Invacare 1106628 manual Adjusting Tilt Trigger Release Cables Figure

Page 50

TILT/RECLINE

PROCEDURE 9

TILT/RECLINE

 

 

ADJUSTING TILT TRIGGER RELEASE CABLES (FIGURE 3)

NOTE: This procedure applies to tilt-in-space release cables ONLY.

WARNING

DO NOT adjust the trigger release cables while the cables are coiled up. The adjust- ment will be too tight when the cable is straightened and the tilt mechanism will not lock and hold its position, possibly causing injury.

1.To adjust the LEFT tilt mechanism:

Squeeze the trigger release lever of the RIGHT cable assembly and try to tilt the wheel- chair. The wheelchair should not tilt.

2.If the LEFT side of the wheelchair tilts without squeezing the trigger release lever of the LEFT cable assembly, perform the following steps:

A.Loosen the cable locking nut that secures the cable adjusting nut in place.

B.Turn cable adjusting nut one (1) of two (2) ways:

NOTE: If the cable is too loose, the tilt mechanism will not work.

WARNING

DO NOT over tighten the cable adjusting nut on the cable. Over tightening the cable adjusting nut on the cable WILL unlock the tilt mechanism, possibly causing injury.

•TO TIGHTEN - Turn the cable adjusting nut CLOCKWISE. DO NOT over- tighten the cable adjusting nut. Refer to FIGURE 2.

•TO LOOSEN - Turn the cable adjusting nut COUNTERCLOCKWISE. Refer to FIGURE 2.

C.While holding the cable adjusting nut in place, tighten the cable locking nut against the cable adjusting nut.

D.Repeat STEP 1.

E.Repeat STEP 2 until the LEFT side of the wheelchair DOES NOT tilt.

3.To adjust the RIGHT tilt mechanism:

Repeat STEPS 1 and 2 for the LEFT trigger release lever.

Cable Locking Nut

Trigger Release

Lever

Cable Adjusting Nut

Cable Assembly

 

FIGURE 3 - ADJUSTING TRIGGER RELEASE CABLES

Solara jr.™

50

Part No. 1106628

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Solara jr Solara jr Table of Contents Procedure 8 Wheel LOCKS/ANTI-TIPPERS Special Notes Special NotesLabel Locations Label LocationsInvacare Solara JR SpecificationsSpecifications General Guidelines Procedure General GuidelinesInformation for Healthcare PROFESSIONALS/ Assistants Anterior Forward TiltStability Warning Stability ALL ModelsStability ALL Models Except Recliners General Warnings Stability Recliner Models onlyOperating Information Weight Training Weight LimitationCoping with Everyday Obstacles SAFETY/HANDLING of WheelchairsStability and Balance Percentage of Weight Distribution Unoccupied OccupiedStep Tube TippingMethod 1 Wheelchair with Step Tubes Stairways Tipping Curbs Method 2 Wheelchair Without Step TubeESCALATORS? Sorry Transferring to and from Other SeatsSafety Inspection Checklist Safety InspectionProcedure 2SAFETY Inspection TroubleshootingMaintenance Maintenance Safety PrecautionsTransporting Transporting ProcedureTransporting the Invacare Solara JR Front Friggings INSTALLING/REMOVING Swingaway Footrest FigureProcedure Front Riggings RemovingHeight Adjustment Ranges Adjusting Swingaway Footrest HeightFront Riggings Procedure Front RiggingsAdjusting Adjustable Angle FLIP-UP Footplates Figure Reassembly Articulating Footplate Front RiggingsprocedureComposite Footplate Disassembly Heel Loop ReplacementAdjusting the Calfpad Adjusting the Elevating LEGREST/CALFPAD Assembly FigureAdjusting the Legrest CalfpadUSING/ADJUSTING Dual Point Arms Figure ARMS/POSITIONING StrapsReplacing Dual Point ARM Clothing Guards Figure Procedure ARMS/POSITIONING StrapsReplacing Dual Point ARM PAD Figure INSTALLING/ADJUSTING USING/INSTALLING/ADJUSTING Cantilever ArmsUsing Figure ARM PAD Replacement for Cantilever Arms Figure Installing T-ARMS INSTALLING/REMOVING T-ARMS FigureAdjusting the T-ARMS Adjusting T-ARM Height FigureOutside T- Arm Post DepthInside T-Arm Post Arm Release Lever Locked Position SocketHex screws and washers are removed Arm Arm Clamp Adjusting T-ARM Transfer Assists AND/OR Side Guards FigureAdjusting T-ARM Sockets Figure Slot Arm SocketSide Guard INSTALLING/REPLACING Seat Positioning Straps FigureReplacing Transfer Assist Socket ScrewsINSTALLING/REPLACING Chest Positioning Straps Figure Back Cane Locknut Hex Screw Chest Positioning StrapBACK/SEAT FOLDING/UNFOLDING Back Assembly FigureINSTALLING/REMOVING Stroller Handles Figure Removing Figure Installing FigureDetail a QUICK-RELEASE PIN Installed Quick-Release Pin Or bolt and locknut Recliners onlyStroller Handle Thumbscrew Release Lever Procedure BACK/SEAT Adjusting FigureLocked Position Storing Using the Telescoping Back Canes FigureRAISING/LOWERING OpenINSTALLING/REPLACING the Back Upholstery Fixed Back Canes FigureClamp Spreader Bar Set Screw Back Canes Installing and Removing a Seating SystemREMOVING/INSTALLING the Spreader BAR Figure Wheelchair Front Installing the Seat Cushion FigureRear WHEELS/FORKS REMOVING/INSTALLING Rear Wheels FigureWHEELS/FORKS Procedure Quick Release AxleProcedure WHEELS/FORKS Adjusting the Quick Release Axle FigureSEAT-TO-FLOOR Height Adjustment Axle Mounting Plate Locking PinsAdjusting Forks Figure Fork Dust Cover Caster HeadtubeWheel TIPPERS-LOCKS/ANTI Adjusting Wheel Locks Figures 1Procedure Wheel LOCKS/ANTI-TIPPERS 16-INCH Rear Wheels 18 24-INCH Rear WheelsWheel LOCKS/ANTI-TIPPERS Using the Wheel LocksFoot Activated Wheel Locks 12-INCH Wheels only Figure 2 to 2-inch ClearanceAnti-tipper INSTALLING/ADJUSTING ANTI-TIPPERS FigureAdjusting Ground/FloorTILT/RECLINE TILT/RECLINE ProcedureEngaging Tilt in SPACE/RECLINER Operation TILT-IN-SPACE Procedure TILT/RECLINEEngaging TILT-IN-SPACE Figure Tilt SlideTILT/RECLINE Procedure Recliner Operation Figure Gas CylinderAdjusting Tilt Trigger Release Cables Figure Cable Locking Nut Trigger Release Lever Cable Adjusting NutPositioning Tilt Locking Collars Adjusting Upper Tilt Locking Collar FigureBearing Housing Magnetic protractor reads desired angle of tiltHeadrest Upholstery Extension Back Cane Replacing the Back UpholsteryReplacing the Headrest Upholstery Back UpholsteryAdjusting the Back Height Recliner Models only Figure Inch Seat Cushion PositionFootplatecontracture Contracture Assembly Angle Adjustment FigureProcedure Contracture Footplate Mounting ScrewContracture Footplate Depth Adjustment Figure Using the Optional Quick Release PIN FigureAngle Adjustment of the Contracture Footplate Figure ContractureMounting Hole Contracture Footplate Height Adjustment FigureReplacing the Contracture Footplate Heel Loop Figure ContractureSolara jr Solara jr Warranty Limited WarrantyWarranty One Invacare Way

1106628 specifications

The Invacare 1106628 is a robust and innovative mobility solution designed to enhance the quality of life for individuals with limited mobility. This power wheelchair combines advanced technology and user-friendly features, making it an excellent choice for both indoor and outdoor use.

One of the standout characteristics of the Invacare 1106628 is its versatile seating system, which provides optimal comfort and support. The seat is designed to accommodate various body types and can be adjusted to ensure perfect alignment and positioning. Additionally, the chair includes a contoured backrest that offers lumbar support, promoting good posture during extended use.

Technology plays a significant role in the design of the Invacare 1106628. The wheelchair is equipped with a powerful motor and a durable battery system, allowing for a long driving range and reliable performance. With a top speed that makes navigating urban settings easy, users can enjoy both independence and accessibility. The advanced joystick control allows for smooth and precise maneuvering, enabling efficient navigation through tight spaces.

The wheelchair also boasts a sturdy construction, ensuring it can withstand the rigors of daily use. The frame is made from high-quality materials, providing durability while remaining lightweight enough for easy transport. Its compact design enhances maneuverability, making it suitable for use in various environments, from bustling shopping malls to narrow hallways in homes.

Safety features are paramount in the design of the Invacare 1106628. The wheelchair comes with anti-tip wheels, ensuring stability during movement, particularly when climbing slopes or navigating uneven terrain. The durable tires are designed for excellent traction, further enhancing safety and control in various outdoor settings.

In terms of additional features, the Invacare 1106628 includes customizable options such as adjustable armrests, footrests, and various accessory attachments. This flexibility allows users to tailor the wheelchair to their specific needs, enhancing overall comfort and usability.

In conclusion, the Invacare 1106628 is a well-engineered power wheelchair that incorporates advanced technology, safety features, and customizable options. It is designed to provide individuals with mobility challenges the independence and support they need, making it a valuable asset for users seeking to improve their quality of life. Whether navigating through their home or enjoying the great outdoors, the Invacare 1106628 delivers on performance, comfort, and durability.
Top Page Image Contents