspensionSide View of Camber Clamp with Quick Release Lever Suspension ProcedureRepositioning Quick Release Levers Figure ReverseTerminator SS Warranty WarrantyCanada