Invacare 1106628 manual INSTALLING/REMOVING Swingaway Footrest Figure, Front Friggings, Removing

Page 20

FRONT FRIGGINGS

PROCEDURE 4

FRONT RIGGINGS

 

 

This Procedure Includes the Following:

Installing/Removing Swingaway Footrest

Adjusting Swingaway Footrest Height

Adjusting Adjustable Angle Flip-up Footplates

Composite/Articulating Footplate Heel Loop Replacement

Installing/Removing Elevating Legrest/Calfpad Assembly

Adjusting the Elevating Legrest/Calfpad Assembly

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure all attach- ing hardware is tightened securely - otherwise injury or damage may occur.

INSTALLING/REMOVING SWINGAWAY FOOTREST (FIGURE 1)

INSTALLING

Footrest Release Lever

1.

Turn the footrest to the side (open

Mounting Tube

Mounting Pin

 

footplate is perpendicular to the wheel-

 

 

Wheelchair

Footrest

 

chair).

2.

Insert the footrest assembly mounting pin

Frame

Assembly

 

 

 

into the mounting tube of the wheelchair

 

 

 

frame.

 

 

3.

Rotate the footrest towards the inside of

 

Footplate

 

 

 

the wheelchair until it locks into place.

 

 

NOTE: The footplate will be on the inside of the

 

 

wheelchair when locked in place.

 

 

4.

Repeat STEPS 1-3 for the other footrest

NOTE: Only 60°

 

 

assembly.

Front Rigging shown for clarity.

5.

If necessary, adjust the footrest height.

Others will attach the same way.

FIGURE 1 - INSTALLING/

 

Refer to ADJUSTING SWINGAWAY

 

FOOTREST HEIGHT in this procedure of

REMOVING SWINGAWAY

 

the manual.

 

FOOTREST

REMOVING

1.Push the footrest release lever inward while rotating the footrest outward.

2.Lift the footrest assembly out of the mounting pin of the wheelchair frame.

3.Repeat STEPS 1-2 for opposite side, if necessary.

Solara jr.™

20

Part No. 1106628

Image 20
Contents Solara jr Solara jr Table of Contents Procedure 8 Wheel LOCKS/ANTI-TIPPERS Special Notes Special NotesLabel Locations Label LocationsInvacare Solara JR SpecificationsSpecifications Procedure General Guidelines Information for Healthcare PROFESSIONALS/ AssistantsGeneral Guidelines Anterior Forward TiltStability Warning Stability ALL ModelsStability ALL Models Except Recliners General Warnings Stability Recliner Models onlyOperating Information Weight Training Weight LimitationCoping with Everyday Obstacles SAFETY/HANDLING of WheelchairsStability and Balance Percentage of Weight Distribution Unoccupied OccupiedStep Tube TippingMethod 1 Wheelchair with Step Tubes Stairways Tipping Curbs Method 2 Wheelchair Without Step TubeESCALATORS? Sorry Transferring to and from Other SeatsSafety Inspection Checklist Safety InspectionTroubleshooting MaintenanceProcedure 2SAFETY Inspection Maintenance Safety PrecautionsTransporting Transporting ProcedureTransporting the Invacare Solara JR INSTALLING/REMOVING Swingaway Footrest Figure Procedure Front RiggingsFront Friggings RemovingAdjusting Swingaway Footrest Height Front Riggings ProcedureHeight Adjustment Ranges Front RiggingsAdjusting Adjustable Angle FLIP-UP Footplates Figure Front Riggingsprocedure Composite Footplate DisassemblyReassembly Articulating Footplate Heel Loop ReplacementAdjusting the Elevating LEGREST/CALFPAD Assembly Figure Adjusting the LegrestAdjusting the Calfpad CalfpadUSING/ADJUSTING Dual Point Arms Figure ARMS/POSITIONING StrapsReplacing Dual Point ARM Clothing Guards Figure Procedure ARMS/POSITIONING StrapsReplacing Dual Point ARM PAD Figure INSTALLING/ADJUSTING USING/INSTALLING/ADJUSTING Cantilever ArmsUsing Figure ARM PAD Replacement for Cantilever Arms Figure INSTALLING/REMOVING T-ARMS Figure Adjusting the T-ARMSInstalling T-ARMS Adjusting T-ARM Height FigureDepth Inside T-Arm Post Arm Release Lever Locked PositionOutside T- Arm Post SocketAdjusting T-ARM Transfer Assists AND/OR Side Guards Figure Adjusting T-ARM Sockets FigureHex screws and washers are removed Arm Arm Clamp Slot Arm SocketINSTALLING/REPLACING Seat Positioning Straps Figure ReplacingSide Guard Transfer Assist Socket ScrewsINSTALLING/REPLACING Chest Positioning Straps Figure Back Cane Locknut Hex Screw Chest Positioning StrapBACK/SEAT FOLDING/UNFOLDING Back Assembly FigureINSTALLING/REMOVING Stroller Handles Figure Installing Figure Detail a QUICK-RELEASE PIN InstalledRemoving Figure Quick-Release Pin Or bolt and locknut Recliners onlyStroller Handle Thumbscrew Release Lever Procedure BACK/SEAT Adjusting FigureLocked Position Using the Telescoping Back Canes Figure RAISING/LOWERINGStoring OpenINSTALLING/REPLACING the Back Upholstery Fixed Back Canes FigureClamp Spreader Bar Set Screw Back Canes Installing and Removing a Seating SystemREMOVING/INSTALLING the Spreader BAR Figure Wheelchair Front Installing the Seat Cushion FigureRear REMOVING/INSTALLING Rear Wheels Figure WHEELS/FORKS ProcedureWHEELS/FORKS Quick Release AxleAdjusting the Quick Release Axle Figure SEAT-TO-FLOOR Height AdjustmentProcedure WHEELS/FORKS Axle Mounting Plate Locking PinsAdjusting Forks Figure Fork Dust Cover Caster HeadtubeAdjusting Wheel Locks Figures 1 Procedure Wheel LOCKS/ANTI-TIPPERSWheel TIPPERS-LOCKS/ANTI 16-INCH Rear Wheels 18 24-INCH Rear WheelsWheel LOCKS/ANTI-TIPPERS Using the Wheel LocksFoot Activated Wheel Locks 12-INCH Wheels only Figure INSTALLING/ADJUSTING ANTI-TIPPERS Figure Adjusting2 to 2-inch ClearanceAnti-tipper Ground/FloorTILT/RECLINE TILT/RECLINE ProcedureEngaging Tilt in SPACE/RECLINER Operation Procedure TILT/RECLINE Engaging TILT-IN-SPACE FigureTILT-IN-SPACE Tilt SlideTILT/RECLINE Procedure Recliner Operation Figure Gas CylinderAdjusting Tilt Trigger Release Cables Figure Cable Locking Nut Trigger Release Lever Cable Adjusting NutAdjusting Upper Tilt Locking Collar Figure Bearing HousingPositioning Tilt Locking Collars Magnetic protractor reads desired angle of tiltReplacing the Back Upholstery Replacing the Headrest UpholsteryHeadrest Upholstery Extension Back Cane Back UpholsteryAdjusting the Back Height Recliner Models only Figure Inch Seat Cushion PositionContracture Assembly Angle Adjustment Figure Procedure Contracture FootplateFootplatecontracture Mounting ScrewUsing the Optional Quick Release PIN Figure Angle Adjustment of the Contracture Footplate FigureContracture Footplate Depth Adjustment Figure ContractureContracture Footplate Height Adjustment Figure Replacing the Contracture Footplate Heel Loop FigureMounting Hole ContractureSolara jr Solara jr Warranty Limited WarrantyWarranty One Invacare Way

1106628 specifications

The Invacare 1106628 is a robust and innovative mobility solution designed to enhance the quality of life for individuals with limited mobility. This power wheelchair combines advanced technology and user-friendly features, making it an excellent choice for both indoor and outdoor use.

One of the standout characteristics of the Invacare 1106628 is its versatile seating system, which provides optimal comfort and support. The seat is designed to accommodate various body types and can be adjusted to ensure perfect alignment and positioning. Additionally, the chair includes a contoured backrest that offers lumbar support, promoting good posture during extended use.

Technology plays a significant role in the design of the Invacare 1106628. The wheelchair is equipped with a powerful motor and a durable battery system, allowing for a long driving range and reliable performance. With a top speed that makes navigating urban settings easy, users can enjoy both independence and accessibility. The advanced joystick control allows for smooth and precise maneuvering, enabling efficient navigation through tight spaces.

The wheelchair also boasts a sturdy construction, ensuring it can withstand the rigors of daily use. The frame is made from high-quality materials, providing durability while remaining lightweight enough for easy transport. Its compact design enhances maneuverability, making it suitable for use in various environments, from bustling shopping malls to narrow hallways in homes.

Safety features are paramount in the design of the Invacare 1106628. The wheelchair comes with anti-tip wheels, ensuring stability during movement, particularly when climbing slopes or navigating uneven terrain. The durable tires are designed for excellent traction, further enhancing safety and control in various outdoor settings.

In terms of additional features, the Invacare 1106628 includes customizable options such as adjustable armrests, footrests, and various accessory attachments. This flexibility allows users to tailor the wheelchair to their specific needs, enhancing overall comfort and usability.

In conclusion, the Invacare 1106628 is a well-engineered power wheelchair that incorporates advanced technology, safety features, and customizable options. It is designed to provide individuals with mobility challenges the independence and support they need, making it a valuable asset for users seeking to improve their quality of life. Whether navigating through their home or enjoying the great outdoors, the Invacare 1106628 delivers on performance, comfort, and durability.