Invacare 1073955 manual Recliner, Engaging Tilt-In-Space

Page 70

SECTION 11—RECLINER

SECTION 11—RECLINER

WARNING

After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur.

Engaging Tilt-In-Space

WARNING

After ANY adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise, injury may result.

ALWAYS make sure that the wheelchair is stable before using the tilt-in-space and/or recline option.

Make sure the occupant of the wheelchair is properly positioned in the wheelchair before using the tilt-in-space, reclining or inclining (reverse recline) to maintain maximum stability and safety. Refer to Safety/Handling of Wheelchairs on page 16.

The Orbit wheelchair MUST be operated by an Assistant when in any tilt or reclined position.

Always engage both wheel locks while using the tilt-in-space, reclining or inclining (reverse recline) the wheelchair.

ALWAYS wear your seat positioning strap. Inasmuch as the seat positioning strap is an option on this wheelchair (you may order with or without the seat positioning strap), Invacare strongly recommends ordering the seat positioning strap as an additional safeguard for the wheelchair user. The seat positioning strap is a positioning belt only. It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts. If signs of wear appear, belt must be replaced immediately.

The seat positioning strap is a positioning belt only. It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts. If signs of wear appear, seat positioning strap MUST be replaced immediately.

DO NOT use the release pedal of the tilt mechanism to gain leverage in tipping the wheelchair. The release pedal was not designed to be used in this manner and may cause injury to the assistant and/or user or damage to the wheelchair.

Both gas cylinders MUST be operational and adjusted properly before using recliner. DO NOT operate the recliner option if only one of the gas cylinders is operational or adjusted properly.

Pinch Points exist between spreader bar and gas cylinders. Use caution, otherwise injury may occur.

When returning the occupant of the wheelchair to the full upright position, more body strength will be required for approximately the last twenty degrees of incline (reverse recline). Make sure to use proper body mechanics (use your legs) or seek assistance to avoid injury.

Orbit

70

Part No. 1073955

Image 70
Contents Orbit Orbit Table of Contents Front Riggings Options Register Your Product Complete and mail the form on the nextProduct Registration Form City State/ProvinceFold here Cut Along Line Special Notes Wheelchair TIE-DOWN Restraints and Seat RestraintsLabel Location Standard LabelsWheelchairs with Trro Typical Product Parameters Minimum MaximumInformation for Healthcare Professionals/Assistants General GuidelinesStability All Models Anti-Tippers Operating InformationWeight Limitation Weight TrainingTire Pressure Safety/Handling of Wheelchairs SAFETY/HANDLING of WheelchairsStability and Balance Coping With Everyday Obstacles Tipping Reaching, Leaning and Bending ForwardReaching and Leaning Backwards Do not tip the wheelchair without assistanceMethod 1 Wheelchair With Step Tubes Method 2 Wheelchair Without Step TubesStairways StairwaysEscalators Transferring To and From Other SeatsSafety Inspection Checklist Safety INSPECTION/TROUBLESHOOTINGInspect/Adjust Initially Inspect/Adjust Weekly Inspect/Adjust MonthlyInspect/Adjust Periodically Maintenance Safety Precautions TroubleshootingMaintenance Suggested Maintenance ProceduresSafety INSPECTION/TROUBLESHOOTING Assembling/Disassembling the Removable Orbit Wheelchair AssemblyAssembling the Seat Frame to the Base Frame Disassembling the Seat Frame from the Base Frame Assembling/Disassembling the Removable Orbit Wheelchair Front Riggings Installing/Removing Front RiggingsInstalling Front Riggings Removing Front RiggingsAdjusting Pivot Slide Tube Height Adjusting Footplate HeightAdjusting Footplate Height 70 MFX and 90 Footrests Only Installing 3-Inch Extension Adjusting Footplate Height MFX and 90 Footrests OnlyInstalling Elevating Legrest Adjusting Elevating LegrestAdjusting Depth on Adjustable Angle Flip-Up Installing Adjustable Angle Flip-up FootplateAdjusting Angle on Adjustable Angle Flip-up Footplate Bilateral Contracture Platform Procedures Installing Bilateral Contracture PlatformAdjusting Height of Bilateral Contracture Platform Removing Bilateral Contracture PlatformAdjusting Bilateral Contracture Platform Footplate Depth Adjusting Bilateral Contracture Platform AngleReplacing Sector Block Installing/Removing Telescoping Front Frame Tubes Adjusting Telescoping Front Frame TubesReplacing Heel Loop Optional Footrest AccessoriesComposite Footplates Adjustable Footplate 15 Replacing Heel Loop Adjustable FootplateInstalling the T-Arm Sockets ArmsInstalling T-Arms Installing/Removing the T-armsRemoving T-Arms Adjusting T-Arm Height Adjusting the T-ArmsAdjusting T-Arm Width Adjusting T-Arm Depth Adjusting the T-Arms- Adjusting T-Arm WidthAdjusting T-Arm Sockets Adjusting the T-Arms- Adjusting T-Arm DepthAdjusting the Transfer Assists and/or Side Guards Adjusting the T-Arms- Adjusting T-Arm SocketsAdjusting the Transfer Assists and/or Side Guards Replacing the T-Arm Locking LeverUsing/Installing/Adjusting Cantilever Arms Using Catilever ArmsInstalling/Removing/Adjusting Catilever Arms Using/Installing/Adjusting Cantilever ArmsAngled Portion Locking Mechanism Adjustment Replacing and Adjusting Arm Pad Depth for Cantilever ArmsReplacement Seat and Back Replacing the Locking Mechanism in the Back CaneInstalling Fixed Height Stroller Handles Installing Adjustable Angle Stroller HandlesRemoving Adjustable Angle Stroller Handles Adjusting Adjustable Angle Stroller HandlesRemoving/Installing the Spreader Bar Adjusting Adjustable Angle Stroller HandlesRemoving/Installing the Spreader Bar Folding/Unfolding the Back CanesInstalling RemovingReplacing/Installing Front Caster Assemblies Front CastersReplacing Front Fork Replacing Front ForkAdjusting Caster Headtubes Adjusting Caster HeadtubesQuick-Release Axles Removing/Installing Rear WheelsRear Wheels Permanent AxlesAdjusting the Quick-Release Axle Removing/Installing Rear WheelsNon-Projection Handrims Installing Non-Projection HandrimsReplacing Handrims Projection HandrimsInstalling Projection Handrims Removing Projection HandrimsUsing Foot Activated Wheel Locks Foot Activated Wheel Lock ProceduresInstalling/Removing Foot Activated Wheel Locks ANTI-TIPPERS/WHEEL LocksHand Activated Wheel Lock Procedures Installing/Removing Hand Activated Wheel LocksAdjusting the Wheel Lock Engaging/Disengaging Hand Activated Wheel LocksInstalling Anti-Tippers Adjusting the Wheel LockAdjusting Anti-Tippers Adjusting Anti-TippersRecliner Engaging Tilt-In-SpaceRecliner Operating Recliner Engaging Tilt-In-SpaceAdjusting Limit Stops of the Tilt Mechanism Adjusting Anterior Forward Limit StopsReplacing the Back Upholstery Adjusting Posterior Rearward Limit StopsReplacing Upholstery Recliner Models Only Replacing the Headrest UpholsteryAdjusting the Back Height Recliner Models Only Replacing Upholstery Recliner Models OnlyTransport Ready Option About Transport Ready Packages SpecificationsWeight Limit Compliance InformationSecuring the Wheelchair to the Vehicle Positioning the Wheelchair in the VehicleSecurement Points Securing the WheelchairVehicle-Anchored Belts Securing the OccupantSeating System Positioning Belts Positioning BeltsUsing the Ventilator Tray OptionsLimited Warranty USA