Invacare 1073955 manual Removing Bilateral Contracture Platform

Page 36

SECTION 5—FRONT RIGGINGS

4.Secure the bilateral contracture platform to the seat frame in the mounting position shown in FIGURE 5.10 with the mounting screws and washers provided. Securely tighten.

5.Adjust the bilateral contracture platform to the desired height, angle and depth. Refer to Adjusting Height of Bilateral Contracture Platform on page 36.

6.Install end caps on seat rail.

Removing Bilateral Contracture Platform

1.Remove the mounting screws and washers that secure the bilateral contracture platform to the seat frame.

2.Remove the bilateral contracture platform from the wheelchair.

3.Remove the end caps in the seat rails.

4.Install telescoping tubes. Refer to Installing/Removing/Adjusting the Telescoping Front Frame Tubes on page 38.

5.Install desired footrest. Refer to Installing/Removing Front Riggings on page 30.

Bilateral

Contracture Washer

Seat Platform

Rail

End Cap

Upper

Support

Mounting

Screw

Locknut

Mounting

Screw

 

Spacers

FIGURE 5.10 Bilateral Contracture

Platform Procedures

Adjusting Height of Bilateral Contracture Platform

NOTE: For this procedure, refer to FIGURE 5.11 on page 37.

NOTE: The bilateral contracture platform has six height adjustment options with a range of 11‐16‐inches in height.

1.Remove the mounting screw, spacers and locknut that secure the bilateral contracture platform to the upper support.

2.Slide the bilateral contracture platform up or down to the necessary height.

3.Reinstall the mounting screw, spacers, and locknuts.

4.Securely tighten the mounting screw and locknut that secure the contracture platform to the upper support. Repeat for opposite platform.

Orbit

36

Part No. 1073955

Image 36
Contents Orbit Orbit Table of Contents Front Riggings Options Register Your Product Complete and mail the form on the nextProduct Registration Form City State/ProvinceFold here Cut Along Line Special Notes Wheelchair TIE-DOWN Restraints and Seat RestraintsLabel Location Standard LabelsWheelchairs with Trro Typical Product Parameters Minimum MaximumGeneral Guidelines Information for Healthcare Professionals/AssistantsStability All Models Anti-Tippers Operating InformationWeight Training Weight LimitationTire Pressure SAFETY/HANDLING of Wheelchairs Safety/Handling of WheelchairsStability and Balance Coping With Everyday Obstacles Reaching, Leaning and Bending Forward Reaching and Leaning BackwardsTipping Do not tip the wheelchair without assistanceMethod 1 Wheelchair With Step Tubes Method 2 Wheelchair Without Step TubesStairways StairwaysEscalators Transferring To and From Other SeatsSafety INSPECTION/TROUBLESHOOTING Safety Inspection ChecklistInspect/Adjust Initially Inspect/Adjust Weekly Inspect/Adjust MonthlyInspect/Adjust Periodically Troubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance ProceduresSafety INSPECTION/TROUBLESHOOTING Assembly Assembling/Disassembling the Removable Orbit WheelchairAssembling the Seat Frame to the Base Frame Disassembling the Seat Frame from the Base Frame Assembling/Disassembling the Removable Orbit Wheelchair Installing/Removing Front Riggings Installing Front RiggingsFront Riggings Removing Front RiggingsAdjusting Footplate Height Adjusting Pivot Slide Tube HeightAdjusting Footplate Height 70 MFX and 90 Footrests Only Installing 3-Inch Extension Adjusting Footplate Height MFX and 90 Footrests OnlyInstalling Elevating Legrest Adjusting Elevating LegrestInstalling Adjustable Angle Flip-up Footplate Adjusting Depth on Adjustable Angle Flip-UpAdjusting Angle on Adjustable Angle Flip-up Footplate Bilateral Contracture Platform Procedures Installing Bilateral Contracture PlatformAdjusting Height of Bilateral Contracture Platform Removing Bilateral Contracture PlatformAdjusting Bilateral Contracture Platform Angle Adjusting Bilateral Contracture Platform Footplate DepthReplacing Sector Block Installing/Removing Telescoping Front Frame Tubes Adjusting Telescoping Front Frame TubesOptional Footrest Accessories Replacing Heel LoopComposite Footplates Adjustable Footplate 15 Replacing Heel Loop Adjustable FootplateInstalling the T-Arm Sockets ArmsInstalling/Removing the T-arms Installing T-ArmsRemoving T-Arms Adjusting the T-Arms Adjusting T-Arm HeightAdjusting T-Arm Width Adjusting T-Arm Depth Adjusting the T-Arms- Adjusting T-Arm WidthAdjusting T-Arm Sockets Adjusting the T-Arms- Adjusting T-Arm DepthAdjusting the Transfer Assists and/or Side Guards Adjusting the T-Arms- Adjusting T-Arm SocketsAdjusting the Transfer Assists and/or Side Guards Replacing the T-Arm Locking LeverUsing/Installing/Adjusting Cantilever Arms Using Catilever ArmsInstalling/Removing/Adjusting Catilever Arms Using/Installing/Adjusting Cantilever ArmsAngled Portion Locking Mechanism Replacing and Adjusting Arm Pad Depth for Cantilever Arms AdjustmentReplacement Seat and Back Replacing the Locking Mechanism in the Back CaneInstalling Fixed Height Stroller Handles Installing Adjustable Angle Stroller HandlesRemoving Adjustable Angle Stroller Handles Adjusting Adjustable Angle Stroller HandlesRemoving/Installing the Spreader Bar Adjusting Adjustable Angle Stroller HandlesRemoving/Installing the Spreader Bar Folding/Unfolding the Back CanesInstalling RemovingReplacing/Installing Front Caster Assemblies Front CastersReplacing Front Fork Replacing Front ForkAdjusting Caster Headtubes Adjusting Caster HeadtubesRemoving/Installing Rear Wheels Rear WheelsQuick-Release Axles Permanent AxlesAdjusting the Quick-Release Axle Removing/Installing Rear WheelsInstalling Non-Projection Handrims Replacing HandrimsNon-Projection Handrims Projection HandrimsInstalling Projection Handrims Removing Projection HandrimsFoot Activated Wheel Lock Procedures Installing/Removing Foot Activated Wheel LocksUsing Foot Activated Wheel Locks ANTI-TIPPERS/WHEEL LocksHand Activated Wheel Lock Procedures Installing/Removing Hand Activated Wheel LocksAdjusting the Wheel Lock Engaging/Disengaging Hand Activated Wheel LocksInstalling Anti-Tippers Adjusting the Wheel LockAdjusting Anti-Tippers Adjusting Anti-TippersRecliner Engaging Tilt-In-SpaceRecliner Operating Recliner Engaging Tilt-In-SpaceAdjusting Limit Stops of the Tilt Mechanism Adjusting Anterior Forward Limit StopsAdjusting Posterior Rearward Limit Stops Replacing Upholstery Recliner Models OnlyReplacing the Back Upholstery Replacing the Headrest UpholsteryAdjusting the Back Height Recliner Models Only Replacing Upholstery Recliner Models OnlyTransport Ready Option Specifications Weight LimitAbout Transport Ready Packages Compliance InformationSecuring the Wheelchair to the Vehicle Positioning the Wheelchair in the VehicleSecurement Points Securing the WheelchairSecuring the Occupant Vehicle-Anchored BeltsSeating System Positioning Belts Positioning BeltsUsing the Ventilator Tray OptionsLimited Warranty USA