Invacare 1106628 Front Riggingsprocedure, Composite Footplate Disassembly, Articulating Footplate

Page 23
FIGURE 6 - INSTALLING/
REMOVING ELEVATING LEGREST/
CALFPAD ASSEMBLY
Footplate Assembly
Wheelchair Frame

FRONT RIGGINGSPROCEDURE 4

COMPOSITE/ARTICULATING FOOTPLATE HEEL LOOP

 

REPLACEMENT (FIGURE 5)

COMPOSITE FOOTPLATE

 

DISASSEMBLY

 

Swingaway Footrest Assembly

Composite.

 

Hex Screw and Coved Spacer

1.

Remove the hex screw and coved spacer

Phillips Screw

 

 

that secure the lower footrest assembly

 

 

 

 

to the swing away footrest assembly.

 

Lower Footrest

Phillips

2.

Remove the lower footrest assembly.

 

Screws

Spacer

Assembly

 

3.

Remove the phillips screw and locknut

 

 

 

 

Washer

 

that secure the heel loop to the footrest.

Heel

 

 

 

 

4.

Slide heel loop off of the footrest.

Loop

 

Heel

 

 

 

 

 

 

Articulating.

Locknut

Loop

1.

Remove the phillips screws, washers and

 

Spacer

 

 

spacers that secure the heel loop to the

 

 

 

 

articulating footplate.

 

 

 

REASSEMBLY

ARTICULATING

 

 

FOOTPLATE

 

1.

Replace heel loop.

 

 

 

 

 

2.

Reverse the disassembly procedures.

 

FIGURE 5 - COMPOSITE/

NOTE: When securing the heel loop to the footrest as-

ARTICULATING FOOTPLATE

sembly, tighten phillips screw until the spacer is secure.

HEEL LOOP REPLACEMENT

INSTALLING/REMOVING ELEVATING LEGREST/CALFPAD ASSEMBLY (FIGURE 6)

FRONT RIGGINGS

INSTALLING

1.Insert the footplate assembly into the calfpad assembly and secure it with bolt and nut.

2.Place legrest/calfpad assembly on the outside of the wheelchair and insert legrest mounting pin into the legrest mounting tube on the wheelchair frame.

3.Rotate legrest/calfpad assembly toward the inside of the wheelchair until it locks in place.

NOTE: The calfpad of the legrest will be on the inside of the wheelchair when locked in place.

4.Repeat STEPS 1-3 for the other legrest assembly.

Legrest

Legrest Mounting Pin

Mounting

 

Tube

Calfpad

 

 

Assembly

Bolt and

ReleaseNut

Handle

5.Adjust the footplate to the correct height by loosening the bolt and nut and sliding

the inner tube up or down until desired height is achieved. Securely tighten bolt and nut.

REMOVING

1.Push the legrest release handle inward while rotating the footrest outward.

2.Lift the legrest assembly out of the legrest mounting tube.

Part No. 1106628

23

Solara jr.™

Image 23
Contents Solara jr Solara jr Table of Contents Procedure 8 Wheel LOCKS/ANTI-TIPPERS Special Notes Special NotesLabel Locations Label LocationsInvacare Solara JR SpecificationsSpecifications Anterior Forward Tilt Procedure General GuidelinesInformation for Healthcare PROFESSIONALS/ Assistants General GuidelinesStability Warning Stability ALL ModelsStability ALL Models Except Recliners General Warnings Stability Recliner Models onlyOperating Information Weight Limitation Weight TrainingCoping with Everyday Obstacles SAFETY/HANDLING of WheelchairsStability and Balance Unoccupied Occupied Percentage of Weight DistributionStep Tube TippingMethod 1 Wheelchair with Step Tubes Tipping Curbs Method 2 Wheelchair Without Step Tube StairwaysTransferring to and from Other Seats ESCALATORS? SorrySafety Inspection Safety Inspection ChecklistMaintenance Safety Precautions TroubleshootingMaintenance Procedure 2SAFETY InspectionTransporting Transporting ProcedureTransporting the Invacare Solara JR Removing INSTALLING/REMOVING Swingaway Footrest FigureProcedure Front Riggings Front FriggingsFront Riggings Adjusting Swingaway Footrest HeightFront Riggings Procedure Height Adjustment RangesAdjusting Adjustable Angle FLIP-UP Footplates Figure Heel Loop Replacement Front RiggingsprocedureComposite Footplate Disassembly Reassembly Articulating FootplateCalfpad Adjusting the Elevating LEGREST/CALFPAD Assembly FigureAdjusting the Legrest Adjusting the CalfpadARMS/POSITIONING Straps USING/ADJUSTING Dual Point Arms FigureReplacing Dual Point ARM Clothing Guards Figure Procedure ARMS/POSITIONING StrapsReplacing Dual Point ARM PAD Figure INSTALLING/ADJUSTING USING/INSTALLING/ADJUSTING Cantilever ArmsUsing Figure ARM PAD Replacement for Cantilever Arms Figure Adjusting T-ARM Height Figure INSTALLING/REMOVING T-ARMS FigureAdjusting the T-ARMS Installing T-ARMSSocket DepthInside T-Arm Post Arm Release Lever Locked Position Outside T- Arm PostSlot Arm Socket Adjusting T-ARM Transfer Assists AND/OR Side Guards FigureAdjusting T-ARM Sockets Figure Hex screws and washers are removed Arm Arm ClampTransfer Assist Socket Screws INSTALLING/REPLACING Seat Positioning Straps FigureReplacing Side GuardBack Cane Locknut Hex Screw Chest Positioning Strap INSTALLING/REPLACING Chest Positioning Straps FigureBACK/SEAT FOLDING/UNFOLDING Back Assembly FigureINSTALLING/REMOVING Stroller Handles Figure Quick-Release Pin Or bolt and locknut Recliners only Installing FigureDetail a QUICK-RELEASE PIN Installed Removing FigureStroller Handle Thumbscrew Release Lever Procedure BACK/SEAT Adjusting FigureLocked Position Open Using the Telescoping Back Canes FigureRAISING/LOWERING StoringFixed Back Canes Figure INSTALLING/REPLACING the Back UpholsteryClamp Spreader Bar Set Screw Back Canes Installing and Removing a Seating SystemREMOVING/INSTALLING the Spreader BAR Figure Wheelchair Front Installing the Seat Cushion FigureRear Quick Release Axle REMOVING/INSTALLING Rear Wheels FigureWHEELS/FORKS Procedure WHEELS/FORKSAxle Mounting Plate Locking Pins Adjusting the Quick Release Axle FigureSEAT-TO-FLOOR Height Adjustment Procedure WHEELS/FORKSFork Dust Cover Caster Headtube Adjusting Forks Figure16-INCH Rear Wheels 18 24-INCH Rear Wheels Adjusting Wheel Locks Figures 1Procedure Wheel LOCKS/ANTI-TIPPERS Wheel TIPPERS-LOCKS/ANTIWheel LOCKS/ANTI-TIPPERS Using the Wheel LocksFoot Activated Wheel Locks 12-INCH Wheels only Figure Ground/Floor INSTALLING/ADJUSTING ANTI-TIPPERS FigureAdjusting 2 to 2-inch ClearanceAnti-tipperTILT/RECLINE TILT/RECLINE ProcedureEngaging Tilt in SPACE/RECLINER Operation Tilt Slide Procedure TILT/RECLINEEngaging TILT-IN-SPACE Figure TILT-IN-SPACEGas Cylinder TILT/RECLINE Procedure Recliner Operation FigureCable Locking Nut Trigger Release Lever Cable Adjusting Nut Adjusting Tilt Trigger Release Cables FigureMagnetic protractor reads desired angle of tilt Adjusting Upper Tilt Locking Collar FigureBearing Housing Positioning Tilt Locking CollarsBack Upholstery Replacing the Back UpholsteryReplacing the Headrest Upholstery Headrest Upholstery Extension Back CaneInch Seat Cushion Position Adjusting the Back Height Recliner Models only FigureMounting Screw Contracture Assembly Angle Adjustment FigureProcedure Contracture Footplate FootplatecontractureContracture Using the Optional Quick Release PIN FigureAngle Adjustment of the Contracture Footplate Figure Contracture Footplate Depth Adjustment FigureContracture Contracture Footplate Height Adjustment FigureReplacing the Contracture Footplate Heel Loop Figure Mounting HoleSolara jr Solara jr Warranty Limited WarrantyWarranty One Invacare Way

1106628 specifications

The Invacare 1106628 is a robust and innovative mobility solution designed to enhance the quality of life for individuals with limited mobility. This power wheelchair combines advanced technology and user-friendly features, making it an excellent choice for both indoor and outdoor use.

One of the standout characteristics of the Invacare 1106628 is its versatile seating system, which provides optimal comfort and support. The seat is designed to accommodate various body types and can be adjusted to ensure perfect alignment and positioning. Additionally, the chair includes a contoured backrest that offers lumbar support, promoting good posture during extended use.

Technology plays a significant role in the design of the Invacare 1106628. The wheelchair is equipped with a powerful motor and a durable battery system, allowing for a long driving range and reliable performance. With a top speed that makes navigating urban settings easy, users can enjoy both independence and accessibility. The advanced joystick control allows for smooth and precise maneuvering, enabling efficient navigation through tight spaces.

The wheelchair also boasts a sturdy construction, ensuring it can withstand the rigors of daily use. The frame is made from high-quality materials, providing durability while remaining lightweight enough for easy transport. Its compact design enhances maneuverability, making it suitable for use in various environments, from bustling shopping malls to narrow hallways in homes.

Safety features are paramount in the design of the Invacare 1106628. The wheelchair comes with anti-tip wheels, ensuring stability during movement, particularly when climbing slopes or navigating uneven terrain. The durable tires are designed for excellent traction, further enhancing safety and control in various outdoor settings.

In terms of additional features, the Invacare 1106628 includes customizable options such as adjustable armrests, footrests, and various accessory attachments. This flexibility allows users to tailor the wheelchair to their specific needs, enhancing overall comfort and usability.

In conclusion, the Invacare 1106628 is a well-engineered power wheelchair that incorporates advanced technology, safety features, and customizable options. It is designed to provide individuals with mobility challenges the independence and support they need, making it a valuable asset for users seeking to improve their quality of life. Whether navigating through their home or enjoying the great outdoors, the Invacare 1106628 delivers on performance, comfort, and durability.