Invacare 1106628 REMOVING/INSTALLING Rear Wheels Figure, WHEELS/FORKS Procedure, Wheels/Forks

Page 41

WHEELS/FORKS

PROCEDURE 7

 

 

This Procedure Includes the Following:

Removing/Installing Rear Wheels

Adjusting the Quick-Release Axle

Seat-to-Floor Height Adjustment

Adjusting Forks

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result.

REMOVING/INSTALLING REAR WHEELS (FIGURE 1)

NOTE: To remove rear wheels, reverse this procedure.

WHEELS/FORKS

NOTE: If any adjustments (size or position) to the rear wheels have been made, the anti-tippers must be adjusted to maintain the 1-1/2 to 2-inch clear- ance. If this adjustment cannot be made with the anti-tippers currently installed, a different model may be required. Consult a qualified technician for assistance.

1.Push in the detent pin of the quick release axle and insert the quick release axle through the center of the rear wheel.

2.Push in the tip of the quick-release axle again and insert the axle (with wheel) into the axle mounting plate on the side of the wheelchair frame until the assem- bly locks in place.

Axle Mounting

 

Plate

Wheelchair Frame

Locking

 

Pins

 

Detent

 

Pin

 

Quick Release Axle

Rear Wheel

 

NOTE: Only 12-inch rear wheel is shown. All other wheels will install/remove in the same manner.

FIGURE 1 - REMOVING/

INSTALLING REAR WHEELS

WARNING

Make sure detent pin and locking pins of the quick release axles are fully released BEFORE operating the wheelchair.

The locking pins MUST be protruding past the inside of the axle mounting plate for a positive lock.

Keep locking pins clean.

3.If the locking pins of the quick release axles are not protruding past the inside of the axle mounting plate or there is too much movement of the rear wheel assembly in a back and forth position, refer to ADJUSTING THE QUICK RELEASE AXLE in this procedure of the manual.

4.Repeat STEPS 1-3 for other rear wheel assembly.

5.Adjust the wheel locks. Refer to WHEEL LOCK ADJUSTMENT in PROCEDURE 8 of this manual.

Part No. 1106628

41

Solara jr.™

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Solara jr Solara jr Table of Contents Procedure 8 Wheel LOCKS/ANTI-TIPPERS Special Notes Special NotesLabel Locations Label LocationsInvacare Solara JR SpecificationsSpecifications Information for Healthcare PROFESSIONALS/ Assistants Procedure General GuidelinesGeneral Guidelines Anterior Forward TiltStability Warning Stability ALL ModelsStability ALL Models Except Recliners General Warnings Stability Recliner Models onlyOperating Information Weight Limitation Weight TrainingCoping with Everyday Obstacles SAFETY/HANDLING of WheelchairsStability and Balance Unoccupied Occupied Percentage of Weight DistributionStep Tube TippingMethod 1 Wheelchair with Step Tubes Tipping Curbs Method 2 Wheelchair Without Step Tube StairwaysTransferring to and from Other Seats ESCALATORS? SorrySafety Inspection Safety Inspection ChecklistMaintenance TroubleshootingProcedure 2SAFETY Inspection Maintenance Safety PrecautionsTransporting Transporting ProcedureTransporting the Invacare Solara JR Procedure Front Riggings INSTALLING/REMOVING Swingaway Footrest FigureFront Friggings RemovingFront Riggings Procedure Adjusting Swingaway Footrest HeightHeight Adjustment Ranges Front RiggingsAdjusting Adjustable Angle FLIP-UP Footplates Figure Composite Footplate Disassembly Front RiggingsprocedureReassembly Articulating Footplate Heel Loop ReplacementAdjusting the Legrest Adjusting the Elevating LEGREST/CALFPAD Assembly FigureAdjusting the Calfpad CalfpadARMS/POSITIONING Straps USING/ADJUSTING Dual Point Arms FigureReplacing Dual Point ARM Clothing Guards Figure Procedure ARMS/POSITIONING StrapsReplacing Dual Point ARM PAD Figure INSTALLING/ADJUSTING USING/INSTALLING/ADJUSTING Cantilever ArmsUsing Figure ARM PAD Replacement for Cantilever Arms Figure Adjusting the T-ARMS INSTALLING/REMOVING T-ARMS FigureInstalling T-ARMS Adjusting T-ARM Height FigureInside T-Arm Post Arm Release Lever Locked Position DepthOutside T- Arm Post SocketAdjusting T-ARM Sockets Figure Adjusting T-ARM Transfer Assists AND/OR Side Guards FigureHex screws and washers are removed Arm Arm Clamp Slot Arm SocketReplacing INSTALLING/REPLACING Seat Positioning Straps FigureSide Guard Transfer Assist Socket ScrewsBack Cane Locknut Hex Screw Chest Positioning Strap INSTALLING/REPLACING Chest Positioning Straps FigureBACK/SEAT FOLDING/UNFOLDING Back Assembly FigureINSTALLING/REMOVING Stroller Handles Figure Detail a QUICK-RELEASE PIN Installed Installing FigureRemoving Figure Quick-Release Pin Or bolt and locknut Recliners onlyStroller Handle Thumbscrew Release Lever Procedure BACK/SEAT Adjusting FigureLocked Position RAISING/LOWERING Using the Telescoping Back Canes FigureStoring OpenFixed Back Canes Figure INSTALLING/REPLACING the Back UpholsteryClamp Spreader Bar Set Screw Back Canes Installing and Removing a Seating SystemREMOVING/INSTALLING the Spreader BAR Figure Wheelchair Front Installing the Seat Cushion FigureRear WHEELS/FORKS Procedure REMOVING/INSTALLING Rear Wheels FigureWHEELS/FORKS Quick Release AxleSEAT-TO-FLOOR Height Adjustment Adjusting the Quick Release Axle FigureProcedure WHEELS/FORKS Axle Mounting Plate Locking PinsFork Dust Cover Caster Headtube Adjusting Forks FigureProcedure Wheel LOCKS/ANTI-TIPPERS Adjusting Wheel Locks Figures 1Wheel TIPPERS-LOCKS/ANTI 16-INCH Rear Wheels 18 24-INCH Rear WheelsWheel LOCKS/ANTI-TIPPERS Using the Wheel LocksFoot Activated Wheel Locks 12-INCH Wheels only Figure Adjusting INSTALLING/ADJUSTING ANTI-TIPPERS Figure2 to 2-inch ClearanceAnti-tipper Ground/FloorTILT/RECLINE TILT/RECLINE ProcedureEngaging Tilt in SPACE/RECLINER Operation Engaging TILT-IN-SPACE Figure Procedure TILT/RECLINETILT-IN-SPACE Tilt SlideGas Cylinder TILT/RECLINE Procedure Recliner Operation FigureCable Locking Nut Trigger Release Lever Cable Adjusting Nut Adjusting Tilt Trigger Release Cables FigureBearing Housing Adjusting Upper Tilt Locking Collar FigurePositioning Tilt Locking Collars Magnetic protractor reads desired angle of tiltReplacing the Headrest Upholstery Replacing the Back UpholsteryHeadrest Upholstery Extension Back Cane Back UpholsteryInch Seat Cushion Position Adjusting the Back Height Recliner Models only FigureProcedure Contracture Footplate Contracture Assembly Angle Adjustment FigureFootplatecontracture Mounting ScrewAngle Adjustment of the Contracture Footplate Figure Using the Optional Quick Release PIN FigureContracture Footplate Depth Adjustment Figure ContractureReplacing the Contracture Footplate Heel Loop Figure Contracture Footplate Height Adjustment FigureMounting Hole ContractureSolara jr Solara jr Warranty Limited WarrantyWarranty One Invacare Way

1106628 specifications

The Invacare 1106628 is a robust and innovative mobility solution designed to enhance the quality of life for individuals with limited mobility. This power wheelchair combines advanced technology and user-friendly features, making it an excellent choice for both indoor and outdoor use.

One of the standout characteristics of the Invacare 1106628 is its versatile seating system, which provides optimal comfort and support. The seat is designed to accommodate various body types and can be adjusted to ensure perfect alignment and positioning. Additionally, the chair includes a contoured backrest that offers lumbar support, promoting good posture during extended use.

Technology plays a significant role in the design of the Invacare 1106628. The wheelchair is equipped with a powerful motor and a durable battery system, allowing for a long driving range and reliable performance. With a top speed that makes navigating urban settings easy, users can enjoy both independence and accessibility. The advanced joystick control allows for smooth and precise maneuvering, enabling efficient navigation through tight spaces.

The wheelchair also boasts a sturdy construction, ensuring it can withstand the rigors of daily use. The frame is made from high-quality materials, providing durability while remaining lightweight enough for easy transport. Its compact design enhances maneuverability, making it suitable for use in various environments, from bustling shopping malls to narrow hallways in homes.

Safety features are paramount in the design of the Invacare 1106628. The wheelchair comes with anti-tip wheels, ensuring stability during movement, particularly when climbing slopes or navigating uneven terrain. The durable tires are designed for excellent traction, further enhancing safety and control in various outdoor settings.

In terms of additional features, the Invacare 1106628 includes customizable options such as adjustable armrests, footrests, and various accessory attachments. This flexibility allows users to tailor the wheelchair to their specific needs, enhancing overall comfort and usability.

In conclusion, the Invacare 1106628 is a well-engineered power wheelchair that incorporates advanced technology, safety features, and customizable options. It is designed to provide individuals with mobility challenges the independence and support they need, making it a valuable asset for users seeking to improve their quality of life. Whether navigating through their home or enjoying the great outdoors, the Invacare 1106628 delivers on performance, comfort, and durability.
Top Page Image Contents