Invacare 1106628 Adjusting T-ARM Transfer Assists AND/OR Side Guards Figure, Slot Arm Socket

Page 31
FIGURE 9 - ADJUSTING T-ARM
SOCKETS

ARMS/POSITIONING STRAPS

PROCEDURE 5

 

 

4.Re-secure the arm tube to the T-arm post with the two (2) socket screws. Torque to 60- 70 in./lbs.

5.Reattach the arm pad to the arm tube with the two (2) phillips screws. Tighten securely.

6.Repeat for the opposite side, if necessary.

ADJUSTING T-ARM SOCKETS (FIGURE 9)

NOTE: Perform this procedure if the T-arm is too loose in the socket or does not easily slide up and down in the socket.

1.Remove the rear wheels from the wheel- chair, if necessary. Refer to REMOVING/ INSTALLING REAR WHEELS in PROCE- DURE 7 of this manual.

2.Loosen, but do not remove the four (4) hex screws and washers that secure T- arm socket to T- arm clamp.

NOTE: The T-arm socket will disassemble if the four

(4) hex screws and washers are removed.

T-Arm

 

 

T-Arm Clamp

Hex Screws and

 

Washers

Hex Screws and

 

 

Washers

Slot

T-Arm Socket

Locking Lever

 

ARMS/POSITIONING STRAPS

3.Slide the T-arm into the T-arm socket

until the locking lever is in the slot in the T-arm socket and an audible "click" is heard.

4.Squeeze the T-arm socket the T-arm clamp together until the socket is flush with the T- arm.

5.While holding the T-arm socket and the T-arm clamp together, tighten the four (4) hex screws and washers. Tighten securely.

6.Press in on the locking lever and lift the T-arm straight up and out of the T-arm socket.

7.Repeat STEPS 3-6, if necessary until the T-arm slides in the T-arm socket as desired.

8.If necessary, install rear wheels. Refer to REMOVING/INSTALLING REAR WHEELS in PROCEDURE 7 of this manual.

ADJUSTING T-ARM TRANSFER ASSISTS AND/OR SIDE GUARDS (FIGURE 10)

1.Remove the T-arm from the wheelchair. Refer to INSTALLING/REMOVING T-ARMS in this procedure of the manual.

2.Remove the two (2) socket screws that secure the side guard to the bottom clamp.

NOTE: Adjusting the side guards will directly affect the position of the transfer assist.

3.Perform one (1) of the following:

Small Side Guards - Move the bottom clamp up one (1) of two (2) mounting positions in the side guard.

Large Side Guards - Move the bottom clamp up one (1) of three (3) mounting positions in the side guard.

Part No. 1106628

31

Solara jr.™

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Solara jr Solara jr Table of Contents Procedure 8 Wheel LOCKS/ANTI-TIPPERS Special Notes Special NotesLabel Locations Label LocationsSpecifications SpecificationsInvacare Solara JR Anterior Forward Tilt Procedure General GuidelinesInformation for Healthcare PROFESSIONALS/ Assistants General GuidelinesStability ALL Models Except Recliners Stability ALL ModelsStability Warning Operating Information Stability Recliner Models onlyGeneral Warnings Weight Limitation Weight TrainingStability and Balance SAFETY/HANDLING of WheelchairsCoping with Everyday Obstacles Unoccupied Occupied Percentage of Weight DistributionMethod 1 Wheelchair with Step Tubes TippingStep Tube Tipping Curbs Method 2 Wheelchair Without Step Tube StairwaysTransferring to and from Other Seats ESCALATORS? SorrySafety Inspection Safety Inspection ChecklistMaintenance Safety Precautions TroubleshootingMaintenance Procedure 2SAFETY InspectionTransporting the Invacare Solara JR Transporting ProcedureTransporting Removing INSTALLING/REMOVING Swingaway Footrest FigureProcedure Front Riggings Front FriggingsFront Riggings Adjusting Swingaway Footrest HeightFront Riggings Procedure Height Adjustment RangesAdjusting Adjustable Angle FLIP-UP Footplates Figure Heel Loop Replacement Front RiggingsprocedureComposite Footplate Disassembly Reassembly Articulating FootplateCalfpad Adjusting the Elevating LEGREST/CALFPAD Assembly FigureAdjusting the Legrest Adjusting the CalfpadARMS/POSITIONING Straps USING/ADJUSTING Dual Point Arms FigureReplacing Dual Point ARM PAD Figure Procedure ARMS/POSITIONING StrapsReplacing Dual Point ARM Clothing Guards Figure Using Figure USING/INSTALLING/ADJUSTING Cantilever ArmsINSTALLING/ADJUSTING ARM PAD Replacement for Cantilever Arms Figure Adjusting T-ARM Height Figure INSTALLING/REMOVING T-ARMS FigureAdjusting the T-ARMS Installing T-ARMSSocket DepthInside T-Arm Post Arm Release Lever Locked Position Outside T- Arm PostSlot Arm Socket Adjusting T-ARM Transfer Assists AND/OR Side Guards FigureAdjusting T-ARM Sockets Figure Hex screws and washers are removed Arm Arm ClampTransfer Assist Socket Screws INSTALLING/REPLACING Seat Positioning Straps FigureReplacing Side GuardBack Cane Locknut Hex Screw Chest Positioning Strap INSTALLING/REPLACING Chest Positioning Straps FigureINSTALLING/REMOVING Stroller Handles Figure FOLDING/UNFOLDING Back Assembly FigureBACK/SEAT Quick-Release Pin Or bolt and locknut Recliners only Installing FigureDetail a QUICK-RELEASE PIN Installed Removing FigureLocked Position Procedure BACK/SEAT Adjusting FigureStroller Handle Thumbscrew Release Lever Open Using the Telescoping Back Canes FigureRAISING/LOWERING StoringFixed Back Canes Figure INSTALLING/REPLACING the Back UpholsteryREMOVING/INSTALLING the Spreader BAR Figure Installing and Removing a Seating SystemClamp Spreader Bar Set Screw Back Canes Rear Installing the Seat Cushion FigureWheelchair Front Quick Release Axle REMOVING/INSTALLING Rear Wheels FigureWHEELS/FORKS Procedure WHEELS/FORKSAxle Mounting Plate Locking Pins Adjusting the Quick Release Axle FigureSEAT-TO-FLOOR Height Adjustment Procedure WHEELS/FORKSFork Dust Cover Caster Headtube Adjusting Forks Figure16-INCH Rear Wheels 18 24-INCH Rear Wheels Adjusting Wheel Locks Figures 1Procedure Wheel LOCKS/ANTI-TIPPERS Wheel TIPPERS-LOCKS/ANTIFoot Activated Wheel Locks 12-INCH Wheels only Figure Using the Wheel LocksWheel LOCKS/ANTI-TIPPERS Ground/Floor INSTALLING/ADJUSTING ANTI-TIPPERS FigureAdjusting 2 to 2-inch ClearanceAnti-tipperEngaging Tilt in SPACE/RECLINER Operation TILT/RECLINE ProcedureTILT/RECLINE Tilt Slide Procedure TILT/RECLINEEngaging TILT-IN-SPACE Figure TILT-IN-SPACEGas Cylinder TILT/RECLINE Procedure Recliner Operation FigureCable Locking Nut Trigger Release Lever Cable Adjusting Nut Adjusting Tilt Trigger Release Cables FigureMagnetic protractor reads desired angle of tilt Adjusting Upper Tilt Locking Collar FigureBearing Housing Positioning Tilt Locking CollarsBack Upholstery Replacing the Back UpholsteryReplacing the Headrest Upholstery Headrest Upholstery Extension Back CaneInch Seat Cushion Position Adjusting the Back Height Recliner Models only FigureMounting Screw Contracture Assembly Angle Adjustment FigureProcedure Contracture Footplate FootplatecontractureContracture Using the Optional Quick Release PIN FigureAngle Adjustment of the Contracture Footplate Figure Contracture Footplate Depth Adjustment FigureContracture Contracture Footplate Height Adjustment FigureReplacing the Contracture Footplate Heel Loop Figure Mounting HoleSolara jr Solara jr Warranty Limited WarrantyWarranty One Invacare Way

1106628 specifications

The Invacare 1106628 is a robust and innovative mobility solution designed to enhance the quality of life for individuals with limited mobility. This power wheelchair combines advanced technology and user-friendly features, making it an excellent choice for both indoor and outdoor use.

One of the standout characteristics of the Invacare 1106628 is its versatile seating system, which provides optimal comfort and support. The seat is designed to accommodate various body types and can be adjusted to ensure perfect alignment and positioning. Additionally, the chair includes a contoured backrest that offers lumbar support, promoting good posture during extended use.

Technology plays a significant role in the design of the Invacare 1106628. The wheelchair is equipped with a powerful motor and a durable battery system, allowing for a long driving range and reliable performance. With a top speed that makes navigating urban settings easy, users can enjoy both independence and accessibility. The advanced joystick control allows for smooth and precise maneuvering, enabling efficient navigation through tight spaces.

The wheelchair also boasts a sturdy construction, ensuring it can withstand the rigors of daily use. The frame is made from high-quality materials, providing durability while remaining lightweight enough for easy transport. Its compact design enhances maneuverability, making it suitable for use in various environments, from bustling shopping malls to narrow hallways in homes.

Safety features are paramount in the design of the Invacare 1106628. The wheelchair comes with anti-tip wheels, ensuring stability during movement, particularly when climbing slopes or navigating uneven terrain. The durable tires are designed for excellent traction, further enhancing safety and control in various outdoor settings.

In terms of additional features, the Invacare 1106628 includes customizable options such as adjustable armrests, footrests, and various accessory attachments. This flexibility allows users to tailor the wheelchair to their specific needs, enhancing overall comfort and usability.

In conclusion, the Invacare 1106628 is a well-engineered power wheelchair that incorporates advanced technology, safety features, and customizable options. It is designed to provide individuals with mobility challenges the independence and support they need, making it a valuable asset for users seeking to improve their quality of life. Whether navigating through their home or enjoying the great outdoors, the Invacare 1106628 delivers on performance, comfort, and durability.
Top Page Image Contents