Invacare 1106628 manual Adjusting Swingaway Footrest Height, Front Riggings Procedure

Page 21

FRONT RIGGINGS

PROCEDURE 4

 

 

ADJUSTING SWINGAWAY FOOTREST HEIGHT

HEIGHT ADJUSTMENT RANGES:

60°

13-17-inches

70°

13-17-inches

90°

5-8-inches

90°

5-11-inches (with 3-inch extension)

NOTE: If using ANY type of extension with the AD- JUSTABLE FLIP-UP FOOTPLATE, refer to ADJUST-

ING ADJUSTABLE ANGLE FLIP-UP FOOTPLATES - PERPENDICULAR AND/OR INVERSION/EVERSION ADJUSTMENT in this procedure of the manual.

60°, 70° and 70° TAPER (FIGURE 2)

1.Remove the footrest from the wheelchair. Refer to INSTALLING/REMOVING SWINGAWAY FOOTREST in this proce- dure of the manual.

 

Footrest Upper

Hex Screw

Support

Coved

SpacerMounting

Tube

Footplate

FIGURE 2 - ADJUSTING

SWINGAWAY FOOTREST HEIGHT - 60° , 70° AND 70°

TAPER

FRONT RIGGINGS

2.Remove the hex screw and coved spacer and slide the footrest up or down on its mounting tube until the desired footrest height is achieved.

3.Reassemble the hex screw and coved spacer through the footrest upper support and mounting tube as shown in FIGURE 2.

4.Securely tighten the hex screw and coved spacer.

5.Install the footrest assembly onto the wheelchair. Refer to INSTALLING/REMOVING SWINGAWAY FOOTREST in this procedure of the manual.

6.Repeat STEPS 1-5 for the opposite side of the wheelchair, if necessary.

90° AND 70° MFX (FIGURE 3)

1.Remove the footrest from the wheelchair. Refer to INSTALLING/REMOVING SWINGAWAY FOOTREST in this procedure of the manual.

2.Remove the socket screw, washers, coved spacer and locknut that secures the footplate hinge to the footrest support.

3.Slide the footrest support to the desired position.

4.Secure the footrest support to the footplate hinge. Refer to FIGURE 3 for correct hardware orientation.

5.Securely tighten the socket screw, wash- ers, coved spacer and locknut.

6.Install the footrest assembly onto the wheelchair. Refer to INSTALLING/ REMOVING SWINGAWAY FOOTREST in this procedure of the manual.

Footplate Hinge

Socket Screw

Locknut

Washers

 

 

Footrest Support

Coved Spacer

Height Adjustment

Holes

3-inch

Locknut Extension

Hex Screw

FIGURE 3 - ADJUSTING SWINGAWAY FOOTREST HEIGHT - 90° AND 70° MFX

7. Repeat STEPS 1-6 for the opposite side of the wheelchair, if necessary.

Part No. 1106628

21

Solara jr.™

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Solara jr Solara jr Table of Contents Procedure 8 Wheel LOCKS/ANTI-TIPPERS Special Notes Special NotesLabel Locations Label LocationsSpecifications SpecificationsInvacare Solara JR Information for Healthcare PROFESSIONALS/ Assistants Procedure General GuidelinesGeneral Guidelines Anterior Forward TiltStability ALL Models Stability ALL Models Except ReclinersStability Warning Stability Recliner Models only Operating InformationGeneral Warnings Weight Limitation Weight TrainingSAFETY/HANDLING of Wheelchairs Stability and BalanceCoping with Everyday Obstacles Unoccupied Occupied Percentage of Weight DistributionTipping Method 1 Wheelchair with Step TubesStep Tube Tipping Curbs Method 2 Wheelchair Without Step Tube StairwaysTransferring to and from Other Seats ESCALATORS? SorrySafety Inspection Safety Inspection ChecklistMaintenance TroubleshootingProcedure 2SAFETY Inspection Maintenance Safety PrecautionsTransporting Procedure Transporting the Invacare Solara JRTransporting Procedure Front Riggings INSTALLING/REMOVING Swingaway Footrest FigureFront Friggings RemovingFront Riggings Procedure Adjusting Swingaway Footrest HeightHeight Adjustment Ranges Front RiggingsAdjusting Adjustable Angle FLIP-UP Footplates Figure Composite Footplate Disassembly Front RiggingsprocedureReassembly Articulating Footplate Heel Loop ReplacementAdjusting the Legrest Adjusting the Elevating LEGREST/CALFPAD Assembly FigureAdjusting the Calfpad CalfpadARMS/POSITIONING Straps USING/ADJUSTING Dual Point Arms FigureProcedure ARMS/POSITIONING Straps Replacing Dual Point ARM PAD FigureReplacing Dual Point ARM Clothing Guards Figure USING/INSTALLING/ADJUSTING Cantilever Arms Using FigureINSTALLING/ADJUSTING ARM PAD Replacement for Cantilever Arms Figure Adjusting the T-ARMS INSTALLING/REMOVING T-ARMS FigureInstalling T-ARMS Adjusting T-ARM Height FigureInside T-Arm Post Arm Release Lever Locked Position DepthOutside T- Arm Post SocketAdjusting T-ARM Sockets Figure Adjusting T-ARM Transfer Assists AND/OR Side Guards FigureHex screws and washers are removed Arm Arm Clamp Slot Arm SocketReplacing INSTALLING/REPLACING Seat Positioning Straps FigureSide Guard Transfer Assist Socket ScrewsBack Cane Locknut Hex Screw Chest Positioning Strap INSTALLING/REPLACING Chest Positioning Straps FigureFOLDING/UNFOLDING Back Assembly Figure INSTALLING/REMOVING Stroller Handles FigureBACK/SEAT Detail a QUICK-RELEASE PIN Installed Installing FigureRemoving Figure Quick-Release Pin Or bolt and locknut Recliners onlyProcedure BACK/SEAT Adjusting Figure Locked PositionStroller Handle Thumbscrew Release Lever RAISING/LOWERING Using the Telescoping Back Canes FigureStoring OpenFixed Back Canes Figure INSTALLING/REPLACING the Back UpholsteryInstalling and Removing a Seating System REMOVING/INSTALLING the Spreader BAR FigureClamp Spreader Bar Set Screw Back Canes Installing the Seat Cushion Figure RearWheelchair Front WHEELS/FORKS Procedure REMOVING/INSTALLING Rear Wheels FigureWHEELS/FORKS Quick Release AxleSEAT-TO-FLOOR Height Adjustment Adjusting the Quick Release Axle FigureProcedure WHEELS/FORKS Axle Mounting Plate Locking PinsFork Dust Cover Caster Headtube Adjusting Forks FigureProcedure Wheel LOCKS/ANTI-TIPPERS Adjusting Wheel Locks Figures 1Wheel TIPPERS-LOCKS/ANTI 16-INCH Rear Wheels 18 24-INCH Rear WheelsUsing the Wheel Locks Foot Activated Wheel Locks 12-INCH Wheels only FigureWheel LOCKS/ANTI-TIPPERS Adjusting INSTALLING/ADJUSTING ANTI-TIPPERS Figure2 to 2-inch ClearanceAnti-tipper Ground/FloorTILT/RECLINE Procedure Engaging Tilt in SPACE/RECLINER OperationTILT/RECLINE Engaging TILT-IN-SPACE Figure Procedure TILT/RECLINETILT-IN-SPACE Tilt SlideGas Cylinder TILT/RECLINE Procedure Recliner Operation FigureCable Locking Nut Trigger Release Lever Cable Adjusting Nut Adjusting Tilt Trigger Release Cables FigureBearing Housing Adjusting Upper Tilt Locking Collar FigurePositioning Tilt Locking Collars Magnetic protractor reads desired angle of tiltReplacing the Headrest Upholstery Replacing the Back UpholsteryHeadrest Upholstery Extension Back Cane Back UpholsteryInch Seat Cushion Position Adjusting the Back Height Recliner Models only FigureProcedure Contracture Footplate Contracture Assembly Angle Adjustment FigureFootplatecontracture Mounting ScrewAngle Adjustment of the Contracture Footplate Figure Using the Optional Quick Release PIN FigureContracture Footplate Depth Adjustment Figure ContractureReplacing the Contracture Footplate Heel Loop Figure Contracture Footplate Height Adjustment FigureMounting Hole ContractureSolara jr Solara jr Limited Warranty WarrantyWarranty One Invacare Way

1106628 specifications

The Invacare 1106628 is a robust and innovative mobility solution designed to enhance the quality of life for individuals with limited mobility. This power wheelchair combines advanced technology and user-friendly features, making it an excellent choice for both indoor and outdoor use.

One of the standout characteristics of the Invacare 1106628 is its versatile seating system, which provides optimal comfort and support. The seat is designed to accommodate various body types and can be adjusted to ensure perfect alignment and positioning. Additionally, the chair includes a contoured backrest that offers lumbar support, promoting good posture during extended use.

Technology plays a significant role in the design of the Invacare 1106628. The wheelchair is equipped with a powerful motor and a durable battery system, allowing for a long driving range and reliable performance. With a top speed that makes navigating urban settings easy, users can enjoy both independence and accessibility. The advanced joystick control allows for smooth and precise maneuvering, enabling efficient navigation through tight spaces.

The wheelchair also boasts a sturdy construction, ensuring it can withstand the rigors of daily use. The frame is made from high-quality materials, providing durability while remaining lightweight enough for easy transport. Its compact design enhances maneuverability, making it suitable for use in various environments, from bustling shopping malls to narrow hallways in homes.

Safety features are paramount in the design of the Invacare 1106628. The wheelchair comes with anti-tip wheels, ensuring stability during movement, particularly when climbing slopes or navigating uneven terrain. The durable tires are designed for excellent traction, further enhancing safety and control in various outdoor settings.

In terms of additional features, the Invacare 1106628 includes customizable options such as adjustable armrests, footrests, and various accessory attachments. This flexibility allows users to tailor the wheelchair to their specific needs, enhancing overall comfort and usability.

In conclusion, the Invacare 1106628 is a well-engineered power wheelchair that incorporates advanced technology, safety features, and customizable options. It is designed to provide individuals with mobility challenges the independence and support they need, making it a valuable asset for users seeking to improve their quality of life. Whether navigating through their home or enjoying the great outdoors, the Invacare 1106628 delivers on performance, comfort, and durability.
Top Page Image Contents