Emerson Complete Guide for 5081 Equipment: Instruction Manual and Navigation
Page 47

Model 5081FG

Instruction Manual

IB-106-5081, Rev. 1.0 May 2005

d.Navigation

The IRC in Figure 3-6is used to interact with the Model 5081 Transmitter and navi- gate through the screens on the LCD.

1.Hold the IRC within 6 ft (1.8 m) of the Model 5081 Transmitter and within 15 degrees from the centerline of the transmitter LCD. The amount of ambi- ent light may also affect IRC performance.

NOTE

The LCD may react slowly to IRC commands. Allow sufficient time be- tween key presses to avoid undesired or repeated commands from accumu- lating in the command queue.

2.Use the keys on the IRC to navigate through the menu screens. Refer to Figure 3-6.General usage is as follows:

(a)RESET. Returns to the PROCESS DISPLAY screen at the top of the menu tree. Any non-entered num- ber in the exited state will be ig- nored, and the previous data will be used.

(b)HOLD. Not used.

(c)Left/Right Arrow. Moves left and right among editable digits on the display.

(h)ENTER. Initiates the editing proc- ess and causes the most signifi- cant digit of the edited item to start flashing. Also processes the entry so the previous value updates to the new value entered using the ar- row keys. Failure to press ENTER before exiting a screen will cancel the input value and revert to the previous value.

3

(i)NEXT. Accesses the next user screen as shown in the menu tree. Any non-entered number in the ex- ited state will be ignored, and the previous data will be used.

(j)EXIT. Exits from sub-branches of the menu tree where an exit option is explicitly shown. Otherwise, re- turns to the PROCESS DISPLAY screen at the top of the menu tree. Any non-entered number in the ex- ited state will be ignored, and the previous data will be used.

 

RESET

 

HOLD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAL

 

ENTER

 

 

 

(d)Up/Down Arrow. Increases or de- creases the value of the currently selected digit on the display.

(e)CAL. Accesses the CALCHECK MENU branch of the menu tree. Only works from the PROCESS DISPLAY screen.

(f)PROG. Accesses the PROGRAM MENU branch of the menu tree. Only works from the PROCESS DISPLAY screen.

(g)DIAG. Accesses the DIAGNOS- TICS MENU branch of the menu tree. Only works from the PROC- ESS DISPLAY screen.

PROG

 

NEXT

 

 

 

 

 

 

DIAG

 

EXIT

 

 

 

MODEL 5081

REMOTE CONTROL

ROSEMOUNT

FISHER-ROSEMOUNT

37240005

Figure 3-6. Infrared Remote Control (IRC)

Rosemount Analytical Inc. A Division of Emerson Process Management

Startup and Operation 3-5

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Model 5081FG Essential Instructions Summary Highlights of ChangesEffective May, 2005 Rev Page Model 5081FG Table of ContentsList of Illustrations List of Tables Model 5081FG Definitions PrefaceModel 5081FG Belangrijk Vigtigt Model 5081FG Tärkeää Model 5081FG Wichtig Importante Viktig Model 5081FG Model 5081FG Viktigt Model 5081FG Component Checklist of Typical System Package Contents Section Description and SpecificationsCode Mounting Adapter Stack Side Product MatrixSystem Description System ConfigurationSystem Overview ScopeSystem Features Handling the Analyzer System Considerations Transmitter Typical System InstallationProbe SpecificationsOperating Load Region Lift OFF Maximum Power Supply VoltageOhms VDCInspect Section InstallationPRE-INSTALLATION Mechanical InstallationSide View Bottom View Front ViewMetal Wall Masonry Wall Stack or Duct Horizontal Probe Installation Adjusting Probe Insertion Depth Model 5081FG Installing Model 5081 Transmitter Mounting Holes Cover LockCircuit Terminal END Block TBElectrical Installation Display Positioning AssemblyThermocouple CELL-WH CELL+BK Model 5081 Transmitter 4-20 mA and Signal ConnectionsTerminal Block Conduit Calibration Check Gas Pneumatic InstallationReference Air Package Instrument Air Reference AirFlow SET MAX Point Knob Mounting Holes Outlet ConnectionOutlet Inlet ConnectionGeneral Power UPSection Startup and Operation Proper Calibration Check Gas Flow Rate Reestablishing Proper Calibration Check GAS Flow RateMenu Tree OperationOverview DisplayProgram DiagnosticsCalcheck MenuNavigation Infrared Remote Control IRCO2 Concentration O2 Concentration Analyzer Access Code Or SecurityAnalyzer Access Code Program MenuCell T HI O2 Concentration Indicator Fault ValueO2 Concentration Upper Cell Temperature Fault Value Upper Range VALSET O2 Filter Time Reset MAX Cell TTo Reset Maximum Cell Temperature O2 Concentration Analyzer Access CodeConcentration SET HI Bottle O2SET LO Bottle O2 Model 5081 Transmitter Parameters SET Code Parameter Range DefaultModel 5081 Transmitter Parameters C mV Diagnostics MenuShow Fault 24. Previous Slope Previous Constant 23. Cell ImpedanceCalcheck Menu Accept LOW O2 27. in MANUAL?29. Accept LOW O2 Slope Model 5081FG Connections Hart Communicator Signal LineSection HART/AMS OverviewAnalog Output Device Method 2, For Load Resistance 250 OhmsMenu Tree for Hart Communicator TWO-WIRE in Situ Oxygen AnalyzerHart Communicator PC OFF-LINE and ON-LINE OperationsDevice Setup From Sheet Basic Setup Detailed From Sheet Signal Condition Detailed Setup Output Hart Communicator Start CAL- Check Method Model 5081FG Spare Board Stack Replacement Section Maintenance and ServiceModel 5081 Electronics Replacement Display Board ReplacementRibbon Cable Analog Board CPU Two-Wire In Situ Oxygen Analyzer Exploded ViewOxygen Probe Replacement Oxygen Probe Terminal Block IMPEDANCE, Ω Section TroubleshootingProbe Life Normal Operational ConditionsSpeed Fault IndicationsOfresponse Thermocouple Identifying and Correcting Fault IndicationsFault 1, Open Thermocouple Fault 3, Shorted Thermocouple Fault 5, O2 Cell Open Fault 6, Cell Impedance Too High Fault 5, O2 Cell Open11. Fault 7, Reversed O2 Cell Fault 7, Reversed O2 CellModel 5081FG Section Return of Material Model 5081FG Index No Part Number Description Replacement PartsReplacement Parts List SectionModel 5081FG Section Index Model 5081FG Model 5081FG Page Warranty Two-Wire In Situ Oxygen Analyzer Serial no Order no

5081FG specifications

The Emerson 5081FG Series is a cutting-edge digital smart transmitter designed for various industrial applications, including oil and gas, chemical processing, and water treatment. Known for its accuracy and reliability, the Emerson 5081FG integrates an array of advanced technologies to enhance measurement capabilities and operational efficiency.

One of the main features of the 5081FG is its multi-variable measurement, which allows for the integration of differential pressure, static pressure, and temperature readings into a single device. This capability significantly reduces the need for multiple instruments, leading to lower installation costs and improved data collection efficiency.

With Smart Wireless technology, the Emerson 5081FG offers robust wireless communication, making it ideal for remote or hard-to-reach locations. Its ability to transmit real-time data wirelessly enhances operational awareness and enables proactive maintenance decisions. The transmitter can easily connect to various process control systems for seamless integration and data sharing.

The 5081FG also incorporates Emerson's advanced diagnostics and predictive maintenance algorithms. These features continuously monitor the health of the transmitter and the processes it measures, alerting operators to potential issues before they escalate into serious problems. This proactive approach to maintenance not only improves safety but also minimizes downtime and maximizes productivity.

Another significant characteristic of the Emerson 5081FG is its rugged design, built to withstand harsh industrial environments. With an IP67 rating, it is resistant to dust and water ingress, ensuring reliable operation even in challenging conditions. The device is also designed to handle a wide range of temperatures and pressures, making it versatile for diverse applications.

User-friendly configuration and programming are facilitated by Emerson's intuitive software tools, which provide easy setup and calibration processes. This simplicity allows operators to optimize performance without needing extensive training or support.

In conclusion, the Emerson 5081FG is a powerful and reliable smart transmitter that addresses the needs of various industries. Its multi-variable measurement capability, wireless communication, advanced diagnostics, and rugged design make it an excellent choice for companies looking to enhance their operational efficiency and maintain high standards of safety and reliability. With the Emerson 5081FG, businesses can expect not only accurate measurements but also valuable insights that contribute to smarter decision-making.
Top Page Image Contents